How to use a trimmer for grass. Description of a trimmer for grass for haircuts of a lawn

Proper operation of a trimmer for grass for grass

In every summer village, village, suburb and in the city itself you can see these devices: they work tirelessly, aligning the lawn grass, cleansing the space of squares and parks, gardens and gardens from thickets of burdock, wormwood and weeds. The noise and crackle from the trimmers are heard from the beginning of summer to autumn, until the growth of the grass is so much so that it will no longer need to trim it. Automatic braid for grass deserved its popularity for the simplicity of the device and operation. It is easy for her to use, it is easy to care for, and in case of breakdown it is not possible to easily fix it without difficulty. The article will just tell you how to use a trimmer for grass correctly.

As with any other technique, in working with the trimmer there are rules. First you need to make sure that the main nodes and assemblies: screw, rods, handles and motor. If the device has not yet been assembled, then it should be correctly assembled according to the instructions.

Gasoline unit

In the case of a gasoline trimmer, it is necessary to check the gearbox for lubrication. Also, do not forget to add lubricants to the fuel tank, if the instruction manual is evidenced. As a rule, gas and oil are mixed in a ratio of 45 to 1, but these indicators may vary depending on the model and manufacturer, so you should carefully study all the technical requirements for the device. The fuel container must be filled on the very neck. If all technical fluids are flooded, then you can try to start the device. But it’s not worth mowing right away, it will be better to let the trimmer work without load so that the engine works to the flooded fuel. A few minutes will be enough, after which you can give the motorcycle full load.

Elektokos

With an electric trimmer, everything is much easier. Having made sure that the gearbox has the required amount of lithol, you can start work. No additional measures are required. Unless it is necessary to make sure that the carrying does not run on the path of mowing in order to avoid possible damage.

When the device itself is ready to work, you should make sure that there is nothing around that could interfere with the work. If possible, the estimated mowing area should be cleaned of snags, glass, stones and other solid objects that can damage a knife or fishing line for a trimmer.

It is better if other people do not approach the trimmer while working. Usually the recommended distance is at least 10-15 meters in order to avoid small debris (mulch) in the eye and on the face.

Depending on the upcoming work, you need to choose a nozzle for a trimmer for the grass: a screw-knife for weeds and hay, a fishing line for a trimmer for lawn grass or a disk saw for shrubs. Mowing should be in the opposite direction from people, if possible, moving away from buildings and buildings. You should not get too close to the fence and other designs, since the fishing line for a trimmer can catch on sharp edges, and the screw-knife will bend if it accidentally offends it a hard object.

The preparation of the device itself will not take much time, all modern models of devices are designed to facilitate and simplify their operation, starting to work in the shortest possible time.

We run up a gasoline trimmer for grass

Most often, the running.in is used in a motorcycle (trimmer for gasoline grass). The running.in is the operation of the engine at low speeds, without loads. To run, it is necessary to start a motorcycle and let it work at idle. It is best to produce the first mowing with a fishing line, since when mowing lawn grass is a less high load on the engine than when working with hay or shrubs.

The load must be increased gradually, in stages increasing engine speed. If you start operating with high speeds, the engine can be poorly developed, which will affect the entire further operation of motorcycles.

Do not produce the entire temporary resource during the first engine start. It will be best after working at idle by idle for 10-15 minutes to mow, then drown out the device and let it cool a little. Use a motorcycle system carefully, without sudden movements, in order to avoid collisions with solid objects (stones). The stab on the stone can poorly affect the work of the unfortunate nodes. In some cases, backlash, noise and hum during operation appear. This can be easily avoided if the trimmer for the grass is correctly running.

We start with safety precautions

From the protective devices, glasses and gloves recommended according to the instructions will not interfere with the instructions, but the most important protection of the legs. Cutting tool, especially if mowed with a gasoline trimmer with metal knives, rotating with huge revolutions, picks up garbage, pebbles and cutting of vegetation, flying away at such a speed that they can cause injuries to a person. Therefore, it is desirable to work in trousers and closed shoes or boots.

