How To Wind Line On The Huter Trimmer

How to wind line around the trimmer head or lawn mowers

Preparing for replacement

We disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, it is not necessary to remove it, everything is done locally. It does NOT take long.

We disassemble the trimmer spool. It rests on a latch-latches. Remove the cover by pressing on the latches. If you do it with your hands, there is not enough effort, then use a screwdriver.

The spool consists of the following:

• Spring case
• Cover with locking latch
• Reel with button

The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. By holding the reel in this state, you can twist it by adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.

Disassembled trimmer spool

On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (as here) they are signed, in others there is.

These holes are needed to fix the line when replacing it. After winding on the grandmother’s fishing line, the ends of the latter are inserted into them. This is necessary so that the scaffold does NOT unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.

Holes for fixing the line

There are models without specifying the diameter of consumables. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for the outlet of the fishing line from the trimmer spool body (see Figure below).

Fitting on the holes of the line output

The reel has two line sections separated by a baffle. They may not exist. They are needed only to distinguish and facilitate the winding of consumables.

Two sections for line

First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. THOSE. For two sections, you need a 4 meter segment. This is for the 1st way. For the second method, you need two segments of 2 meters each.

Determining the required line length

Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.

Special designation on the reel

If such designations were not found, then you need to Pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Bobbin case designation

Changing the line in the trimmer: 2 easy ways

In this manual, we will walk through the entire replacement process step by step. Going forward, there are two ways to line the trimmer spool. There are fundamental differences. The difference is that in the first case, one line will be refueled, folded in half, and in the second there will be two such lines.

:

Method 2. Two segments

Two coiled line pieces

Method # 2 is not fundamentally different from method # 1. The only difference. Two coiled line lengths instead of one.

The end of each segment is folded

The end of each segment is folded.

Two special fixing sockets

There are two special fixing sockets on the coil (see picture above).

We start reeling the line

They cling to it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order

The winding must be carried out in the following order: first the lower line, i.e. The one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. The one that will overlap the bottom section.

The bottom line is reeling

The tip is made into the holes in the trimmer spool body. They are pulled to clicks, which means that the line has come out of the clips.

The tip is threaded into the holes in the trimmer spool body

The coil is fastened into the body. The line in the spool has been replaced.

The line in the spool has been replaced

The first way

Line bent in half

The prepared segment (in this case, it is 4 meters) is bent approximately in half. One piece should be 15-20 cm longer, and is inserted into a special slot located on the dividing wall.

The line is inserted into the slot

In a certain direction earlier, the fishing line is wound. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs that do not provide for dividing the coil into two sections. This does NOT change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.

The first should end the segment that is located at the bottom of the coil, i.e. The one closest to the fixing holes.

This tip fits into the corresponding hole in diameter. The line is securely fixed.

The line is securely fixed

A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.

A long segment is wound another half turn

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body.

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body

The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing line, fixed earlier in the holes of the reel, pops out from there. It is easily identified by the characteristic sound (click).

The ends of the line pull up with effort

Button spool snaps into trimmer spool housing.

Button spool snaps into trimmer spool housing

The line was changed successfully. In this case, you need to set it back to the trimmer and you can start Mowing the grass.

It should be repeated, there is no need to remove the spool from the trimmer. This was done for clarity of the process of replacing the line. You can disassemble the spool in place, wind it on the spool and put it back.

Line replacement completed successfully

The tip so that they do not hit on the trimmer cover can and should be trimmed.

How to wind line around the trimmer head or lawn mowers

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

Changing the line in the trimmer: 2 easy ways

In this manual, we will walk through the entire replacement process step by step. Going forward, there are two ways to line the trimmer spool. There are fundamental differences. The difference is that in the first case, one line will be refueled, folded in half, and in the second there will be two such lines.

The first way

Line bent in half

The prepared segment (in this case, it is 4 meters) is bent approximately in half. One piece should be 15-20 cm longer, and is inserted into a special slot located on the dividing wall.

The line is inserted into the slot

In a certain direction earlier, the fishing line is wound. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs that do not provide for dividing the coil into two sections. This does NOT change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.

The first should end the segment that is located at the bottom of the coil, i.e. The one closest to the fixing holes.

This tip fits into the corresponding hole in diameter. The line is securely fixed.

The line is securely fixed

A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.

A long segment is wound another half turn

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body.

