How to season a fishing line for a trimmer correctly in a mower. How to wind a fishing line for a trimmer to a trimmer coil for grass... • CIMFLOK.COM

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

How to replace a fishing line for a trimmer on a trimmer how to wind a fishing line for a trimmer for a trimmer for grass

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Read how to clean the air filter on the echo trimmer

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

Exclude spontaneous start,
Delete the battery (if used),
Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Read how to put a fishing line for a trimmer on a trimmer for grass correctly

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

Exclude spontaneous start,
Delete the battery (if used),
Place the tool on a comfortable site for work.

Remove the head of the head of the grass for the grass

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Replacement instructions. how to insert a fishing line for a trimmer

It should be noted that the coils in mowers can be different:

for functioning with one osik;
for functioning with two antennae;
The fishing line for the trimmer should be extended through the through hole, which is located inside the element.

And you should not confuse this part with an extension cord for a lawn mower on a coil, because despite the similar name these are two completely different elements.

Mini chainsaw is designed for simple work and people who prefer to hold the device with one hand.

This article will tell you how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here // MachinSpec.COM/Leszagotovitelnaya/Benzopila/Stanok-Dlya-Zatochki.html, how to assemble a machine for sharpening chains of a chainsaw with your own hands quickly and simply.

In the first version, wound the cutting element is very simple:

You’re Using it WRONG

On the inside of the coil element there is a fixing ear.
One mustache is inserted into it.
Refuel the nylon thread in the direction of the reverse rotation of the coil element.
You will need only 2 to 4 meters of fishing line. When the winding process is completed, put the small end of this cutting element outward and fix it in the groove that is necessary to fix the fishing line so that it does not spin during the functioning of the mowal.
If there is no special groove, then the end should be held with a hand so that the cutting element does not spin during the further collection of the element.
At the last stage, it is necessary to pass the outer end of the thread into a special hole located on the outer part of the element. After that, the coil can be inserted into a mower.

When the video works with two ends of the polyethylene thread, then it is necessary to take the following steps to refuel the fishing line for the trimmer to the lawn mower:

Inside, the coil will see how many recesses for winding are available (two or one). If one deepening, then both ends of the threads will be laid on this recess. If there are two of them, then the antennae are laid out separately. each by its own seizure.
It is necessary to rewind from 2 to 4 meters of polyethylene thread and pass two ends into the hole.
Wind both threads in one direction, reverse the drum.
When the entire fishing line for the trimmer is wound, the ends should be fixed in grooves or held with a hand.
Both ends are threaded in the ear from the outside of the clip body.
After that, the drum is assembled and inserted into a mower.

To insert a fishing line for a trimmer into a lawn mower in which the coil contains two grooves, you must use the previous option for refueling this polyethylene thread. In this case, each of the ends of the fishing line will be wrapped in a groove. All other actions similar to the previous process.

Coil element or video can have a completely different design, different from the previous two options. A fishing line for a trimmer can be extended through an ears, which is through and is located inside the coil. In this case, you do not need to disassemble the roller drum and manually wrap the plastic thread.

The polyethylene thread is threaded through the hole and rotates by pressing a special button. This button is located on the case and is intended for the operation of the equipment so that it is possible to produce a fishing line for a trimmer as it is worn.

Do not worry that the polyethylene thread is wound in the wrong direction, since it can spin in this design only in one direction.

Safety precautions

For quick and safe replacement of fishing line on a mowing coil, it is necessary to observe safety precautions. Before removing the coil, to wind the fishing line for a trimmer for a lawn mower, you need to turn off the equipment from power supply (if the braid operates from electricity). Here I want to mention the rating of electric lawn mowers by reliability that will help you choose a safe assistant.

Another important rule of safety that needs to be observed is pressing the lock button. You can find out its location on the equipment building using the operating manual. For example, the instructions for the operation of a hand gasoline lawn mower will be found here.

Do not forget that the cutting element must be adjusted. On the aggregate housing there is a button of tuning. If the process does not start automatically and weakening of the thread tension occurs, then the button is clamped, and the fishing line for the trimmer with force is pulled out of the coil.

It must be remembered that the replacement of fishing line in a lawn mower is an important process that requires responsibility. It is necessary to perform everything in stages, and only a special polyethylene fishing line for a trimmer should be inserted into a coil. An iron cable is not suitable for some high quality wire or even a reinforced fishing line for a trimmer.

Preliminary preparation

Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack bobber. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

CHAIN Trimmer Head !? REVIEW AND TEST #2

Coil with one working osik

The easiest option and a simple sequence of actions:

The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the fixing technological hole located inside the spool.
The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobbin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Instructions on how to promote a hand head on a trimmer is described below.

