Install a fishing line for a trimmer on a trimmer for grass without taking off the coil. What can be used instead of fishing line

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

How to replace a fishing line for a trimmer on a trimmer how to wind a fishing line for a trimmer for a trimmer for grass

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Read how to clean the air filter on the echo trimmer

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Read how to put a fishing line for a trimmer on a trimmer for grass correctly

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut. A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

  • See the information about the thickness of the fishing line in the instructions attached to the trimmer.
  • Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters.
  • Another option is to try to insert the cord into the output. If it easily passes into it, then the selected fishing diameter is suitable for use.

Trimmer coil for grass

You can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

2.50mm VS 3.00mm TRIMMER LINE/ FISHING LINE CUTTING THE GRASS/GRASS CUTTING,

Pay attention to the type of cross section of the cordry thread. Some popular options:

  • The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
  • Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
  • The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
  • You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
  • The most durable is a two.component cord with an internal core and a round section.

Types of fishing line for grass for grass

Keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

Removing and disassembling the coil

The braid trimmer head consists of a casing, a spring (not in every model), bobbins with a cord, cover. Before proceeding to disassemble the coil of the electric unit, be sure to turn off the trimmer for the grass from the network. The disassembly method depends on the mounting of the mowing head. First option:

  • To remove the lid covering the inside of the head, click on the latches (latches), which are located on its two sides.
  • Remove the lid under which you will see the spool. remove it from the body. Some trimmers have a spring under the bobbin coils, which should also be carefully pulled out.
  • Removing the bobbin, you will see the screw in the center of the case. Unscrew it with a screwdriver.
  • After extracting the fasteners, take the case body and, shaking it in different directions, remove the gearbox from the shaft.

In the second version, the head of the trimmer for the grass is twisted onto the shaft of the gearbox. To remove it, you need to fix the shaft. To do this, in such devices there is a hole through which a thin screwdriver or metal rod is inserted. Brief Instruction:

  • Insert a screwdriver into a special hole, then stall the shaft.
  • Get the body of the head and start twist it. This should be done clockwise, t. to. Larva shaft thread.

Winding of fishing line on a reel

How to remove the coil of a trimmer for grass; The mowing head of a trimmer for grass

Before you start replacing the fishing line, you should separate the mowing head of the motorcycles in which the coil for the fishing line is located. This element is attached at the end of the stick of your trimmer for grass and removed by unscrewing it in the direction where the arrow on the coil indicates.

After removing the spiked head with a coil, it is necessary to open it. First of all, it is necessary to find on the coil a snapping mechanism. It is part of the coil and is like 2 clamps, by pressing which you can open the coil and get to the place where you need to wind the fishing line for the trimmer.

install, fishing, line, trimmer, grass

Open the braid and take out a coil for winding the fishing line

You can open the coil with both hands and using a screwdriver or other tools with which you can clarify the latching elements.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

  • Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
  • You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
  • Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
  • Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
  • After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
  • By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
  • Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
  • By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

You can wound a cord for a trimmer for grass in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

Learning to correctly wrap the fishing line for a trimmer to the coil of a trimmer for grass and lawn mowing instructions for installation

Owners of private houses know how necessary the type of tool is such as a trimmer for grass. It can be gasoline and electric, and they differ in the design of power units.

For injection of grass in areas where there are stones, trees and other obstructing objects, a fishing line for a trimmer is used as a cutting device.

This consumable in the process of use wears out, so how to wind the coil of a trimmer for grass, we will consider in detail in the material.

What you need to know about the fishing line on the trimmer for the grass

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device.

Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency.

This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers for grass with motorcycles (from 2.4 up to 3.2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material.

If you ask the question of how to wind the coil of a trimmer for grass, then it’s time to change the reload of the tool.

With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.by.step instructions for replacing the fishing line in the coil of the trimmer for grass.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum.

The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same.

First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting! The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

  • Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum
  • Next, from the rampart of the drum, the coil for the fishing line should be removed. It is planted on a shaft without fasteners, so it is dismantled with one hand
  • The main part of the drum is fixed using a screw, which must be twisted with a screwdriver with an appropriate tip or a bat
  • To twist it, it is necessary to hold the base of the drum with one hand, and the second to remove the screwdriver against the direction of the clockwise
  • After that, you can proceed to dismantle. To do this, you do not need to pull it with all your strength, but slightly shaking it, slowly remove it from the hook with a metal shaft on which the drum is planted
  • When installing the installation, the head should be planted in a tetrahedral slot

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

  • It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
  • If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
  • When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
  • If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
  • There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.automatic and automatic).