As for the protection of the ears, the tangible need arises for this only for the most “loud” benzotrimmer. based on a two.stroke engine. They are usually equipped with special headphones with the headline necessary to reduce sound pressure on the eardrum.

Preparation of a trimmer for grass for work

Preparation of a trimmer for grass for work begins with checking the condition of all parts and assembly according to the instructions. At the same time, you need to make sure that there is a lubricant in the gearbox, and in the crankcase of a four.stroke gasoline trimmer for grass there is enough oil. Fuel, depending on what type of engine, two- or four-stroke, is a mixture of gasoline with special oil in a ratio of 40–50: 1 or, accordingly, pure gasoline. After the fuel tank is filled, it remains only to open the tap and the trimmer for the grass can be tried, not forgetting that before the start of the kosba, it is necessary to work at idle for 2-3 minutes.

With an electric battery tool, everything is simple. after checking the availability of lubricant, it is enough to insert a charged battery into the corresponding nest so that it is ready to work. If the tool is powered by a power grid, then you will need an extension cord to the expected haircut location. The wire must be placed outside the zone of the possible action of the trimmer knives for the grass.

The site should be maximally freed from foreign objects: glass, stones, wires, snags, etc. D. The presence of people is closer than 15 meters is also undesirable. Depending on the capabilities of a particular trimmer for grass and expected work, you need to select the appropriate cutting nozzle. You can use a mowing head with a fishing line for grass, metal knives for weeds or hay harvesting or a shrub saw. Powder should be planned to move, moving away from buildings and people.

Choose a suitable nozzle

In addition to its product, the manufacturer usually provides several mills (usually 3).

To work with soft grass as a cutting element, a fishing line for a trimmer is used, wound on a drum. Speed ​​of 9,000 revolutions per minute allows you to quickly process even a large lawn.

For more rough grass and thickets, one of the metal knives can be used, which differ among themselves by the number of cutting teeth.

For mowing thick shoots, reeds, young shrubs, a disk with 40 or 80 teeth is designed. Corn, dry weeds with thick stems, you can mow three- and four-lobed milling.

And in order to put beveled grass in the rolls, a knife with 8 blades is used and a special crest is attached to the braid itself.

And now more about how to install a cutter. The place of fastening of the cutter is called a gearbox. On it, first you need to fix the figure washer using a hexagonal key.

Then put on a knife, combining the holes in it with a protrusion of the puck. After that, you need to install the upper figure washer on the shaft and tighten everything with a nut.

Here you should pay attention to the fact that the thread on the shaft is left, so you need to tighten the nut (like screwing the mowing head) counterclockwise.

To squeeze the nut to the stop will help the key, which is also in the delivery kit. You can replace the cutter by doing all the operations in the reverse order.

We season with a motorcycle

To refuel the chainsaws, not pure gasoline is used, but a working mixture that needs to be prepared in certain proportions.

The combustible mixture consists of gasoline with an octane number of 95 and high.quality oil intended for two.stroke air cooled engines.

The proportions should be 25 parts of gasoline per part of the oil.

It is better to mix components in a separate container, from which, using a funnel, then pour the mixture into a fuel tank.

After refueling braids for grass, you need to wipe the entire surface dry in places with traces of spilled liquid.

The trimming of the bush

As you know, a trimmer for grass can be used not only for mowing grass. But also for trimming thin branches. For example, at the bushes. For this, as a rule, the working part of the unit has to be put in a position close to the vertical. As a result, the probability of capturing from the surface of the earth and the subsequent emission of small stones and garbage is great.

So that this does not cause any troubles, it should be remembered that garbage disclosure always occurs to the left side. Therefore, it is better to be located during work so that flying garbage is not directed at people or pets. But the perfect option would be their complete removal from the zone of your work.

