How to saw an electric saw chain tree. Features of the location of the engine

Dawed Electric Chain Instruction Instructions

Electric chain saw. an indispensable assistant with a variety of household and professional tasks. There is no special difference between the functioning of the power plant and the chainsaw. The difference is only in the type of engine. Many users positively speak about the operation of an electric drive, noting the ease of use and maintenance, the lack of need to refuel saw equipment with fuel and a long service life with proper use with proper use. Since it is correct to saw with an electric saw?

Before sawing, the equipment must be assembled. As a rule, the power unit itself is delivered in the collected form. Separately in the box there is a guide tire, a chain and a set of necessary keys for assembling and servicing a saw. When installing the chain on the tire, you need to be careful, since it is sharply sharpened.

It is important to observe safety measures and work in special gloves.

The setting of the chain itself is correct from the tire tip. Mount the tire with a chain on the bolts, start the chain on the asterisk and check the correct direction of the cloves of the chain. If the direction coincides with what is indicated on the lid, put it on and twist the fastener nut with the key that comes in the kit.

Checking serviceability and starting

Read how to cut the LED tape correctly

Assembly, driving saw, starting work

Consumer power pipes come to consumers in the collected state, it is required to install a saw headset, and the chain tension. With proper tension, the gap between the guides and the chain is 3-4 mm. Over time, the chain can stretch, the tension weakens, so the correct tension is installed by the adjusting screw.

It should be borne in mind that the tension of the cold and hot circuit is different, and a poorly stretched chain is a serious source of danger. After running in the saw, it is allowed to begin the full operation of the electric saw.

Before the start of sawing, the level of oil is checked, if necessary, add to the specified mark. The serviceability of the lubricant system is tested in a simple way: after refueling, turn on the saw, let it work for some time in raised hands above the paper spread out from the bottom. If oil spots appear on it, then the lubrication system is good. In the course of work, the oil level is controlled constantly and add.

Be sure to test the state of locking saw saw.

The reasons that the electric saw does not drink poorly or does not saw under the load, it saws unevenly to the side or crookedly to the side, there may be: a blurry chain, sagging of the chain, lack of oil in the lubrication system, incorrect working techniques.

How to use electric saw chain: tips and recommendations

• Constantly test the voltage in the network and do not work at low voltage, this is fraught with an overheating of the engine and breakdowns.
• Do not use a chain saw in too intense mode. If you need to perform a large amount of work, it is more advisable to choose a sparing pace of operation with interruptions.
• When sawing large logs or trees, you should be especially careful: the electric saw must be installed at the lowest angle to the workpiece in order to avoid jerks.
• Particular attentiveness must be observed with a forest roll, it is necessary to master the correct techniques and technique of work, take into account the direction of the fall of the tree, the speed of the wind, the presence of surrounding objects (power lines, poles, structures).
• Before the onset of the season of spring work, if the saw was in a cold room, the tool should be kept in a heated room for at least a day. This will allow the condensate in the winding of the electric engine and avoid short circuit when turned on.
• Before using a chain saw, you should undermine the chain, this will significantly extend its service life. Periodically, you should contact a professional service for sharpening a circuit.
• When working with a saw with an extension cord, it is necessary to correctly choose a network cable along the cross.section and protective shell, install a lock from random loss from a socket.
• If it is assumed not to use electric saw for a long time, it is necessary to remove the saw headset. the guide and the chain, save them in a container with butter.

How to cut an electric saw correctly, what safety requirements can be fulfilled in video reviews. Experienced owners are divided by rational techniques and skills that ensure the durable operation of the tool.

How to cut a chain electric saw correctly

Many after acquiring an electric saw and some time of operation are faced with difficulties when cutting wood on firewood. These difficulties arise due to the fact that the owner simply does not know how to use the saw correctly. And the secret is quite simple. you need to have good emphasis, monitor the sharpening and proper tension of the chain. Regularly change from one side to the other side the position of the working area, so that gritting occurs evenly. Be sure to see that the lubrication tank is filled.

The sequence of actions during work is as follows:

• Attach a chain saw to the tree;
• Run the saw;
• Saw in even movements, then raising the handle up, then lowering down;
• If it became inconvenient to saw, then the saw must be lowered below and continue the cut.

In order to facilitate the process of sawing itself, it is necessary to constantly monitor the tension of the chain. If it is poorly stretched, then it can fly off the tire, if pulled, then the saw will overheat and break.

What problems can arise?