First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Frequent errors

Although the winding of the fishing line is a very simple task, many newcomers can wrap a fishing line for a trimmer incorrectly. The most common errors are presented below.

Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and they, accordingly, do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
In a hurry, some people do not observe the gas stations inside the coil and wind up the thread like it. This leads to the “departure” of the fishing line from the coil and can even cripple.
For winding, it is worth using only the corresponding fishing line for the trimmer. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also your type. You should not use the first fishing line for a trimmer for wrapping, which will not match the goals. For example, you do not need to use a thread on the young grass, if it is necessary to mow dry.
Do not turn on the device until complete winding and collection. Although this is obvious, some people do this in order to check if everything is done correctly.
In no case should you confuse the refueling direction, as it will overload the engine, and it will soon get out of the working condition.

Beginners are quite characteristic of mistakes, so it is necessary to observe the advice given in this article.

The choice of fishing line

In order to easily wrap a fishing line for a trimmer to a trimmer coil for grass, it is worth deciding on what tasks the garden tool will perform. The thicker the thread tucked into the head, the more difficult the tasks that it can complete. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can decide on the size, using the following methods:

get acquainted with the information set out in the instructions from the manufacturer;
check the suitability of the fishing line for use on your own, trying to insert it into the coil hole;
study the spool for information about diameters allowed for use.

Selection of fishing line for refueling a trimmer for grass can be carried out by engine type. So, for example, an overly thick thread can affect an increase in rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and timing of its further operation.

Avoiding negative consequences is easy. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line for a trimmer with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use the cord by 1.6 mm. A thread with a diameter of 2 mm, in turn, is used for engines with a power of more than 1 kW. It is worth noting that the cord for 2 mm is often used for winding on a bent mower. If the gasoline device has a straight shaft, the thread should be used 2.5 or 3 mm. The thickest fishing lines are installed exclusively on devices, the power of which is equal or exceeds 1.3 kW.

The last, but no less important factor is the type of fishing cross section. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several demanded cross.sectional options:

twisted-has a small margin of safety, which is why it suits exclusively for young grass;
Substitute. is characterized by sharp edges suitable for working on overgrown weeds;
Round. the most common section. Such fishing lines cope well with fresh grass, but they are not suitable for shrubs and dry ones;
rectangular, square and star type of cross section-due to low strength, are used to work on lawns.

The most durable and universal cord is a two.component fishing line for a trimmer with a round cross section, inside which the core is located. It is this thread that is suitable for the majority of work. It must be remembered that the use of fishing fishing line, ordinary wire and other third.party materials as a cord pose a danger to others.

Removing and disassembling the coil

In order to correctly wind the fishing line for a trimmer to the coil of a trimmer for grass, you must familiarize yourself with the structure of the trimmer head. It consists of a protective casing, a bobbin with a thread, a hull cover, as well as a spring that is present only in some devices.

Starting to disassemble the coil, you must completely turn off/de.energize the device. In this case, the method of work directly depends on the type of head. The first option is to conduct the following actions:

The user presses on fixers located on both sides of the cover.
After removing the lid, the spool is extracted. Some models may have a spring, which also needs to be extracted.
A screw is located in the center of the case, which should be unscrewed with a regular screwdriver.
When the fasteners are removed, it remains to remove the gearbox from the shaft, gently shaking the case of the product body.

The second option for removing the coil for refueling the fishing line in a trimmer for grass is to tighten the head for the gearbox shaft. To carry out such a procedure, many devices are equipped with a hole into which you can insert the tool. When the screwdriver is inserted, the user can only take up the product body and scroll it clockwise. It is noteworthy that this method, in contrast to the previously described method, differs in the simplicity of execution.

How to put a chain instead of a fishing line on a trimmer for grass

You can additionally “pump” the unit to mow not only grass, but also weeds and young growth. This does not require expensive tools or special skills. As they say, everything is brilliant just!

chain from the old chainsaw;
A cup bent inside, which is used to attach a trimmer for grass;
washer and nut;
vise, marker and ruler;
welding machine;
drill;
Metal for metal.

The length from the ends of the chain to the puck should be the same.

Additional recommendations for the replacement of fishing line

Before charging a fishing line for a trimmer to the coil, you should use several tips of manufacturers. They will be interesting not only to beginners, but also to experienced owners of trimmers.

These recommendations will help prevent people’s injury and extend the life of the equipment:

You can not wrap the thread with effort and tightening, in addition, use a large length than expected.
After replacing the fishing line, you should check the performance of the unit.
The lid should be installed to characteristic clicks. If at least one latch does not snap, the coil may jump out during operation.

Important! The mowing of grass should be carried out in special glasses and costumes, since small objects that can fly and injure others fall under the rotating parts of the mechanism.

How to choose a suitable fishing line for a trimmer?

