How to properly wind the line on the grass trimmer video • CIMFLOK.COM

Stihl Trimmer Head-How To Rewind A 2 String Head. 25-2

How does the head with a fishing line work on a brushcutter why you need to know the principle of operation

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the grass trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above.

The principle of operation of the semi-automatic grass trimmer coil is as follows:

Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
A spring acts on the coil, which presses it against the splines in the cover structure
A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the fishing line is unwound from the drum, increasing in length
After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without adversely affecting the gearbox and engine of the tool, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the grass trimmer reel. After all, it is this very moment that causes difficulties for most owners of special tools.

The video shows in detail how to wind the line onto the spool of a grass trimmer or brushcutter. Refueling with mowing line.

String Trimmer Head | How to install new trimmer line on a traditional bump head

Changing the line on the trimmer

This article will tell you how to change the line on the trimmer. For some people, this job may not be easy. But the step-by-step instructions that are available here will help you in this matter.

So the first thing to do is remove the gear cover. We combine the hole on the side of the curly lower washer and the axial recess, insert a screwdriver to fix the shaft from scrolling. Now unscrew the nozzle. The thread on the shaft, as a rule, has a reverse thread, take this into account when unscrewing.

Next, the disassembly of the nozzle follows. There, the lid is secured with latches through the holes. So you just have to push these clips into the holes and the cover will come off. If the attachment has an automatic semi-automatic line feeding mode, it means that there is a spring inside that can simply fly out when the lid is opened, be prepared for this. We lay out all the removed parts neatly in order.

Now it’s time to take the line and rewind 5 meters from it, cut off this piece. Pay attention to its thickness, do not wind a line of greater thickness on the unit than specified in the manual for the tool. Otherwise, there will be an increased load on the engine and higher fuel consumption during operation. We bend the measured line in half to find the middle and get a loop.

There are a couple of notches in the middle of the coil, sometimes these are not notches, but holes located opposite each other. With a loop we cling to one of the grooves and wind the fishing line counterclockwise. If the reel has 2 compartments, then we wind each end of the fishing line on them separately. Leave the last 15-20 cm free and clamp them while in the recesses of the coil.

We assemble the device again, pull the free ends of the fishing line into the holes on the body. We put on the cover, snapping the latches into their grooves. Now you can pull out these loose ends of the line.

It remains only to attach the working node in place, as in the first paragraph. Do not forget about reverse rotation on screwing.

Now you can learn how to wind the line around the grass trimmer. Actually, the whole process was detailed above. No time-consuming operations requiring the presence of specialists. Your lawnmower is ready for use again.

Winding the Line Correctly to the Spool of the Grass Trimmer

What you need to know about grass trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its application on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline grass trimmers with brushcutters (from 2.4 up to 3.2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the coil of your grass trimmer, then it is time to change and reload the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the fishing line in the grass trimmer reel.

Method 2. how to properly put the line on the reel of the brushcutter with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into the brushcutter is the same as with the first method, and to make sure of this, below are detailed instructions:

There are two equal length pieces of material that you can use.
One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
The fishing line should be hooked onto the bracket, and wind it in observing the direction of the arrow
The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
Manipulations with the second end of the fishing line are carried out in the same way.
The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in a brushcutter will help not only correctly, but also quickly perform the replacement procedure. Assembling the grass trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to comfortably fix the tool. Video instruction is presented below.

How to wind line in a grass trimmer?

When refueling the line for the first time, this process may seem quite laborious, but with time and dexterity, the task is solved much faster.

In order to fill the line, you must:

Take the coil, unscrew its cap. Some coils are threaded to the left, so the lid must be unscrewed in the required direction.
Measure five meters of line;
Fold this segment in half, that is, determine where the middle is;
Next, place this middle of the line in a special hole on the reel;
Wind the line in the direction of the arrow;
If there are two places for winding, then the first part of the line should be wound on one half of the reel, and the second part on the other half;
Push both ends of the fishing line into the holes of the reel;
Screw on the lid.

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only turn in one direction.

Private home owners know how essential a tool such as a grass trimmer is. It can be gasoline and electric, but they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out in the process of use, so how to wind the coil of the grass trimmer, we will consider in detail in the material.

How to wind the line onto the reel of the grass trimmer video

Warranty production of the factory fill of the grass trimmer will inevitably require a line change. Having a very rough idea of how to thread the line into the reel of a grass trimmer on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2 5 m.
One end of the line is inserted into the fixing technological hole located inside the spool.
The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
The left end of the line is passed through the hole in the outer part of the reel.
The bobbin halves are assembled and put on the trimmer bar.

Step-by-step instructions on how to wind the reel of the grass trimmer and lawn mower

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the spool about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of brushcutters and trimmers you use, you decide on your own which option is suitable.

What you need to know about grass trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its application on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline grass trimmers with brushcutters (from 2.4 up to 3.2 mm).

Method 1. how to properly wind the line or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out the amount of line you need to refuel to charge the reel. To do this, wind the rig inside the coil until it is aligned with the side protrusions. In this case, the rigging should not go beyond these extreme protrusions.