However, the possible harm to people and animals is not the only potential trouble at all. Garbage and stones on the basis can damage the tool itself. Therefore, before starting work, it is advisable to remove them from the surface of the soil. At least the largest and most dangerous items.

Preparation for work

Before the first turning on the trimmer, a certain preparation is needed to avoid failures, breakdowns and injuries. First you need to make sure that all parts of the device are whole, without cracks and dents. Often, devices are sold in disassembled form, so they should be assembled in the manner indicated in the operating instructions. In addition to verbal descriptions in the documents there are schemes and pictures. Further actions for technology of different types are very different.

Setting up and the first launch of a gasoline unit

First you need to check if there is oil in the gearbox and, if necessary, add. Many models of trimmers need to add lubricants to the fuel tank or a separate tank. What should be the ratio of “gasoline: oil”, it is better to know from the device for caring for the device. Then you need to fill the gas tank to the top, after which you can start a gasoline trimmer for the grass, performing the following actions:

• close the air damper;
• turn on the ignition;
• In the presence of a manual fuel pump in the model, you need to press the leather lever several times until the fuel is visible in the primer;
• put the device on a solid even surface;
• Smoothly pull behind the trigger cable until the appearance of resistance;
• pull the cable abruptly 3-5 times.

Important! You can’t mow a trimmer immediately after starting. It is necessary to give the device to work for several minutes at idle, so that the engine will get to the fuel mixture.

Setting and launching an electric trimmer for grass

First of all, you need to charge the batteries or check the performance of the electric cars, as well as the integrity and length of the wires. In the presence of a gearbox, lubricate it with a lithol. Then you can turn it on and turn off the trimmer for the grass several times, but do not start mowing. The device should start quickly. If there are no problems, you can proceed to the run.in electrocos.

Useful information! At the first launch of a new trimmer for grass, you need to work with a fishing line and mow soft grass, for example, cut a lawn.

Playing a trimmer for grass

The revolutions on the gasoline unit must be increased gradually to let the engine work to combustible. For the first time it is better to work without stopping no more than 10-15 minutes. This is also necessary for a person to get used to the weight of the device with a full tank of gasoline, find a convenient position for hands and the correct tilt for the body. After test starting, you need to turn off the motorcycle and let the engine cool.

An electric trimmer for grass can be tested on lawn grass. For the first time enough for 5 minutes, after which the device needs to be turned off.

How to mow grass with a trimmer with a metal knife

As the border of the mowing area moves, move the fuel and the bag.

If the grass was setting down: you need to hand the steering wheel forward and mow to the left with an inclination by the handles to the left (sector ~ 11 hours) and the right with the tilt for the handles to the right (sector ~ 1 hour), and do not rush!, to mow the grass cleanly and so as not to “dig” the earth.

During the mowing of grass (and turns), do not forget to look around!:

• To notice the gesticulation of others, drown out the motor and remove the headphones,
• So that closer than 15 m children, animals, spectators and assistants do not come up, t.to. When a metal knife in the grass collided with a motionless object, a trimmer for grass or a lawn mower (motorcycle) can be strongly thrown to the side or expanded back, and a trimmer for the grass rotates at a speed of up to 10,500 rpm. And he is able to cut off his hand or leg.Also, when the grass is mocking the trimmer from under the knife, various objects (crushed stone, glass, garbage) can fly out and ricochet).

How to mow grass with a trimmer (more about the mowing technique)

The engine revolutions when the trimmer mowed depending on the load on the engine. the thicker the grass and, of course, is heavier than the engine, the bolder you need to open the “hole” (throttle in the diffusor of the carburetor).

Work speed of the engine during the mowing of grass with a trimmer try to keep constant (slightly higher than medium). or less gas. only depending on the overall load on the engine. No need to completely discard gas (and immediately acceleration again) with each wave of braids for grass. And the clutch is not for long, and the edges on the drive shaft can “overtake”, and the overall wear of the trimmer for grass (motorcycles) increases sharply.