The instruction is presented above how to disassemble the head of the trimmer for grass without a spring, t.e. on a manual.type head.

The principle of dismantling a semi.automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.automatic coil of the trimmer for the grass is as follows:

  • Inside the head is a coil, which is planted on slots that prevent its free movement
  • The coil is affected by a spring that presses it to the slots located in the design of the cover
  • A fishing line for a trimmer is wound for a tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
  • During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the fishing line for the trimmer is wound from the drum, increasing in the length
  • Having released the required amount of fishing line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a fishing line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the fishing line for a trimmer simply breaks off, without having a negative effect on the gearbox and the engine engine, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the fishing line into the coil of the trimmer for the grass. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

In which direction to wind a fishing line for a trimmer on a trimmer

How to correctly wind a fishing line for a trimmer to a trimmer coil for grass

Many, having developed a factory fishing line for a trimmer on a not so long ago received by a trimmer, try to wrap the latest, but they can’t, because they don’t know how to correct the fishing line for a trimmer to the heel (bobbin) of a trimmer for grass. As if there is an abstract, but still does not come out. Let’s try to deal with this issue in this article.

So, in order to wind a fishing line for a trimmer, it is necessary, for a start, to remove the coil from a trimmer for grass. this will be more convenient. The removal method will depend on the type of trimmer for grass.

How to wind a fishing line for a trimmer to a mowing head of a trimmer for grass or motorcycle

The video carefully shows how to wind a fishing line for a trimmer to a trimmer coil for grass or motorcycles. The gas line is dressed

How to wind a fishing line for a trimmer to a trimmer coil for grass?

The answer to the question after the previous video.

than 200 types of trimmers in one place at the lowest prices. Press and look

Now, having removed and dismantled the coil, we proceed, in fact, to the winding.

Winding process

If your coil is created for work with only one antennae, then everything is very simple here.

It is necessary to rewind 2-4 m of fishing line (depending on the size of the coil), find the hole for the trimmer on the inside of the coil for the coil, stick one end of the fishing line there and start wiring the fishing line for the trimmer in the direction of rotation of the coil on the trimmer.

The inside of the coil is usually indicated with an arrow in which the side is to wind a fishing line for a trimmer. Having wiped a fishing line for a trimmer, we leave a small piece of it unnecessary to put it out.

We fix this piece in a special groove located on the inner part of the coil and created so that at the time of collecting the coil of the fishing line for a trimmer does not unwind. If there is no groove, then you will have to hold a fishing line for a trimmer with a finger, so as not to let it unwind during the upcoming collection of the coil. Further, we take the outer part of the coil and spread the outer piece of fishing line into the available hole, collect and put the coil back on the trimmer for the grass.

In the presence of 2 grooves, a piece of fishing line 2-4 m long is folded in half, we insert the loop in the groove at the groove at the place of 2 grooves, and wrap both ends of the fishing line at our own groove at once. Subsequent acts are similar to the previous option.

That’s all on this issue. How to replace a fishing line for a trimmer in a trimmer how to wind a fishing line for a trimmer for a thrima mowing head. Successful winding!

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting! The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

How the head with a fishing line on a motorcycle works why you need to know the principle of work

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.automatic and automatic). The instruction is presented above how to disassemble the head of the trimmer for grass without a spring, t.e. on a manual.type head. The principle of dismantling a semi.automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.automatic coil of the trimmer for the grass is as follows:

  • Inside the head is a coil, which is planted on slots that prevent its free movement
  • The coil is affected by a spring that presses it to the slots located in the design of the cover
  • A fishing line for a trimmer is wound for a tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
  • During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the fishing line for the trimmer is wound from the drum, increasing in the length
  • Having released the required amount of fishing line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a fishing line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the fishing line for a trimmer simply breaks off, without having a negative effect on the gearbox and the engine engine, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the fishing line into the coil of the trimmer for the grass. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

Preparation. remove and disassemble the rogue

In most models of electroly and benzotrimmers, to replace the fishing line, you will need to remove the coil. FUBAG tool (electrimmers and benzoprimers) allows you to skip this stage. For the instruction to be universal, we will still consider it in detail:

one. Fix the shaft. Insert a stop element into the corresponding hole. They may be a thin screwdriver or a metal rod.

