How to use Champion gas troops correctly. We get to work

Instructions and rules for safe work with a gas station. trimmer

Owners of summer cottages and country houses are familiar with the problem of maintaining the personal territory in aesthetic form. A lot of effort is spent on mowing the grass and cutting the lawn. Automation of such processes help electrical and gasoline trimmers for grass.

Consider one of these devices closer.

Gasoline braid device device

The weight of the entire device is about 8 kg, which is quite difficult to hold on the hands. Therefore, the unloading belt-rug belt with a protective pad and regulators is included with the scope of the scythe.

The grass braid is designed for mowing grass and small shrub in personal plots.

As you know, grass can be mowed in different ways. folding it in rolls or simply rolling it out. In addition, the grass is different. soft or rough, with thick stems, shrub.

How to start a lawn mower properly?

Regardless of the type of action, there is a strict order that must be observed, that is:

Inspection and verification

Any trimmer malfunction for grass can be a serious danger.

Poorly tightened bolts fixing the clutch bell to the engine can lead to rapid abrasion of clutch pads, and any leak of the fuel system often leads to ignition and burns or fire.

The weak tightening of the gearbox bolts can lead to the fact that the rush shaft bar will jump out of it and the trimmer for the grass will stop working. Weak tightening of bolts fixing the handles can lead to involuntary lowering the shaft and damage to the cutting tool.

Therefore, before any launch, you need to at least briefly inspect the device in search of defects. This is especially true for any first launch, it does not matter, after the purchase, or after storage. During the working starts, it is permissible to inspect only the fuel system for leaks.

One of the most important stages of verification before any launch is to determine the amount of lubricant in gearboxes and a drive shaft, for which you need to disassemble a trimmer for grass and remove both gearboxes from the shaft.

So you will evaluate the quantity and condition of the lubricant not only from the side of the gas station, but also in the area of ​​contact of the shaft bar with the gear of the gearbox.

Also, once every 2-3 weeks, check the amount and condition of the oil filled into the crankcase of four.stroke engines, if the device will work with a low level of oil for a long time, then the probability of jamming of the crankshaft is likely.

The gas station is fuel

This operation has to be done after purchasing and winter storage, as well as during the termination of work caused by the production of gasoline. Four-stroke engines are seasoned with pure AI-92 gasoline, and two-stroke with a mixture of fuel and special oil, which we talked about here.

Remember, if you refuel a two.stroke trimmer for grass after winter storage, be sure to drain the old fuel from it, because it has already lost the lubricant, so the crankshaft bearing and cylinder.piston group will work without lubrication.

Launching a benzotrimer

Regardless of the type of launch, there are 6 actions that have to be performed always:

• fuel pumping;
• the transfer of the air damper to the “Launch” position (“Closed”, “OFF”);
• the transfer of the switch to the “inclusive” position (“VCL”, “on”);
• pressing and fixing the gas key;
• the jerk of the starter cable with the choice of free move;
• transfer of the air damper to the “work” position (“open”, “on”).

The first 3 points from this list can be performed in any sequence, but you can pull the cable of the air starter only after them. Neglecting fuel pumping will lead to the fact that a hand starter’s cable will have to pull the moving piston of the motor to pump a sufficient amount of air that sucks from the carburetor fuel.

The neglect of the air damper will lead to a strong rethink of the mixture, which is good for a running engine and extremely bad for starting, because such a mixture is well ignited only inside the heated cylinder.

After the air damper is transferred to the closed position of the incoming air, it is not enough to operate the motor at idle, so click and fix the gas key (accelerator, engine speed regulator). The button for turning on/off the motor blocks the operation of the ignition system, so before starting, transfer it to the “inclusive” position.

If you do not transfer the switch to the right position, then the voltage will not come to the candle, which means there will be no spark that ignites the mixture in the cylinder.

After the engine works, transfer the air damper to an open position, because the highly re-enriched mixture is good for starting, because it is flammable even in the cold cylinder, but due to lack of air, the fuel does not burn out completely.

An attempt to mow grass with a closed air damper will lead to a sharp drop in the power of the motor and a strong heating of the valves, so the long work (tens of hours) leads to the gap of the valves or damage to the laying of the cylinder head head.