For trimmers working both from electricity and gasoline, nylon fishing lines are suitable. This consumable can be used for both a hand tool and for a lawn mower on wheels. It is important to choose the right fishing line for a trimmer, as this directly affects the result of the work and the service life of the unit. Of course, in the proposed assortment of forests it is very easy to get confused, especially beginners. However, there are many tips from specialists and those who have already tried various options.

For an electric trimmer for grass with a capacity of less than 500 W, a thin fishing line for a trimmer with a diameter of 1 to 1.6 mm is suitable. She will perfectly cut the lawns with low grass. If the tool power is in the range from 0.5 to 1 kW, then it is better to give preference to a fishing line whose diameter will be 2 mm or slightly larger.

This will be enough to mow thin grass or grown weeds, but not too thick.

For gasoline trimmers, as well as motorcycle, you can not take a fishing line for a trimmer less than 3 mm. Such a thickness will easily cope with any weeds, dry stems, thick grass. A diameter of more than 4 mm is suitable exclusively for gas troops with high power. It turns out that a thick fishing line for a trimmer is necessary for powerful equipment. It is not recommended to use it for low.power trimmers, otherwise it will work poorly, constantly wound on the coil and create an additional load on the engine.

As a rule, in standard packaging is up to 15 meters of fishing line. However, to replace the string on the coil, about 7 meters long enough. It also happens that a fishing line for a trimmer is produced by bays of 250-500 meters. Be sure when choosing a string, you need to clarify the date when it was made. Too old nylon can be superior and become too brittle. If this happened, then you can soak the fishing line for a trimmer for a couple of hours in water, but it will not be completely the same.

When choosing an important parameter, the section of the string, which is of several types.

Round section is universal. It is used for mowing grass of medium thickness and density. When working can be unnecessarily noise, but it is not used too quickly.

Square or polygonal section is more effective compared to round. Thanks to the sharp corners, the stalks of plants are cut off at a higher speed and better.

Ribbed, twisted and star.shaped section is the most effective. Such a fishing line manages to mow the grass very quickly. And its main disadvantage is to quickly wear.

The fishing line for a trimmer for a trimmer for grass is made of nylon, which is durable, light, low price and wear resistance. To make the cost of the material even cheaper, polyethylene is added to it, but then the fishing line for the trimmer overheats faster. In thick strings there is a rod made of graphite or steel. Sometimes they are reinforced, which increases the strength and service life.

It is worth noting that the for two.component strings are higher than for standard nylon.

The device is in a mower

In the trimmer, the element on which the string is pulled is very simple. It is called the “coil”. Usually it consists of the upper and lower part (grooves), between which a partition with a deepening passes. It is on these grooves that you need to wind a fishing line for a trimmer. However, before it is extended through the recess.

Before pulling out the coil, you should twist a special button located directly on the housing of the lawn mower. Before changing the fishing line for the trimmer, it is necessary to remove the coil from the mowing.

It is easy to do this, but there are features depending on the configuration of the trimmer for the grass and the coil itself.

In small electronic braids, the motor and coil are in the lower part, and buttons are located on the sides of the bobbin. If you press them, then get the upper groove of the coil and part where you need to wind the fishing line for the trimmer.

In lawn mowers with a curved bar, which are not provided for a knife, the coils have special two.horned nuts. In such tools, you need to hold the bobbin so that it does not move, and at the same time turn the nut out of clockwise. It is she who holds the whole bobin, which after that is easy to remove.

Direct rods on which you can install a knife have a hole right under the bobin. To remove the coil, a screwdriver is located in this hole, the bobin is fixed. After that, you need to turn the coil on the movement of the clockwise and remove from the unit.

Sometimes clamps on the coil in the form of latches may occur. They must be pressed to disconnect parts of the coil. The option is also possible when the top and bottom of the bobbin are connected by thread. In this case, it is enough to take your hands on the top and bottom, and then twist in different directions until they develop.

Tips for choosing fishing line for a trimmer for grass

Coil. the main component of motorcycles. For a bevel of grass, it is equipped with a special fishing line. This very fishing line for a trimmer can serve you for a very long time, if you do not regret it (fishing line for a trimmer for a trimmer for grass. what you should not save on). Currently, you can find different cutting threads that differ in their cross.section, composition and thickness. Often a fishing line for a trimmer is sold in small or large skeins in specialized stores. If you want your mower to serve you for a long time, approach the choice of fishing line with full responsibility (because due to the wrong choice you can even break your device).