With proper operation of problems with a saw, does not occur. But if you ignore the basic rules, then the saw can quickly fail, and the owner will assume that he got a poor.quality tool.

The main malfunctions arise for the following reasons:

• Stress jumps. The most common problem due to which breakdowns arise is poor wiring and unstable voltage in the network.
• You can’t work with electric saw for a long time without a break. The main problem of the owners is the desire to “finish a little more”, which affects the overheating of the engine and, as a result, the failure of the tool. Adhere to the Rules of 30 minutes of work, 15 minutes break.
• Lack of lubrication in the tank entails the failure of the motor. For a frequent, in modern saws an automatic supply of lubrication, but if it is not, then you need to lubricate it yourself after about 4 hours.
• Do not carry out overload. This applies to sawing logs of the thickness for which a certain model is designed. And the desire to cut a tree of greater thickness than recommended in the instructions, leads to a breakdown of the saw.
• A common manufacturer’s mistake is a rigid adhesion of the gearbox with an anchor. Because of this, the gearbox can jam. If a strong tree, then gears begin to wear out faster/, so avoid load.

What problems can arise?

With proper operation of problems with a saw, does not occur. But if you ignore the basic rules, then the saw can quickly fail, and the owner will assume that he got a poor.quality tool.

The main malfunctions arise for the following reasons:

• Stress jumps. The most common problem due to which breakdowns arise is poor wiring and unstable voltage in the network.
• You can’t work with electric saw for a long time without a break. The main problem of the owners is the desire to “finish a little more”, which affects the overheating of the engine and, as a result, the failure of the tool. Adhere to the Rules of 30 minutes of work, 15 minutes break.
• Lack of lubrication in the tank entails the failure of the motor. For a frequent, in modern saws an automatic supply of lubrication, but if it is not, then you need to lubricate it yourself after about 4 hours.
• Do not carry out overload. This applies to sawing logs of the thickness for which a certain model is designed. And the desire to cut a tree of greater thickness than recommended in the instructions, leads to a breakdown of the saw.
• A common manufacturer’s mistake is a rigid adhesion of the gearbox with an anchor. Because of this, the gearbox can jam. If a strong tree, then gears begin to wear out faster/, so avoid load.

Tips and recommendations

If the saw saws a crookedly, then the problem can be in a hidden chain, and one row is stronger than the other. Sharpen or replace the chain with a new. To avoid uneven wear, turn the tire during operation.

If it does not gain momentum, then it is necessary to replace the coal brushes that wear out over time.

In order not to be afraid of voltage drops, set a stabilizer.

Tips and recommendations

If the saw saws a crookedly, then the problem can be in a hidden chain, and one row is stronger than the other. Sharpen or replace the chain with a new. To avoid uneven wear, turn the tire during operation.

If it does not gain momentum, then it is necessary to replace the coal brushes that wear out over time.

In order not to be afraid of voltage drops, set a stabilizer.

Alexander:

I used to saw it with a hand saw and lit up, and then I decided to buy a power plant. I was surprised for a long time why I hadn’t bought it before. It is light, powerful and perfectly copes with cutting the crown. The only thing that I don’t like is regular trips to the service center for sharpening the circuit.

Ivan Ivanovich:

My son.in.law gave an electrical saw, so I’m not getting enough. Work in the garden went faster. I even began to cook firewood for barbecue. You just need to follow the grease regularly. I once missed that it was over, so the sound went another right away and it became harder to work.

What problems can arise?

With proper operation of problems with a saw, does not occur. But if you ignore the basic rules, then the saw can quickly fail, and the owner will assume that he got a poor.quality tool.

The main malfunctions arise for the following reasons:

• Stress jumps. The most common problem due to which breakdowns arise is poor wiring and unstable voltage in the network.
• You can’t work with electric saw for a long time without a break. The main problem of the owners is the desire to “finish a little more”, which affects the overheating of the engine and, as a result, the failure of the tool. Adhere to the Rules of 30 minutes of work, 15 minutes break.
• Lack of lubrication in the tank entails the failure of the motor. For a frequent, in modern saws an automatic supply of lubrication, but if it is not, then you need to lubricate it yourself after about 4 hours.
• Do not carry out overload. This applies to sawing logs of the thickness for which a certain model is designed. And the desire to cut a tree of greater thickness than recommended in the instructions, leads to a breakdown of the saw.
• A common manufacturer’s mistake is a rigid adhesion of the gearbox with an anchor. Because of this, the gearbox can jam. If a strong tree, then gears begin to wear out faster/, so avoid load.