If the motor does not start or works incorrectly

The reasons that the motor does not start with a two or four jerks of the manual starter cable can be:

Most often, this is due to the incorrectly executed trimmer for the grass, when the procedure is violated or some important point is not executed, so the launch is quite correctly carried out and the motor will work. If the mower is poorly started after storage, then most likely, old gasoline is exhausted, so it is enough to change it.

If the trimmer for the grass was not served for several seasons, then the poor launch can be due to dirty air or fuel filter, so it is enough to rinse or replace it.

If all actions are performed correctly, but there is no positive result, contact the workshop or independently diagnose or repair.

How to put on and hold it correctly?

The quality of your work also depends on what technique you use. For the right technique, you need to be able to hold the unit, and for convenience to wear it correctly. The fact is that not all trimmers for grass are equipped with a shoulder belt. If he is, then it needs to be worn so that you are comfortable. There are models of devices whose belt can be inconvenient, so try to put on a trimmer for grass as convenient as possible how it will succeed.

During long work, it also happens that pain in the back and muscles arise, so the most convenient tool can reduce the number of such troubles as conveniently as possible.

Another function is to adjust this belt. On better models, its convenience assigned a special role and made special positions that will allow the manager of a scythe not to experience inconvenience. You can adjust the belt in height, choosing the necessary for yourself.

Now let’s talk about how to hold the unit correctly. Various types of trimmers have different handles. For someone it is made in the form of a bicycle steering wheel (which ensures the distribution of the load on both hands). On some units you can see the handle of the letter D. The bicycle option must be held with two hands, and tight.

Despite the presence of rubberized handles, it is better to rely on yourself and not hope that they will not slip. Keep the handle in the shape of the letter D with one hand, and with the palm of the palm to provide a large capture area. This will give you full control over the handle, which will positively affect control.

Rules of mowing

In order to cut the lawn with high quality and quickly, you need to observe the equipment and know some features that will save your time and effort. You can work faster, now we will tell you how.

Divide your site into zones. This will help you understand how much you will need to complete. Also, you will have no misconceptions in whether you have already worked here and do you go through the second again. For the first time, the lawn is mowed at a level of 4-5 cm, gradually reducing to 3-4. Install the norms of mowing yourself. You can leave more, smaller. It all depends only on you.

The disadvantage of electric trimmers is that if you mow vegetation during dew, then water can enter the motor of your technique.

If the motor is located below, then the probability of moisture will be even higher. It is also not recommended to work with a trimmer during the rain all due to the same reasons. Entering water can cause a short circuit, which in the future can develop into a malfunction of the unit. Therefore, it is better to wait for the weather more favorable for work.

It is recommended to work clockwise. It is this direction that will leave the grass you mowed by the outside of the entire mowing site. While hold the coil at least 5 centimeters. This is a safe option for a mowing that is good for those who have recently started using such an inventory. If it comes to work at the fence or other places where only a small part is required to mow, then use the edge of the fishing line. This will contribute to the fact that the engine will not overload and wear out.

Under hay

Use as a cutting element of a disk, because meadow vegetation is tougher than usual. It is better for the fishing line precisely for hay by cutting dry grass better. Thus, the grass will not get stuck on the fishing line, which can lead to the poor operation of the engine. Hay does not need to be cut small, it should be quite high, so try to mow hay under the root.

Even lawn

To create a flat lawn surface, try to process the greens of garden equipment as low as possible. So all the grass will be the same in height, which will make the coating even and beautiful. Do not forget about the inclination. For the best result, tilt the device at least 30 degrees to the surface of the grass. It will cut the grass as low as possible. Any other irregularities can be removed using garden scissors if they are available.

Spinning high grass

Particular attention is required here. High grass needs more thorough processing than simple. The fact is that there is an effect of wrapping vegetation on the reel. In this case, the grass remains on it and does not allow the mechanism to rotate in full power. This noticeably inhibits the process and reduces the number of revolutions.

So that this does not happen, go through the way in several stages. Gradually cut a certain amount in height, passing lower and lower along the stem.

As a rule, in high green the base of the stem is much thicker and stronger, so in addition to winding you can damage the cutting element with hard stems.

It is also necessary to take into account the fact that if your technique works recently, then mowing high grass may be even more difficult. Therefore, do not work for a long time so as not to give the motor a particularly large load. It will be enough for 15-20 minutes with a break for 15 minutes. Since it is better to mow grass in several stages, do not forget about the grass collector. He will begin to clog very quickly, this will lead to problems with the tool. Clean completely so that not too little time passes before the next cleaning.