Before mowing grass, we find out the parameters of the site

(to know which knives to take, how much fuel and time are needed)

• Grass density;
• The hardness of the grass;
• the splendor of the grass;
• wovenness of grass;
• (The height and thickness of the grass are not important)
• the boundaries of the site;
• what irregularities (how to come in);
• the presence of hidden obstacles (remember)
• that not cut (bushes, flowers, seedlings).

To mow grass in the summer is a disaster, and not just homework how to use a trimmer. If your yard or site is strongly overgrown with grass, you can scare you, but this part of the article will help to figure out how to mow grass with a trimmer easier and less irritating.

How to use a trimmer

Tips on how to mow grass

• Mowing grass when it is not very large. This will allow you to cope with work much easier and faster than if you mow a strongly overgrown lawn or yard. A large mass of grass, weeds, plants and trimmer will be hard to grind. In addition, a lot of chopped grass will lie on the surface, which must either be cleaned, or wait until it dries, or while it becomes compost, which is not very beautiful and can cause various diseases of the grass.
• Avoid mowing not grass, but fences, stones, bricks, any other hard objects, as this will greatly accelerate the wear of the fishing line and it will require its more common replacement.
• Some will have to wear an orthopedic corset (although it may seem stupid). Back support allows you to maintain performance longer and feel more comfortable.

Warning how to use a trimmer

Trimmer for grass, like a twin.franc grinder, chainsaw or garden tractor is unreasonable for what it is not intended for.

Keep a trimmer for the grass away from yourself so as not to cut off your fingers or leg.

Do not mow a trimmer in water or wet grass. If you have an electric trimmer for grass, you may hit an electric shock. If you have a gasoline trimmer for grass, you can pollute water and grass with fuel and exhaust gases.

You will need things to mow grass

• Pants. Preferably strong working jeans without holes. You can mow grass somewhere, so if your legs are not protected, soon you will feel how several thousand ants crawl along your legs and bite you. Sometimes a weed can scratch to the blood or stuck strongly, thrown back on the mower.
• Gloves. wandering, leather, it does not matter. If you mowed grass without gloves, then by the end of the kota you will not be able to move even a little finger without pain. The weight of the grass through a trimmer for the grass presses in the hands and abrasions and scuffs will appear on their hands if they were not in protecting gloves.
• Protective glasses. you cannot mow grass with your eyes closed, because small pieces of grass fly in the face. One good hitting your eyes will convince you that protective glasses are mandatory. This applies to one of the main rules how to use a trimmer.
• Have a sufficient amount of drinking water at hand. Even if you think it will not be hot, think again. You need to mow grass with a vibrating trimmer for a long time.
• Have a spare fishing line for a trimmer or a seasoned trimmer head to replace if it ends.
• If you have an electric trimmer for grass, you must have an additional extension cord. If you have a gasoline trimmer for grass, you must have a supply of fuel.
• Rake to rake mowed grass or weeds.
• Headdress if you work in the sun.
• High boots (pants are best tucked into boots).
• If you plan to work at dusk or later, make sure that you have a spray from insects and a lantern.

Cutting technique

It seems that the uniform haircut of the grass should be simple. draw a trimmer for grass over the grass, and the fishing line for the trimmer will cut it to the desired length. But this is not the best approach and will actually lead to the appearance of a bald man on the lawn. To turn a naughty tool into a reliable machine, it is important to rely on knowledge.