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body

The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing line, fixed earlier in the holes of the reel, pops out from there. It is easily identified by the characteristic sound (click).

The ends of the line pull up with effort

Button spool snaps into trimmer spool housing.

Button spool snaps into trimmer spool housing

The line was changed successfully. In this case, you need to set it back to the trimmer and you can start Mowing the grass.

It should be repeated, there is no need to remove the spool from the trimmer. This was done for clarity of the process of replacing the line. You can disassemble the spool in place, wind it on the spool and put it back.

Line replacement completed successfully

The tip so that they do not hit on the trimmer cover can and should be trimmed.

How to wind line around the trimmer head or lawn mowers

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

Feedback: Trimmer head Huter. One of the serious basics of Huter trimmers.

Semi-automatic head with line for trimmers Huter ETH-1200 comes with a reeled round line with a thickness of 2mm and a length of 5m. Head weight 320g. The head has a spool with a line and two metal holes through which the ends of this line are removed, carrying out mowing of grass with fast rotation of the head trimmer. Designed for electric trimmers Huter Get-1200SL.

When mowing grass, the line ends are worn out and their length is reduced. Consequently, the cutting radius becomes smaller. The length of the line ends can be restored by lightly hitting the ground with the button located in the center of the head, while the trimmer head is gaining momentum. After that, the two ends of the line will be fed, the excess of which will be cut off when you rotate the trimmer knife.

Sooner or later, either one of the cutting ends breaks off into the fishing line at the root and you need to refill it, or the line ends and you need to wind a new one.

In short, it becomes necessary to remove the head cover and pull out the bobbin for the line from the body. Here the fun begins. A similar situation is described in the fable by Ivan Andreevich Krylov “monkey and glasses” 🙂

The fact is that the Huter trimmer head has a unique design, which I have never seen before. Opening it to reload the line is not for the faint of heart.

There is no description of how to do this. The inscription on the back of the head body in English “click to open did not help. I pressed, tried to turn the body in both directions. Nothing helped.

As time passed, I, of course, forgot this unique experience. Going to bow again to Antonin was already inconvenient. I had to turn on the brain and deal with the problem in detail and in detail. The Internet suggested a way to uproot the trimmer head cover. Which did not suit at all.

From what I found, I understood the device of the head. It turned out that the cover is held on four holders that are attached to the sockets of the body and is fixed with a latch. By pressing it with a suitable flat-blade screwdriver and returning the body clockwise, you can easily remove the cover and pull out the bobbin with the rest of the line.

The line threading is standard and is described in detail in the trimmer description. It is also not easy, but you can figure it out.

When using the head for a long time, a little earth, grass residues and all kinds of dirt are stuffed into it. For the good of the case, I cleaned out the dirt from the body and the outer parts of the head.

Assembling the head is easy. It is necessary: ​​- to thread the ends of the line into the corresponding holes of the body:

In the photo, among other things, slots for attaching fishing line sizes from 1.6 to 2.6 mm are visible on the bobbin. For Huter Get-1200S electric trimmers, a 2mm line is recommended, which is securely attached to the 2.4mm line slot.

Next:. align the holders with the corresponding slots in the housing cover. by simply pressing the back of the body with the bobbin and line inserted. latch the cover latch latches. will return the case counterclockwise.

I got great satisfaction after I finally managed to remove the head cover 🙂 The feeling of victory over the recalcitrant and hostile Nature to you 🙂 Like the Taming of Klodt’s horses on the Anichkov bridge in St. Petersburg.

Whether or not to buy such a trimmer head? Only if you want to wrestle with it when changing line. In addition, the weight of this head is 15g higher than the weight of a similar head from Patriot trimmers. How important it is. I don’t know.

The plastic is ordinary, I haven’t crumbled yet, but people complain about its fragility. In case of careless strikes into the ground, it can crumble.

In fact, the thread in the head is standard left M10x1.25 LH. Accordingly, a head for a 2mm line can be used with a standard one with the same thread, for example, from a Patriot trimmer.

There are enough offers at different from different manufacturers on the market. Here are the most democratic ones in completely outrageous for automatic heads. You can choose the most suitable for you.

What types of woods are there

The most common type of line, which fits almost all types of reels. Round cord. This is an ordinary fishing line, suitable for cutting succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with shrubs.

As a rule, the diameter, which can mow young grass, and does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass just due to the existing sharp edges, but its disadvantage is greater wear and is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only for lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs in which the segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine power of more than 1.5 HP. Use cords with a metal cable inside.