How to mow a trimmer with a fishing line correctly?

The mowing of the grass with fishing line (cutting string, cord) differs from the same operation, only performed with a knife or saw disk.

This is due to the fact that the trimmer cord affects the vegetation differently.

Therefore, we compiled a detailed instruction that will help you use the trimmer for the grass correctly and competently mow any vegetation fishing.

Stages of mowing

The process of mowing grass, that is, the implementation of certain movements by the trimmer, is only a part of a more complex process, which includes:

Therefore, we recommend reading the articles in which these actions are highlighted, that is:

The choice of fishing line

For an effective haircut of the site, you need to choose the right cord in shape and size.

The string of irregular shapes will also mow vegetation, but in terms of speed and quality will yield to the one that better corresponds to this particular vegetation.

When choosing a size (diameter or section), one has to take into account the following. the thicker the cord, the better it copes with its task, but the stronger the load on the tool.

Too thick string will break the gearbox and shaft bushings, and in particularly unsuccessful cases can greatly damage the trimmer for the grass. Detailed information on how the coil works and the instructions for choosing the cord you will find here (which line for the trimmer to choose).

Coil winding

To charge a fishing head with a fishing line, insert a cord of sufficient length into it and, leveling both sticking pieces, then tighten the button in the corresponding direction.

Remember, the direction of rotation of the shafts of trimmers with a straight and curved bar does not match, so different coils are installed on them. Be careful, a fishing line for a trimmer is drawn on the head of the head, indicating which way you need to twist the button.

To charge a semi.automatic head, act like this:

• Squeeze your fingers with fixers holding the lid, then remove it;
• Pull the spool;
• Remove the remains of the old fishing line;
• Wrap a new string, the winding direction is indicated on the spool, lid and coil body;
• insert the rogue into the housing;
• bring both ends of the fishing line outside;
• put the lid to the click so that the latches fix it.

The method of charging a mechanical coil depends on its type (in some cases, you will have to wrap the cord on the removed head, then put it on a benzo- or electrocos).

A detailed description of such trimmer heads and tips on winding the fishing line on them will be found in these articles:

Preparation of the site

The trimmer cord is made from various types of nylon, and this material does not differ in high strength or abrasion, so prepare the site before cutting.

To do this, go through its territory and remove all the garbage, from plastic bottles to large stones or pieces of reinforcement.

If any obstacles could not be removed, then you will mark their perimeter in order to mow most carefully along it, otherwise, with the mowing of grass in this area, you will spend a fishing line for a trimmer much faster, and there is also the possibility of damage to the trimmer for the grass.

The choice of equipment

To understand what equipment is needed, it is necessary to disassemble the processes that occur in the process of mowing grass with fishing line.

Moving at high speed, the cord crashes into the stem or foliage of the grass and cuts them off, after which the upper part of the plant falls to the ground. Sometimes the falling fragment falls under the fishing line for the trimmer and cuts it again, maybe even several times.

Each blow of the cord on the fragments of the grass leads to spraying the juice and flying up small fragments of crushed vegetation, which fly out at different angles, so there is a high probability that such a drop or fragment will fall into the eye.

Given the speed of rotation of the fishing line, their blow can cause serious injury to the eye, and in the field to clear the surface of the eyeball from them is extremely difficult. Therefore, the main element of equipment is glasses or mask that protect the eyes from the opening of drops and crushed grass.

The remaining important elements of equipment are:

• protective headphones (relevant when working with motorcycles);
• a convenient suspension system (relevant for any trimmers with the upper location of the motor);
• Comfortable shoes with corrugated sole sole.

Preparation of a trimmer for grass

Any apparatus is suitable for working with flat mechanical coils. If you are going to mow grass with an automatic or semi.automatic head, then a higher protection is needed.

Devices originally designed to work with fishing line were equipped with a protective casing of increased heights, and part of the models, which included wheels or knives, were equipped with a casing with the so.called “beard”, that is, a removable lower part. This made it possible to change the height of the casing, adjusting it under the cutting tool.

But the devices, in the configuration of which there was no standard coil at all, was equipped with a low protective casing without a “beard”, therefore, either a “beard” or a casing of increased heights are needed to work with collapsible mechanical or any plastic coils.