Unscrew the spool body. In our example. strictly in the direction clockwise.

Unscrew the lid in accordance with the direction indicated on the case.

The preparatory stage has been passed. You can go to the winding of the fishing line.

How to wind a fishing line for a trimmer to a trimmer coil for grass

First determine the length of the consumable for your reel. Wrap a fishing line for a trimmer on a bobbin until it staches for the sides. We got 4 meters. How much will it work with you depends on what diameter of the fishing line for a trimmer for a spool and design features.

Winding algorithm

Lay the fishing line for the trimmer in accordance with the indicated direction on the element case.

Insert the short end into the groove on the side of the coil.

Fasten the long end in the opposite groove.

Place the coil with a wound fishing line in the spray building.

Cut the ends of the fishing line, leaving 10 to 15 centimeters.

The replacement of the fishing line is completed and now it remains only to fasten the bobbin on the trimmer for the grass and you can work.

How to remove and disassemble a coil

Before proceeding to the process of replacing the cord, users of trimmers need to remove and disassemble the coil. Consider how to do it.

The mowing head of a trimmer for grass consists of several parts: a casing, springs (not in all models), bobbins with a cord and cover.

Attention! Before proceeding with any actions to maintain an electric unit, it must be disconnected from the network.

Trimmers most often use 2 options for fastening a mowing head.

install, fishing, line, trimmer, grass

Option

To remove the head of the trimmer for the grass, it will require its complete disassembly.

    To remove the lid covering the inside of the head, it is necessary to press on the latch (latches) located on its two sides.

Option

In this version, the head is twisted onto the gear shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, take 2 simple steps.

  • Insert the screwdriver into the hole and stall the shaft.
  • Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

Fishing line for a trimmer. varieties and the ability to replace other material

A cord for a trimmer for grass can be of various diameters (from 1.2 to 4 mm), and it is necessary to choose it depending on which vegetation is required to mow. the thicker the fishing line is for a trimmer, the more rough grass it will manage. Experienced users advise to put a fishing line for a trimmer 2 mm wide, which is a universal.

The shape of the fishing line can be round (for juicy grass) or with sharpened faces in the form of a square or asterisk (for beveling dry grass). The 2nd type is the least durable and the rags wear out in a comparison with a round cord.

One of the favorites regarding the work of the trimmers is whether it is possible to change a special cord for mowers for other materials, for example, iron or iron cables and strings, wire, etc.D. It is necessary to know that the installation of such items is not recommended, since, coupled with them, a trimmer for grass is converted into terrible equipment. In the process of mowing, pieces of wire or metal will break through and fly away in different directions every time, risking the employee to injure. And if you touch the limbs during the work during work, the harsh wound is ensured.

The owners of the trimmers interested in whether it is possible to use the fishing fishing line for the trimmer, we answer. this is allowed, but it will even be more frustrated and wear out, but means to achieve often the substitution.

Replacing the fishing line with a disk or knife

When ennobleing a personal plot, park zones and other places where various plants are required, it is often necessary to change the cutting tool in the trimmer. This is dictated by the fact that the standard cord installed in a mowing head can only cope with herbs. But when a shrub or young growth of trees appears on the path of an employee, a fishing line for a trimmer cannot cope with such a task, and it requires a change to a more effective cutting tool.

NEVER BUY WEEDEATER STRING AGAIN!!!. WHO_TEE_WHO

Manufacturers of trimmers provided such situations, and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace a fishing line for a trimmer with a knife with several “petals”, then such a tool can be mowed by both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer to the disk, the user of motorcycles has the opportunity to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

    The first thing you need to remove, stagnating the shaft, a mowing head (twist clockwise) or a nut with anthers if the unit has not yet been used.

For a better understanding of the process of changing the tool, you can watch this video.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

  • Stones, small branches and other hard obstacles come across the grass;
  • The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
  • poor quality of the cord (it is recommended to purchase high.quality);
  • The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

a fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

  • The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
  • The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
  • Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
  • The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.