This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the above listed opponents.

How to remove or tuck the line into the trimmer

In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, on which there is a special hook for easy winding of the fishing line.

Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to stretch the line of the required length. The photo below shows a few examples of different trimmer spools.

The bobbins of the trimmers, the motor of which is located in the ground itself, have a different attachment to the axis of rotation, they have two buttons on the coil on the sides, which must be wrung out, otherwise the whine replacement is NOT different from other cassettes.

The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two tendrils.

To remove the spool with the fishing line, it is necessary to Unscrew, located in the center, the screw, but Note that the thread is left there, so it will have to turn clockwise, this was done on purpose so that during operation It does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and remove the spool onto which the fishing line is directly wound.

Having measured the required length and folded in half, you need to tuck the fishing line into the spool.We bring out, in total, its ends opposite each other (for this there are special slots for fixing).

After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.

If in doubt or it is not entirely clear how to load the line on the trimmer, we recommend that you look at: how to properly wind the line into the lawn mower.

In thiss in detail, step by step, the instructor will open the trimmer head, measure the required amount of fishing line, as a rule, it is from two to four meters, and demonstrate assembly and installation on the trimmer.

How to put line on the huter trimmer spool

We just unscrew the lamb. When disassembling such a coil, you also need to make sure that the spring inside is not lost. Refueling with mowing line. In this, I show you how easy and simple it is to wind the line around the reel of your hand lawnmower yourself. If your coil is designed to work with just one tendril, that’s it. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. I wound the fishing line, we leave a small piece of it unwound to put it out. We fix this piece in a specially groove, located on the inner part of the reel and designed so that at the time of collecting the reel the line does NOT unwind. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, collect and put the coil back on the trimmer. If the coil is designed to work with two tendrils, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line.

There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. Reels with one groove should have a through hole through which the fishing line is threaded. We unwind 2-4 m of fishing line, threading it through this hole so that the fishing line sticks out equally on each side. Threads of this type are often used in gasoline-powered tools with an engine more powerful than one and a half horsepower. Metal-cored threads come in both round sections and sharp edges. Regardless of the type of section, such whining are the best suited for overcoming difficult-to-cut plants. Threads of this type can easily cut not only dry grass, but even small bushes. The wires with a wire inside compare favorably with other types of consumables for their incredible wear resistance.

Unfortunately, this feature has a more than noticeable impact on the price of this type. In addition, you should pay special attention to the thickness of the consumables. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the more dry and coarse weeds it is able to overcome. It is important not only to assess the capabilities of the material, but also to take into account the features of the trimmer. The use of improper whining may result in damage to the instrument. Using a thread that is too thick will overload the device motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism. That is why the choice of consumables must be approached no less responsibly than filling it into the trimmer. When a suitable fishing line is found and purchases, you can begin to consider ways of winding it on a reel.

At first glance, threading a line into the reel of a tool is not easy. But it is enough to study this process carefully. And in the future, all the necessary actions will be performed without any difficulty. Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of antennae of the line and the methods of its filling: Reel of lawn mowers with one tendril. Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters.

Double fluted head. In principle, there is no difference between bobbins with one and two grooves, but if carelessly threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones. Regardless of the number of strands for threading, a fishing line with a length of 1 is taken. Winding must be done in the opposite direction of the head rotation, since winding in the direction of travel will lead to the fact that the fishing line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends of 15-30 cm are threaded into special holes. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the peculiarities of the cultivated area. The larger the diameter, the easier it is to cut tough grass. Training. Removing and disassembling the spool In most models of electric and petrol trimmers, you will need to remove the spool to replace the fishing line.

To make the instruction universal, we will still consider it in detail: 1. Fix the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod. Take out the winding spool. The preparatory stage has been passed. You can proceed to winding the fishing line. How to wind the line on the spool of the trimmer First determine the length of the consumable for your spool.

Instructions with step-by-step descriptions of how to wind the trimmer reel and lawn mowers

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually provided for a tip, which will NOT allow you to make mistakes with the use of the appropriate equipment.

If the information on the spool is about the diameter of the fishing line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all are applicable. We will consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.

What you need to know about trimmer line

A fishing line is called a consumable, which consists of nylon, and serves as a cutting device. By means of this equipment, grass slopes occur, which is ensured by rotating the tool head at a high frequency. This material has different thicknesses, which depends on its use on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3 , 2 mm).