In addition, when working with a knife, the protective casing often received damage, so for mowing grass the fishing line, it was required to replace it. The most effective was the choice of a universal casing with a “beard”, for example, such.

We also suggest you learn more about the principle of the electrimmer from this article.

Directly mowing

Theoretically, mowing herbs with a motorcycle or electric shock is similar to the use of a conventional braid braid, that is, turning the device to the left and right, gradually move forward.

At each passage, the fishing line for the trimmer will cut the vegetation strip with a width of 1-5 cm, and the mowed grass will either fall into the dangled area or fly apart.

However, in reality, a lot depends on:

Unlike a lawn mower, which collects beveled vegetation in a grass receiver, a trimmer for grass only cuts the grass and leaves it on the site.

If you choose the irregular trajectory of movement, then the mowed grass will fall under the cord again, which will have to grind it, reducing the speed of movement.

Principle of operation

If we consider the principle of the trimmer for the grass, then it looks like a manual braid. The difference is that it is equipped with an engine, with its help the cutting element is brought into rotation.

Producer companies produce the following models of mowers:

• On which a gasoline engine is installed. Such garden tools have a fuel tank, this is their distinguishing feature.
• Electric engine devices. These tools have less weight, because they do not have a fuel tank. But when choosing such models, you need to take into account that a power source needs their work to work.

All electric braids for grass can be divided into those that work on batteries, and models connected to an electric network. Each species has its own characteristics, but they affect the power supply unit. If you do not take into account it, then the rest of the design are similar in different devices.

If you take any model of a trimmer for grass, then it consists of such elements as:

• motor;
• fuel tank (electric motor does not have it);
• levers with which the mowing is controlled;
• knife for cutting grass;
• barbell;
• Spool with wound fishing line, which is cutting grass;
• protective casing;
• conical gearbox.

The engine is placed near the mowing head, it can be installed from below or from above. Only those models that have a direct bar with a gearbox. If it is curved, then the indigenous bearing becomes a connecting element. It consists of 2 bushings.

As a cutting device, a fishing line for a trimmer is used. It is easy to replace with steel knives and discs, they can be made of plastic or metal.

The choice of cutting element depends on how hard the grass will have to mow. Most often, the work uses a fishing line for a trimmer, it is called the cord. There are products of various shapes on sale, among buyers a spiral and round is in demand.

The fishing line for the trimmer is wound on the coil, it is inserted into the bobbin, while the 2 ends of the wire remain free. Когда двигатель косилки начинает работать, шпулька вращается, трава срезается свободными концами лески.

How to use a trimmer correctly

Garden trimmers for grass are effective. Newchers think that it is easy to work with a lawn mower, because you just need to include it in a socket or pour fuel, but this is not entirely like that.

The efficiency of the garden tool and its service life directly depend on operating conditions. Therefore, before using a trimmer for grass, you need to perform preparatory work.

The lawn with which you need to mow the grass is carefully examined. Be sure to remove glass and large stones. Having flew out from under a working mower, they can injure a person. They remove the wire from the lawn, because it can be wound on a rotating element, break a mower.

After that they move to the installation of the cutting system. There are trimmers for low.power grass on sale, which use only a fishing line for a trimmer. It is designed for mowing juicy and soft grass. But there are models with a capacity of more than 1 kilowatts on which metal knives are installed. They cut sowing and other hard weeds, trim the young shrub.

In order to replace the cord with knives, you need to unscrew the mounting nut, install the cutting element. Then the nut must be returned to the place, tighten it with the key.

The operator must take care of his safety. Mow grass in tight protective clothes. Special glasses are used to protect the eyes, they will protect from dust, grass and flying garbage. Hands are covered with gloves.

The electric trimmer for the grass is included in the network, and the battery models are charged for several hours before starting operation. Fuel is poured into a gasoline mower.

The mower is kept so that the spool or knife is located parallel to the ground. When the tool is installed in the correct position, the motor is included. After the grass is bewildered, the mower is turned off.

First start

Before the first launch, the operator collects a mower, the procedure is described in the instructions that are attached to the product.

If the trimmer for the grass is gasoline, it is necessarily checked before operation. The fuel tank is filled along the neck.

The motor should work for the fuel, so at the first launch it should work for several minutes without load. After that, start mowing grass.