Never choose a thread for “save”. Having bought the cheapest and, obviously, the most low.quality fishing line for a trimmer, you can lose much more. As a rule, the best parameters are indicated on cheap (“Chinese”) fishing lines, but in fact they are completely different. The consequences of buying the cheapest threads can be both a breakdown of the thread and the fact that the lawn mower will fail. If the coil quickly fails, you will have to replace it again, which means you spend even more money.
Buy fishing lines only in specialized stores or from sellers, in which you are 100%sure so as not to be deceived.
Always check the authenticity of your fishing line. It’s no secret that the goods can fake, and the coils are no exception. If you decide to buy a high.quality brand thread that will last you for a long time, look for special holographic signs or codes on its package. With their help, you can easily check the authenticity of the fishing line.
In addition to the advice above, if you choose a high.quality brand for long work, choose a fishing line for a trimmer from German or Japanese manufacturers.
If your lawn mower or trimmer for grass has its own production of forests. no doubt, buy them, because the manufacturer took into account all the nuances in advance.
Do not forget about the fact that the fishing line for the trimmer should correspond to all the hardware characteristics of your motorcycles as much as possible so as not to cause its breakdowns.
It is best to buy 2 or 3 slices of fishing line intended for different purposes at once. One type of fishing line will be more effective in mowing fresh young grass, the second. in mowing stiffly overgrown, and the third will help you demolish all the gross.

When you have already bought a certain type of fishing line, be sure to follow the tips for its operation from the manufacturer. Thus, if you use a thread for young grass for dry.resistant, it will get out of the working condition very quickly, and you will have to buy a new one and replace it again.

How to put, wind and change a fishing line for a trimmer?

To do everything correctly and neatly, prepare a separate cut of the fishing line about 4 meters. The length may vary depending on the characteristics of your thread and the lawn mower itself. To find out how much fishing line you need, you can perform the following simple action: inside the coil, wrap the equipment to such an extent that it and the side protrusion of the coil are equal. At the same time, the equipment should not go out for the side ledges. What happened is the length you need, now you can make refueling. The length of the segment also depends on the thickness of the fishing line. the thinner it is, the more it needs, the thicker, the less.

Here is a step.by.step instruction on how to correctly refuel the equipment into the tip of your unit.

Then you need to take the second end on the other side and go too far. Gently approach him, while ensuring that the retreat is 15 cm.
Now you need to find out the direction in which you will wind the fishing line for the trimmer. Ignoring or incorrect execution of this item can lead to your trimmer for grass or lawn mower will not function normally. Inspect the surface of the coil to find out the right direction. In 99% of the coils, an arrow is drawn there, which shows the desired direction.
Instead of the gun-wiring pointer, there may be a letter designation (for example, Wind Line), which also indicates the direction. If you are not lucky, and there is no pointer on the coil, it will definitely be on the head. On each head, the direction of its movement is drawn, respectively, you need to wind in the opposite direction from what is indicated on the head.
After you have determined the direction of winding, proceed to the process itself. It is necessary to gently wind up (refill) thread on the corresponding grooves-undergraduates. Inside each end there is its own groove, do not forget to follow it. If suddenly they are not, put the equipment in the proper distribution order.
Follow the moment when almost the entire thread will be wound. When this happens, place in the side wall (special opening) the part of the part in which the protrusion is 10-15 cm, and then repeat this action with the second end, putting it on the opposite side.
Place the drum in its place, and then pull the ends of the thread, thereby taking them out of the walls of the coil. Now you can place the lid in your place.

The process of winding the fishing line on a motorcycle or a trimmer for grass is completed, now cut the ends of the thread, if suddenly their size does not suit you (or you were just mistaken in measurements). You can put on the drum already completely assembled on your unit. Now it can be used. Even a beginner can install a new fishing line for a trimmer on your device, this rarely causes difficulties.

If you are guided by all the advice presented, it will be as simple for you as mowing grass.

Sources:

https://agrohimtrans.ru/gazonokosilki/namotka-leski-na-katushku-trimmera.html
https://zetsila.ru/%D0%B7%D0%B0%D0%BC%D0%B5%D0%BD%D0%B0-%D0%BB%D0%B5%D1%81%D0%BA%D0%B8-%D1%82%D1%80%D0%B8%D0%BC%D0%BC%D0%B5%D1%80%D0%B0-%D0%B8%D0%BD%D1%81%D1%82%D1%80%D1%83%D0%BA%D1%86%D0%B8%D1%8F/
https://machinspec.com/kommunalnaya/kosilka/kak-namotat-lesku.html
https://proinstrumentinfo.ru/kak-zapravit-lesku-v-katushku-trimmera-pravilno-video/
https://stroy-podskazka.ru/trimmery/namotat-lesku-patriot/
https://echotool.ru/blog/articles/kak-namotat-lesku-na-katushku-trimmera/
https://homius.ru/kak-namotat-lesku-na-trimmer.html
https://stroy-podskazka.ru/gazonokosilki/leska/
https://stroy-podskazka.ru/trimmery/leski-dlya-benzinovyh/