• The ends of the string are a place where the maximum incentive force is concentrated. At the same time, the faster and freedom the movements will be, the easier the process will go. Processing under the cone. Gives the lawn a beautiful view, the technique is especially spectacular along the roadsides, near the fence or trees. Keep the tool so that the string hit the grass at a slight angle.
• Framing. Where the surfaces are almost parallel, say, between the path and the roadway, I want to emphasize the edge. Therefore, we turn the trimmer for the grass so that the string is vertical. Then conduct a tool on the cutting path.
• No need to try to use all techniques at once. If the lawn has never been cut, then first you need to free it from garbage, then trim the grass to one length, and only then take it behind the edges.
• Kosim with a trimmer. If you have to work in tall grass, then you can use this just reception. This means that the tool should move along the path of the letter U.
• Screed. Another technique that is used to remove grass growing on the tracks in cracks. Tilt the tool so that the tips of the strings simply slide along the road surface, then move into the base of the weeds, cutting them to a solid surface. But be careful: tilt the tool too strongly, and you just tear a fishing line for a trimmer. Accept too sharp angle, and the fishing line for the trimmer will not be able to cut the grass evenly.

Trimmer care after work finishes

As soon as you finish cutting the grass, you will need to bring a trimmer for grass in order. First of all, cleaning along the lawn may be required. To do this, use a broom or broom, collect all the garbage and cut grass. If the area is very large, it is better to use a blower for leaves. This will greatly facilitate the work.

After that, you will need to put in order a trimmer for the grass. Remove all the grass that could get stuck in the casing, wipe all the cutting parts with a soft cloth. The battery trimmer for the grass is placed for charging, gasoline is additionally seasoned. Storage is carried out in a dry room.

Technique of work with fishing line and disk

The technique of work with a trimmer with a string and a disk has some differences. So, the fishing line for the trimmer cuts the grass with the very end, but with too fast the movement is used for the entire length. As a result, the stems are not cut, and the grass is wound on the cord, which is why the engine is overloaded. Therefore, you need to choose the optimal wiring speed. In addition, when mowing high and hard grass, a fishing line for a trimmer is consumed faster than when cutting the lawn.

On a note! If you need to process the slope of the hill, its peak should always be on the right. You need to rise gradually at a distance equal to the width of the scope.

There are several simple recommendations, the implementation of which will make mowing more efficient and effective.

• It is convenient to bite the garden paths, flower beds and the edges of the Lujaiks with a trimmer with an engine below. The plane of rotation of the coil of such a device can be placed perpendicular to the ground.
• Thick thickets, large weeds, bushes must be mowed with disks or special nozzles.
• When cleaning large areas, the device must be tilted to the left, in the direction of scope.
• To mow grass around flower beds, shrubs and other objects, you should rotate the head of the trimmer for the grass with a casing to them. So it will turn out to bake objects themselves and not damage them.

It should be remembered that the bobbin or the disk should not touch the ground and any obstacles except grass and branches that need to be cut off.

Care for the device

In order for the lawn mower to serve for a long time and properly, you need to perform a number of activities to care for it.

• Trimmer for grass must be stored in a dry room.
• After each use, the device must be cleaned of grass and litter.
• Air filter and a cooler radiator grille on the engine of a gasoline trimmer for the grass must be periodically cleaned by the method described in the instructions for the technique.
• It is necessary to monitor the presence of lubrication in the gearbox.
• The wires of electric trimmers should be intact, without creases and cracks in isolation. You need to include devices in the network only through groove outlets.
• All cables after use should be reelled.

If the gasoline trimmer for grass is not needed for a long time, it should be empty of the tank, let it work at idle to combat fuel residues, grease the engine. The composite bar must be disassembled, and the joints should be treated with preserving lubricants to prevent the appearance of rust. All nuances of storage and care are described in detail in the user guide, which can be downloaded in case of loss.

Gasoline gas mowing gasoline with butter

Before mowing grass with a benzo.leggos, it is necessary to season the tool with fuel. As fuel, gasoline with butter is used. However, take into account that mixing gasoline with oil is needed only for two.stroke engines. Four.stroke engines operate on pure gasoline, since their design has a separate container. oil crankcase. There are no 2-stroke gas crankcases in the design of the 2-stroke gasolimers, so you need to pour exclusively gasoline with oil into the tank.