How to refuel a benzotrimer

Motokos working on gasoline are with two.stroke and four.stroke engines. The first option is much more common. What are the differences between them:

• in trimmers with a 2-tact engine, the response to press the inclusion lever is faster (for this reason the lawn mower is mainly equipped with this type of engine);
• A tool with a two.stroke engine will be much easier, as well as easier to maintain;
• Fuel consumption in a two-stroke engine is higher than in a 4-stroke with a similar power by about 30%;
• The 4x-stroke engine is more environmentally friendly, since the fuel in it burns completely and is not thrown into the atmosphere, as well as its noise level is much lower;
• And the most important distinguishing feature is the refueling: a 2x-stroke engine is equipped with one common tank, where gasoline mixed with butter is poured; 4x-tacte has a separate gas tank and a tank for motor oil.

For refueling, it is necessary to use fresh gasoline AI-92 or AI-95 and high-quality motor oil for garden equipment (for 2x- and 4-tact engines, manufacturers produce different oil). Oil can be used mineral, semi.synthetic or synthetic.

The proportion of gasoline and oil for trimmers with a 2x-tact engine can be found from the instructions for a specific model. Usually it is 50: 1, in some cases, proportions of 25: 1 or 40: 1 are recommended. Prepare the fuel mixture in a separate container with accurate observance of proportions. Never pour the liquids “by eye” directly into the tank without mixing them in advance. Detailed instructions for mixing a benzomalam, with video and description, can be found on our website here.

Running

Before starting operation, gasoline braids are necessarily rolled up. The operator turns on the motor, he must work for a while at idle. It is necessary to ensure that the engine does not overheat, the load should not be.

When running in, motorcycles increase the load gradually. If you start work with high speeds, the motor will work well, this will affect the further work of the mowing.

At the first launch, you should not fully develop a temporary resource. After the engine works at idle, you can proceed to processing the lawn. The lawn mower should operate for no more than 15 minutes, after which the engine is turned off, it must cool down.

If you need to run the electrimmer, the braid is first collected. Then make trial launches at least 3-5 times. If the engine works well, go to mowing. At first they work for no more than 5 minutes, then the duration of work is gradually increasing.

How to wear a belt

If the tool has a shoulder mount, before starting work it hangs on the shoulder. The trimmer for the grass is fixed on both shoulders if it has a backbone mount.

The model with a bicycle handle is held with 2 hands, the D-shaped handle is wrapped in palm. The belt must be worn so that it is convenient, then the back will not get tired.

How to cut the lawn so that it turns out to be even

So that the grass on the lawn is trimmed evenly, it is necessary to lower the mower as low as possible during operation. The site must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left without interfering under the feet.

Kosim under hay

It is better to mow hay not with a fishing line, but a metal disk. Grass is cut under the root, maintaining its length as much as possible.

Spinning high grass

If you need to mow high grass, this is done in several suits. The lawn processes 2-3 times. The rotating part is lowered from top to bottom, in which case the grass is not wound on the reel.

The operator must remember that the grass wound to the coil leads to overheating of the motor. If this happened, the motorcycle is turned off, and the coil is cleaned.

Most effective mow grass with the ends of the fishing line, and not the entire length. In the second case, the tool works worse, engine overload is possible. If you need to cut the grass on the site of a large area, to increase the efficiency of a trimmer for the grass, you must be tilted towards the mowing.

The location of the main parts and controls

Assembly of the lawn mower

Remove the lawn mower and components out of the box. Check the lawn mower for the lack of mechanical damage.

Install the handle in the working position and fix it with special locks (a) (rice.3). Check the installation of control cables, they should not be overthrown. Install the grass collector. To work with the possibility of side emission of grass, install a groove for the release of grass (rice.four).

Install the handle in the working position and fix it with special nuts (rice.2). Check the installation of the engine shutdown cable, it should not be pushed.

Set the starter’s handle in the guide bracket on the working handle (rice.5).

Checking before starting work

Engine oil

Motor oil is the main factor that affects the operational characteristics of the engine and determines its resource.

ATTENTION! The lawn mower is supplied without oil in the engine. Before starting operation, it is necessary to pour the recommended oil into the engine crankcase.