The more powerful the tool, the correspondingly thicker the cutting tool should be. This not only affects the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and recharge the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the Step-by-step instructions for replacing the line in the trimmer reel.

Method 1. How to wind the line correctly or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out the amount of line you need to refuel to charge the reel. To do this, wind the equipment inside the coil until it is equal to the side protrudes. In this case, the rigging should not go beyond these extreme protrusions.

The thicker the rig used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly tuck the equipment into the trimmer or lawn mowers is as follows:

• To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
• After that, take the second end from the other side, and fold it in half. Move to it so that the measured protrusion of 15 cm is preserved
• In the inner baffle of the coil there is a slot into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
• Next, find out the direction of winding the line. If you wind the rig in the wrong direction, it will NOT function correctly and the work will need to be redone. To insert the line and wind it in the correct direction, inspect the surface of the spool. The direction of winding should be indicated on it (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
• This pointer in the form of an arrow can also have a designation, as in the example above WIND LINE, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the fishing line, wind it on the drum in the opposite direction of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the direction indicated, and if it is there, then you should wind against the direction of the arrow on the surface of the head
• Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is a separator, then the equipment must be laid in the appropriate distribution order.
• When almost all the line is wound on a reel, you will need to do the following. Place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then similarly perform the procedure with the other end, placing it in the hole on the parallel side
• We insert the coil into the head, first pass the ends of the fishing line into the holes of the drum
• We put the drum in place and, pulling the ends of the line, disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover to trigger the latch
• At this point, the process of how to replace the fishing line with a trimmer is completed, and if necessary, you can only trim the ends (if their length is NOT suitable), and install the drum assembled on the tool

With how to put the drum in place, no difficulties arise. There is a second way, how to charge the mowing equipment in the lawn mower. What is the difference, and how is the second method of threading the line on the reel of lawn mowers carried out, Let’s find out in detail.

Learning to properly wind the line on the trimmer reel and lawn mowers installation instructions

Private home owners know how essential a trimmer tool is. It can be gasoline and electric, but they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during use, so how to wind the trimmer coil, we will consider in detail in the material.

Method 2. How to properly put the line on the reel of lawn mowers with a photo description and

The second method differs from the first in that the reel is loaded NOT with a single piece of equipment, but with two-piece pieces. Manufacturers use this method, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into the mowers’ guidance is the same as in the first method, and to make sure of this, below are detailed instructions:

• There are two equal length pieces of material that you can use
• One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If not, then the second option will NOT work. The appearance of THESE brackets is shown in the photo below. Each bracket is in its own half
• The fishing line should be hooked onto the bracket, and wind it in observing the direction of the arrow
• The rig is reeled up until a segment of 10-15 cm remains, which is fixed in the corresponding holes on the side of the aiming
• Manipulations with the second end of the fishing line are carried out in the same way.
• The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in the lawnmower will help you not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. The instruction is presented below.

How to remove the spool from the trimmer and remove the line

Initially, before threading the trimmer spool, you need to remove it from there. Coil or lead. This is a device that is located inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturers), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

The instruction on how to unscrew the manual head onto the trimmer is as follows:

• Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned. After lightly pressing them inward, remove the protective cover from the drum
• Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand
• The main part of the drum is fixed with a screw, which is necessary Unscrew with a screwdriver with an appropriate tip or bit
• To unscrew, hold the drum base with one hand, and unscrew it with a screwdriver counterclockwise with the other
• After that, you can proceed to dismantling. To do this, you do not need to pull it with all force, but slightly shake it to the sides, slowly disengage it from the metal shaft on which the drum is set
• When reinstalling, fit the head into the square slots

This process is NOT difficult, and as you understand, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, take into account the following nuances:

• It is recommended to remove the head periodically to prevent corrosion of the threaded connection. If you NEVER unscrew the screw, it will be difficult and sometimes even impossible to do this if necessary.
• If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude licking of the edges on the head
• When assembling the unit, treat the threaded seat with lubricants, such as grease or machine oil.
• If the edges on the screw are licked, then you can use special clamping pliers to unscrew it.
• There are drums that do NOT require any prior disassembly. To dismantle them, grasp it and rotate in the opposite direction to the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. Below is a detailed process on how to open the trimmer coil and disassemble it.