As gasoline, it is recommended to use AI-92 brand fuel. In order not to make a mistake in choosing, you need to read the instructions offered by the manufacturer. Often, most manufacturers recommend using the AI-92 brand fuel, and only some recommend filling AI-95.

Gasoline must be diluted with a small one in a proportion of 1 to 25. This means that 40 ml of two.stroke oil must be added per 1 liter of gasoline. However, not everything is so unambiguous here. The proportion 1 to 25 is universal, but each tool model has its own values. These values ​​are also indicated by the manufacturer in the instructions. details about how to properly dilute gasoline with butter into a lawn mower is described here. After breeding gasoline with butter, pour a full tank, and start work.

It is interesting!If a four.stroke lawn mower is refuel, then pure gasoline must be poured into the tank, and engine oil is added to the oil container to the maximum level.

Preparation of a trimmer for grass for work

Preparation of a trimmer for grass for work begins with checking the condition of all parts and assembly according to the instructions. At the same time, you need to make sure that there is a lubricant in the gearbox, and in the crankcase of a four.stroke gasoline trimmer for grass there is enough oil. Fuel, depending on what type of engine, two- or four-stroke, is a mixture of gasoline with special oil in a ratio of 40–50: 1 or, accordingly, pure gasoline. After the fuel tank is filled, it remains only to open the tap and the trimmer for the grass can be tried, not forgetting that before the start of the kosba, it is necessary to work at idle for 2-3 minutes.

With an electric battery tool, everything is simple. after checking the availability of lubricant, it is enough to insert a charged battery into the corresponding nest so that it is ready to work. If the tool is powered by a power grid, then you will need an extension cord to the expected haircut location. The wire must be placed outside the zone of the possible action of the trimmer knives for the grass.

The site should be maximally freed from foreign objects: glass, stones, wires, snags, etc. D. The presence of people is closer than 15 meters is also undesirable. Depending on the capabilities of a particular trimmer for grass and expected work, you need to select the appropriate cutting nozzle. You can use a mowing head with a fishing line for grass, metal knives for weeds or hay harvesting or a shrub saw. Powder should be planned to move, moving away from buildings and people.

How to use a trimmer for grass with a knife correctly

No matter what knife you use, always keep it so that it is parallel to the ground. Adjust the belts so that the trimmer for the grass is conveniently located in this position, while part of the rod behind the handle rests on the shield on your thigh.

Knives can be used only on a trimmer with a straight shaft. This means that the knife rotates counterclockwise. And this means that it is best to cut the left side of the knife and move the head of the trimmer for the grass to the left.

If you cut the right side of the knife (especially the right front side), then a rebound (impetus) of a knife or as the Americans say Kickout. The rebound (impetus) of a knife is a quick jerk or jump for the grass, as if he hit the barrier and bounced. It can be unsafe.

Haircut of various types of vegetation

In addition to holding the knife parallel to the ground and cutting more dense thickets with the left side of the knife, there are some tips that should be taken into account for each type of vegetation that you may encounter:

Grass and weeds

To cut the beams of herbs and weeds, make sweeping moves forward and back with long arcs, as if you used a braid. Keep a trimmer for the grass so that the knife barely soars above the ground.

Dense shrub

Cutting thick, thick bushes, starting from the base of the plant, is not the easiest way. Instead, start by raising the knife to about the waist level, holding it parallel to the ground. Slowly lower it until the knife is right above the ground. Never raise a knife above the level of the belt.

Small trees and seedlings

A trimmer for grass with a saw can be used for cutting trees with a diameter of up to 2.5 cm. For trees of larger diameter, use a chainsaw.

Keep a trimmer for the grass so that the knife is at an altitude of 5-15 cm above the ground. Take a stable position and press the left side of the knife to the right side of the tree. Cut evenly, without shocks.