ATTENTION! It is recommended to use Champion oil for 4-stroke engines, or high-quality motor oil similar in its properties that meets the requirements of the class SF, SH according to the classification of the API (oils classified as complies with the requirements of the class SF, SH, must have appropriate labeling on the package ). You can not use dirty engine oil, or motor oil for a two.stroke engine. Each time before starting the engine, you need to check the oil level in the crankcase, having previously set the lawn mower on a flat surface. When choosing oil, be guided by the table shown in the figure.

ATTENTION! Untimely oil change, working on the oil resource, working at a constantly reduced oil level, working in oil does not correspond to the ambient temperature, will lead to the failure of the generator engine and cannot be repaired under the warranty.

ATTENTION! The first oil change is made after 8 hours of engine operation. The second oil change after 25 hours of engine operation. All subsequent oil replacements are made every 50 hours of engine operation.

Refueling/checking the oil level in the engine

To fill the oil into the engine, install the lawn mower on a flat surface. Remove the lid with a probe from the flood neck (rice.6). Pour the required amount of oil. Install the probe in place.

ATTENTION! Checking the oil level in the crankcase is carried out on a non.working engine.

• Install the lawn mower on a flat horizontal surface. If the lawn mower worked before that, after stopping, let the engine stand for about 5 minutes.
• Clean the zone around the oil-lump neck.
• Remove the probe and wipe it with a clean rag. Install it in the neck and fix it (twist).
• Remove the probe again and check the oil level. He must reach the Full mark (filled).
• If necessary, share oil to the required level.
• Install the probe in place.

ATTENTION! Before starting the engine, check whether it is correct or not, a probe is installed.

Fuel

Use unhealthy gasoline with octane number 92. Never use old or contaminated gasoline or mixture oil-benzine. Avoid getting dirt or water in the fuel tank.

ATTENTION! The failure of the engine according to the approxim of using poor-quality or old fuel, as well as fuel with an inappropriate octane number, is not subject to warranty service.

ATTENTION! Store fuel in containers specially designed for this purpose. It is forbidden to use cans of food plastic for storage.

WARNING! The gas station is carried out when the engine is turned off and in places with good ventilation. When working with fuel, it is forbidden to smoke and apply open fire. Fuel spill is not allowed. It is necessary to prevent multiple or long.term touch of the skin with fuel, as well as inhalation of fuel vapors. It is forbidden to access children to fuel.

Do not fill the fuel tank completely. Pour gasoline into the fuel tank to a level of about 25 mm below the upper edge of the bay neck to leave the space for thermal expansion of fuel. After refueling the fuel tank, make sure that the cork of the flood neck is closed properly. The maximum fuel level is shown in rice.7.

Mixing rules

And now about how to mix components correctly. However, it will be more logical to begin with the analysis of the common, but absolutely unacceptable mistakes that many owners of this mowing unit “sin”. The following actions are considered errors of mixing the fuel mixture.

• Adding oil to a fuel.up teddle already filled with a gas tank. Similarly, a homogeneous fuel mixture cannot be obtained. Perhaps, and it will turn out, if only then shake a trimmer for the grass for a long time. But it is unlikely that someone will do this, given the severity of the unit.
• First pour oil in a container for mixing, and then add gasoline to it. Gasoline has a lower density than oil, so if it is poured to the clock, it will remain in the upper layer, that is, natural mixing will not occur. Of course, it will be possible to mix later, but there will be much more energy than if it were done the opposite. pour oil to poured gasoline.
• Ignoring accurate measuring means to take the necessary volumes of the ingredients used. In other words, breeding the amount of oil or gasoline “by eye” is a bad habit of operating motor vehicles.
• Take empty drinking water bottles for preparing the fuel mixture. Such containers are made of too subtle polyethylene, which can dissolve gasoline.

Given all of the above, we recommend that when mixing the fuel mixture for two.stroke trimmer engines for the grass, use the following rules.

• Use for storing gasoline, oil, finished fuel mixture and its preparation only pure metal containers or special plastic.
• Use to fill gasoline into the dilute container with a watering can in order to avoid its strait, and to add oil. a measuring container with volume risks or a 5 and 10 ml medical syringe with a medical syringe.
• First pour gasoline into the canister for the preparation of the fuel mixture, and then the oil.
• To dilute the mixture, first only half of the planned volume of gasoline is poured into the container.
• Next, add the entire amount of oil required to prepare the mixture to gasoline.
• The contents of the diluting capacity are thoroughly mixed. It is best to interfere, making circular movements with a tightly closed capacity. It should not be stirred by any extraneous object inside the canister, since it is not known from what material this item is made, into what reaction with the ingredients of the mixture it can enter, how pure it is.
• Add the remainder of gasoline to the mixed mixture and mix thoroughly again.
• You can refuel the fuel tank of the lawn mowing with the prepared mixture.