Rules for the safe use of chain electric saws

I used to saw it with a hand saw and lit up, and then I decided to buy a power plant. I was surprised for a long time why I hadn’t bought it before. It is light, powerful and perfectly copes with cutting the crown. The only thing that I don’t like is regular trips to the service center for sharpening the circuit.

My son.in.law gave an electrical saw, so I’m not getting enough. Work in the garden went faster. I even began to cook firewood for barbecue. You just need to follow the grease regularly. I once missed that it was over, so the sound went another right away and it became harder to work.

How to work with a saber’s saw?

Sable saw did not find widespread among domestic consumers. By structure and principle of operation, it is most similar to a hacksaw. Only instead of human strength, the electric motor works. It is easy to use such a tool, because the ergonomic handle lies well in the hand.

Ideal for working in a garden, where you need to cut down a few branches. Thanks to the thin working surface, the saw will not cut off the excess. The advantage of the saber saw is that it can be sawed not only by wood, but also with a stone, ceramic materials, a gas block, glass, plastic, etc.D.

What problems can arise?

Can stop while working. The main reason for this is the operation of the security system from overload. Perhaps the canvas of the saw turned off, or the owner made too much effort when cutting, a bad canvas or complete wear of coal brushes is also possible.

If the saw does not turn on, then check the power cord. Perhaps somewhere the wire was damaged or not electricity.

If the saw canvas is incorrectly fixed, then the hexagonal key will wear out.

Proper operation of the electric saw

Many amateur gardeners, as well as professionals who are engaged in work with wood and harvesting of wood, use saws, and a chain saw of electric. As the name understands the working part of it has a chain, which during operation moves along the bus.

Electric saw Karcher CS-330BP

In terms of functionality of saw, the electrical is no different from the chainsaw. The only difference is in the type of engine and attachment to the place where there are rosettes with alternating current. Electric saws are also different and the consumer can choose, based on the tasks that he plans to solve with this tool.

How the electric saw is arranged

The speed of rotation is often not indicated. It is clear that there is a collector engine inside, but how fast it is. Pay attention to the parameter of the speed of the circuit. It is expressed by meters in sec (13.5) and shows how quickly the links move. It is known that the length of the tire is 14 inches (35.5 centimeters). For reference: the electric engine tire is called the metal frame, the chain runs along it.

The total length of the links is about 85 centimeters. We take a reserve for the tension mechanism and the transverse size. This means that in a second the full number of revolutions is n = 13.5 / 0.85 = 16. About 950 it turns out per minute. This is not the engine frequency, but the number of revolutions. But there is information on the drive asterisk, it is written: 6t x 9.53. This means that the teeth are 6, and the distance between the teeth is 3/8 inches (9.53 millimeters). It remains to change these two digits to obtain the length of the circle: 6 x 9.53 = 60 millimeters (rounded).

It turns out that the drive star makes a circle 85/6 = 15 revolutions, which gives the speed of rotation of the shaft about 14000 rpm. Provided that there is no gearbox inside. Inside there is a high.cost collector engine (you can’t bring asynchronous to such a speed), which means that there is no choice. Sometimes a gearbox is used, in other cases the drive of a direct. In the second case, the electric saw weighs less and there are fewer details that can break.

The motor lies in the transverse relative to the movement of the plane circuit for obvious reasons. The shaft star extends out and the chain is put on. It is pulled around the tire, and then attached to the body. Important mechanisms are located here:

For this purpose, long slots under the spikes of the case are made on the plane of steel. Further, the mounting systems begin to vary. Electro-saw manufacturers solve the problem in their own way. For example, the tension is provided with a symmetrical spiral screw, like Champion, or a lonely spike, like Makita.

It is usually delayed by the key. But Makita has a special folding screw. It is good that it is part of the design, but users complain that the elasticity of the springs is reduced, and the head begins to hang out. Pay attention to what is said if you consider it important. It’s good if there is a rubber nest under the mentioned key on the cord.

But there is in addition to the on.duty mechanism of adjustment. During operation, the chain is weakened, and it would be inconvenient to constantly remove the casing, turning the screw. The mechanism on duty is implemented in different ways. For example, the champion needs to be pulled with a screwdriver, and the nest is located from the side of the canvas.

Sparky does not have a screw, but there is a large diameter plastic tuning wheel. It is convenient, located on the side. In the duty mode, pulling the chain does not take much time. In appearance, the wheeled is fragile, there are fears that the mechanism is prone to breakdown. When choosing an electric saw, pay attention to the on.duty tools for maintaining the tension of the chain.