The thicker the equipment used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly tuck the harness into the aiming of the grass trimmer or brushcutter is as follows:

To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
After that, take the second end from the other side, and bend it in half. Move to it so that the measured protrusion of 15 cm is preserved
There is a slot in the inner baffle of the coil, into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
Next, we figure out the direction of winding the line. If you wind the rig in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the line and wind it in the correct direction, inspect the surface of the spool. It should indicate the direction of winding (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
This arrow-shaped pointer can also have the designation, as in the example above “WIND LINE”, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the line, wind it on the drum in the opposite direction to the indication of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is no separator, then the equipment must be laid in the appropriate distribution order.
When almost all the fishing line is wound on a reel, you will need to do the following. place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then do the same procedure with the other end, placing it in the hole on the parallel side
We insert the coil into the head, first passing the ends of the fishing line into the holes of the drum
We put the drum in place and, by pulling the ends of the line, we disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover until the latch engages.
At this point, the process of how to replace the fishing line on the trimmer is completed, and if necessary, you can cut only the ends (if their length does not suit), and install the assembled drum on the tool

With how to put the drum in place, no difficulties arise. There is a second way, how to charge the mowing equipment in the brushcutter. What is the difference and how the second method of threading the line onto the reel of the brushcutter is carried out, we will find out in detail.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

one groove. both antennae are wound together in one groove;
two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference in line winding in double-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to thread the line into the spool of the grass trimmer and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:

Line selection

For the threading of the line into the trimmer head to be successful, it is important not to miscalculate with the choice of consumables. The thicker the cord you tuck in, the thicker and tougher the grass it will be able to cut. Often a universal line is used, the diameter of which is 2 mm. You can choose a diameter suitable for the mower in the following ways:

Refer to the instructions that came with the trimmer for line thickness information.
Pay attention to the bobbin itself. Sometimes information about the possible diameters of the fishing line is applied on it.
Another option is to try inserting the cord into the exit hole. If it easily goes into it, then the selected line diameter is suitable for use.

Grass trimmer reel

You can choose a cord thread according to the type of engine. If the line is too thick, then the resistance to rotation will increase. in this case, the engine will overheat and will soon fail. Helpful hints:

For an electrical device with a motor less than 500 V, a 1.3 mm thread is suitable. If you can’t find one, then you can use a 1.6 mm line. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
With a petrol grass trimmer, the shaft mower counts. For the folded version, a 2 mm cord is often used. If the shaft is straight, use a 2.4-2.5 or 3mm thread. The thickest line is installed on powerful devices. from 1.3 kW.

Pay attention to the type of section of the cord thread. Some popular options:

The most common round lines. They mow fresh grasses well, but they cope worse with shrubs, dead wood.
Twisted (spiral) cord is not very strong, but is good for thin young grass.
Serrated thread with sharp edges is ideal for large weeds in a neglected area.
You can mow your lawn more evenly with rectangular, star or square grass trimmer lines, but they are not very strong.
Strongest. two-piece inner-core round cord.

Types of grass trimmer line

Please note that you cannot use wire, metal strings and cables, as well as ordinary fishing thread instead of fishing line. The device will be dangerous to both the user and others. So the cable or similar products will gradually begin to work, as a result, their ends will unravel, and small pieces will scatter at high speed.

Single-barb grass trimmer reel

Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the grass trimmer reel.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

How to remove the spool from the grass trimmer and remove the line

Initially, remove the line from the spool of the grass trimmer before threading it into the spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

It is interesting! The tooling can be changed directly on the tool, but if you are doing this for the first time, it is still recommended to remove the head and study the detailed winding process. After the technology has been mastered, you can perform replacement work on a trimmer, a brushcutter or a petrol cutter.

The instruction on how to unscrew the manual head on the trimmer is as follows:

Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand.
The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
To unscrew, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
After that, you can proceed to dismantling. To do this, you do not need to pull it with all your strength, but slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
When reinstalling, fit the head into the square slots

This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

Periodic removal of the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction to the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to change the grass trimmer line. The video below shows the detailed process of how to open the grass trimmer coil and disassemble it.

Spool Trimmer Heads

The main elements of the trigger is the mowing head, which is a cylindrical body with a bobbin inserted inside. The fishing line (cord) is tucked into it. The heads differ from each other in the way of feeding and threading the cord. There are three types of heads in total:

Automatic. The line is then fed as the user decreases the engine speed. Automatic cord feeding is very convenient when there is a lot of work to be done. The disadvantage of such a head is the high thread consumption.
Semi-automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is designed in such a way that the line begins to automatically lengthen while the grass trimmer is operating at full speed. You just need to lightly bang the head of the machine on the ground (this will remove the blocking of the line), and the cord will be pulled out of the bobbin due to centrifugal force. Then the line is cut to the required length with a knife, which is located on the protective cover.
Manual. To lengthen the cord, it is necessary to stop the apparatus. After that, the line will need to be pulled out manually.

Types of trimmer spools

Method 2. how to properly put the line on the reel of the brushcutter with photo description and video

There are two equal length pieces of material that you can use.
One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
The fishing line should be hooked onto the bracket, and wind it in observing the direction of the arrow
The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
Manipulations with the second end of the fishing line are carried out in the same way.
The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in a brushcutter will help not only correctly, but also quickly perform the replacement procedure. Assembling the grass trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to comfortably fix the tool. Video instruction is presented below.

Trimmer head with two antennae

After removing the spool from the spool body, we determine the number of strands for winding the line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the grass trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the grass trimmer, the knife installed on the protection will cut off the excess.

How to Wind a Trimmer Head

Sources:

http://schemy.ru/info/kak-namatyvat-lesku-na-katushku-trimmera-video/
http://kalibrtractor.ru/instrumenty/kak-namotat-lesku-na-katushku-trimmera-sposoby-namatyvaniya-i-video.html