It must be borne in mind that the finished fuel mixture should not be stored for more than 14 days, since it loses its properties, relaxes and evaporates, which leads to changes in the proportions, and therefore the deterioration of the trimmer for the grass.

The consequences of a violation of the ratio

The working resource of the engine of motorcosa depends on how accurately you will observe the proportion of the oil-Benzos mixture. The fact is that the fuel mixture enters the cylinders in the form of gasoline-oil fog. And the task of the oil composition is the lubrication of moving and rubbing parts and surfaces of various details located in the cylinder. If suddenly it turns out that the oils are not enough, and somewhere it will not be enough, the details in contact with dry ones will begin to damage each other. As a result, scams, scratches and chips are formed, which will necessarily lead to complete or partial indifference of the engine (for example, it can jam it).

In the opposite case, when too many oils enter the engine, it does not have time to completely burn, settling on the walls of the cylinder and turning over time into solid particles. coke, slag and the like. As you can guess, this also leads to the failure of the engine. The most important thing is that you cannot allow. even a single violation of the proportion towards the lack of oil. It is better to pour a little oil 10 times than only 1 time do not add. It often happens that this time is quite enough to break the engine.

Features and advantages of motorcycle and trimmers Champion

Among the main advantages of electric and gasoline cos brand Champion, experts highlight the excellent build quality and a high degree of reliability of models. Champion lawn mowers are equipped with high.quality engines, all spare parts of which are made of durable metal alloys with high wear resistance and long.term working resource.

The great advantages of the Champion Garden Equipment is the ergonomics of motorcycle and trimmers, ease of maintenance and repair, modest fuel consumption and electricity. At the same time, each released model shows the highest performance under almost any working conditions.

With all the available advantages, trimmers for grass and motorcade Champion have a low cost, which allows you to choose the right model to absolutely every buyer.

Trimmer for grass gasoline Champion T394FS-2 spark plug as a gift!

Trimmer for grass gasoline Champion T394FS-2-is equipped with a powerful four-stroke engine with a light start system and an forged shaft, a T-shaped handle and a straight bar. Designed for mowing grass, weed, dry.

Stock

Varieties

Currently, the Champion brand is available two main varieties of trimmers:

Electric models with a battery, unfortunately, are not produced by the company. All products are equipped with a coil of a proprietary cutting fishing line and a belt with a hip system. Consider the range of trimmers “Champion” Read more.

trimmer for grass gasoline Champion T 256 Two cords of spark plug as a gift!

Trimmer for grass gasoline Champion T 256. this light and practical model will cope with different types of vegetation and will achieve an excellent result when cutting lawns. The engine on the basis of which the device is assembled on.

Stock

trimmer for grass gasoline Champion T 333 Two cords of the spark plug as a gift!

Trimmer for grass gasoline Champion T 333. such a technique is created to optimize the process of haircuts of grass and reduce the time spent on work. The power of the engine on the basis of which the device was created is 1.25.

Stock

trimmer for grass gasoline Champion T 333-2 Two cords of spark plug as a gift as a gift!

Trimmer for grass gasoline Champion T 333-2 is an indispensable tool for ennoble the site in hard-to-reach places, in which the usual lawn mower cannot get due to its design features.

Stock

How to prepare for winter storage?

To prepare a trimmer for grass for winter storage, do the following:

• Carefully clean the entire surface of the trimmer for grass from the remains of grass;
• Remove the cutting tool and grease all the metal parts with a thin layer of engine oil or treat with silicone spray;
• Disconnect the drive shaft from the engine;
• Remove both gearboxes;
• Lubricate all the slots of the gearboxes (including from the cutting tool) and a drive shaft rod with any engine or transmission oil, including the development of the engine of the benzotrimer, if you plan to store the device assembly, or any thick lubricant, if separately;
• Install the gearboxes on the drive shaft (if required);
• Connect the engine and drive shaft (if required);
• Install and adjust the handles (if you plan to store them on a trimmer);
• Pour all gasoline from the tank and tighten the lid of the fuel tank, then start the engine and wait for its stop;
• After cooling the engine, unscrew the candle from the engine;
• Pour 1-3 ml of pure motor oil into the combustion chamber, then screw the candle in place and smoothly pull the hand starter cable so that the engine will make several revolutions and evenly distribute the oil;
• Rinse and blow, or replace the air filter;
• Rinse the fuel filter (if it is installed on a trimmer).