So the friction coefficient is reduced, and heat release decreases. Users complain that Makita pumps easily fail, and the oil either stops serving or injects too quickly. To control the level on the lateral part of the electric saw, the observation window is located. The type of oil is indicated in the instructions. If during the cut of the logs the smoke from the tire of the electric pill appeared, it is recommended to stop work immediately.

The electric saw usually has two pens. The first is located in the front of the case on the left. Arched and durable. In this place there is a shield, an employee both to protect against flying chips and as a spare switch. In many cases, during the operation of the electric saw, the so.called reverse blow occurs: the tire with a moving chain bounces up towards the lumberjack. As a result, the shield hits hands and crosses the switch that breaks the supply of power to the engine. Electric saw stops immediately, blocking the possibility of an accident.

In this sense, all devices are designed the same, but the part has additional protection against seizing the chain. In practice, the electric saw refuses to cut thick wet logs. In the case of fatal locking, the motor will be saved from imminent death. The chance that the chain will get stuck on the tire minimal, but it is present. If it jams, then the gearbox may fail. Products of this type without additional measures are not recommended.

The back handle is designed for the right hand. Having taken the electric saw in your hands, try whether it is well balanced. Modern 2 kW models weigh a little more than 2 kg, which facilitates the work. Electric saw should lie freely in the hands, for convenient cutting. The technical data provides maximum log diameters. The size is limited by the length of the tire.

You can not touch the objects with the end of the working electric saw, in this case, the chain in the arc bounces towards the head of the master. What can end sadly. Similarly, you do not need to try to saw logs whose diameter exceeds the indicated in the instructions.

In the off state, the electric saw chain is hidden in the casing, removed during operation. The front case of the electric saw is equipped with plastic or steel teeth. They need to rest against the workpiece, and then rock the blade up and down. It’s easier to cut, and the teeth serve as a limiter from this side. The last thing we want to say is food:

The probability of a reverse blow

If you fully comply with safety rules, do not forget about the risk of a reverse blow that may occur from the accidental touch of the nose of the cutting part to the processed surface or to any other solid subject. At this moment, the user simply ceases to control the saw. it can easily be thrown in his direction, as well as towards others. Of course, most modern models are equipped with a special brake of the chain, which works when pressed on a special plastic lever installed on the case. However, situations with a reverse blow are very dangerous, therefore, it is recommended to comply with the following very simple rules when working:

• It is impossible to start sawing the cutting tire;
• You always need to monitor the position of cutting equipment;
• Very carefully carry out cut on the started cut;
• work only with a saw with a sharpened chain;
• Do not saw several blanks at once;
• Do not saw on the ground, since the cutting chain can enter the ground and collide with solid objects (stones, roots).

Maintenance of an electric saw

Do you want the purchased power tool to serve you for many years? You plan to use the electric saw as efficiently as possible and at the same time do not want to spend extra funds for technology care? In this case, our simple recommendations for caring for this tool will definitely come in handy for you. Before starting the service, an electric saw must be de.energized. First of all, it is necessary to inspect the saw tool of the tool. Make sure that the required amount of lubrication comes to the chain. check its level. If the oil is not enough, then you need to unscrew the lid and add the required amount. Next, check the tension of the cutting circuit. It is considered optimal when the chain fit tightly to the metal tire and it can be pulled out only two to four millimeters. If the chain needs a lift, then this can be done as follows: loosen the clamping element of the casing of the sprocket of rotation of the chain and slightly lift the tire tip. Then rotate the chain tension regulator, which is available on the case. We advise you to have several chains and change them in turn so that the wear of the teeth is uniform. If the chain is dull, then it should be sharpened. You can, of course, turn to professionals who will process the chain on the machine, but it is permissible to do this work and independently. To perform this operation, you will need a file and a special set for sharpening. In the process of sharpening there is nothing complicated, however, we advise you to first read how to do it correctly. there is enough information on the Internet on the topic of interest to you.

Buy an electric saw in the smallest configuration? So get ready for the fact that you will have to buy a chain and tire right away, and this is also additional expenses. Buy only branded components. then you will be sure of their reliability and quality. Also, do not forget that you need to stock up on oil to lubricate the chain and an extension cord, the size of which should be calculated based on the tasks set. We hope that our recommendations will be useful and you can easily operate your electric saw.