How to use a gas toss correctly?

The only way to extend the service life of a trimmer for grass is its proper operation. Unfortunately, some of the manufacturers are not interested in the too long service life of their products, so part of the rules that help to more carefully spend the resource of the apparatus are not included in the instructions for the operation of the benzotrimmer.

For this reason, we recommend carefully comply with all the recommendations of this article, even if they are not in the operating manual, because we made recommendations on the basis of:

• the experience of operating many owners of devices that they were divided on the pages of various forums;
• tips of those who are engaged in the repair of motorcycle;
• Recommendations from the operating manuals of trimmers of the most expensive and high.quality brands.

Since the operation of a trimmer for grass implies not only mowing grass, but also many other actions, we divided it into the following topics:

• The engine is running.
• The choice of revolutions.
• The direction of the mowing.
• Choosing clothes and protective equipment.
• Security measures.
• Transportation and storage.

The engine is running

Despite the fact that the engine of the newly purchased trimmer for the grass is already driven and you can immediately proceed to the mowing of the grass, avoid maximum speed for the first 3-5 hours, because the final grinding of the parts of the cylinder piston group occurs.

If we allow the motor output at maximum speed, then there is a high probability of the appearance of stray on the walls of the cylinders, and this will lead to a sharp drop in the efficiency of the motor, and will also greatly reduce its resource.

The choice of revolutions

The maximum torque of the motor appears at revolutions corresponding to 2/3 of the maximum, and the greatest power appears at revolutions corresponding to 3/4 of the maximum. Therefore, the most effective trimmer for grass mows grass in this range.

The exit to maximum turns slightly reduces power, so during the mowing of grass, focus on the sound of a trimmer for grass and evaluate the speed according to this parameter.

If the load is too high and the rotation speed of the power unit shaft is reduced, add the gas using the corresponding key on the working handle.

As soon as the load decreases and the turns increase, press the gas key less to return the speed of rotation of the motor shaft to the optimal value.

If before you have never used a motorcycle, then until the completion of the run.up, mow only low and non.thick vegetation, which a trimmer head with a fishing line easily copes with. After completing the running.in, the engine will cease to be afraid of maximum revolutions, and you will acquire a sufficient skill to control the motor by ear.

In addition, avoid the long operation of the motor at idle, because because of this, the lubrication of the crankshaft bearing is deteriorated, which can lead to its overheating and jamming.

The direction of the mowing

When working with a motorcycle system in the maximum capture mode, move it so that it goes against the direction of rotation of the cutting tool.

In this case, the knife or disk will repel the device from a possible obstacle, so the trimmer for the grass will not jump out of hands.

In addition, with such a movement, a knife or head is thrown back in front of you, so you will better feel the resistance of the mowing of grass, which means avoid too fast movement and caused by it:

For most trimmers, the right direction of mowing grass is movement from right to left. When moving in the opposite direction, the trimmer for grass continues the mowing of grass, so the probability of a reverse blow increases, due to which the device can be very jerking. Therefore, when moving in the opposite direction, try to capture smaller grass to reduce the load on the device and the probability of a reverse blow.

The choice of maximum maximum capture mode is especially important at:

In addition, when pruning trees, try not to raise a cutting tool very much, but also not to turn it perpendicular, because this can lead to a violation of the carburetor.

This requirement is not relevant only for trimmers-crossbars, whose carburetors work equally effectively in any position.

Choosing clothes and protective equipment

A trimmer for grass is a device of increased danger, so to work with it you need to choose the right clothes and protective equipment.

When going to mow grass, put on only clothes without any straps and fringe, which can tighten a rotating cutting tool.

If you put on shoes with laces, then take measures so that they do not untie. If you have long hair, then limit their mobility by putting on a hat or tied with something. Be sure to put on glasses or a protective mask, because it is likely that the grass cuts will not where it should and falls into the eye.