Lubrication of a trimmer for grass for grass gasoline Patriot. How to replace a gearbox with a trimmer ethletric for Champion grass

Patriot trimmers are a vivid demonstration of American production of garden tools

A huge role in the performance and durability of a gasoline trimmer for grass is played by oil, which protects the details of the cylinder.piston group from rapid wear.

In order for the lawn mower to delight its owner with trouble.free work, a competent approach to maintenance is needed. Currently, it is customary to distinguish between two main types of engine by the number of working tactes:

The principle of operation of two- and four-stroke engines

• two.stroke engines where oil is added directly to the fuel tank;
• four.stroke engines with a separate oil tank. An exception in this category is the STIHL 4-MIX motor, which works on an oil bosinzin mixture, but at the same time has 4 work tactes.

Nevertheless, most of the trimmers presented in our market are equipped with power units operating on a mixture previously prepared in a fuel tank.

For trimming grass in the country or in the field you will need gas trimmers for grass. They work on gasoline, unlike electrical counterparts. Not many masters know how to dilute gasoline and oil for trimmers, gasoline and motorcycle.

The best. The best gas trimmers for grass

The step.by.step guide for the preparation of a fuel mixture of a trimmer for grass will be useful not only to beginners, but also to those who may make mistakes with chainsaws. Trammers for grass and bushes are powered by two.stroke engines that have a simplified design. Rarely there are models of trimmers with 4-stroke engines operating on pure gasoline. Two.stroke power units do not have a compartment for refueling motor oil oil oil, which reduces the weight of the tool and reduces its cost.

If the rotating parts of the engine are not lubricated, they will ultimately fail. To prevent this, a trimmer for the grass is seasoned not with clean gasoline, but a mixture of oil.

What kind of oil to dilute with a gasoline trimmer? To begin with, we note or find out what types of oils are produced in chemical composition: from the foregoing it follows that oil of any composition is suitable for the trimmer for grass. Mineral water, synthetics and semi.synthetics. Oils with various chemical composition are different in price, so when buying you should rely on the recommendations of the tool manufacturer.

The manual contains the recommended information about which types of oils are best used. If this is the TC-W3 standard, it does not matter what the substance should be. In this case, mineral water, semi.synthetics and synthetics can be diluted with gasoline.

How to dilute gasoline oil for a chainsaw

It is interesting! When choosing oil, the main thing is not to go to the fake, because in our time very often you can find different types of lubricants for two.stroke engines, which mainly consist of poor.quality oil products.

If the operating guide for this tool is lost and there are problems with the choice of suitable oil, it is recommended to choose the following two options:. When choosing and buying gasoline oil, you can find that some inscriptions are indicated on banks.

Fuel quality

These designations are the API classification, which will be useful for finding out who wants to fill the lubricant with appropriate parameters in the tool. Consider all types of oils according to the API classification for two.stroke engines:. API classification. American standard used in Europe.

This is a classification of smoke gases developed according to the Japanese standard JASO. If such designations are found on the selected oils and chainsaws of the trimmer for grass, then they should be considered decryption:. Oil for two.stroke engines have 2T marking.

Knowing the classification of oils by their types, it will not be difficult to choose the best version of the brush for your brand. On the market you can find various brands of oils for two.stroke engines, but it is better to pay special attention to the following companies:.

Product are not indicated, since their are changing. There are many other brands, and if you still want to find the perfect lubricant for your trimmer for grass for yourself, we recommend that you watch the test in the video below. From the video we can conclude that the purchase of expensive oils is not always beneficial, since they can be of low quality, as shown in an example from real life.

Oil output! For artisans, trimmers or black cutters, it is best to choose a synthetic or semi.synthetic oil of the TA or TB class.

Preparation for the first section of the brush

At the same time, follow the manufacturer’s recommendations, as some manufacturers of high.quality equipment can recommend only synthetic oils. How many people, so many thoughts, not only about choosing oil for a trimmer for grass, but also gasoline.

Also, in order not to make a mistake in choosing, it is recommended to use gasoline of the brand, which is recommended by the manufacturer specified in the instructions for the tool. However, here not everything is so simple, because at each gas station gasoline is called only the same, but they have a completely different composition.

Choosing a brand of gasoline for trimmers

You need to select a brand of gasoline for motorcycles taking into account the recommendations of the manufacturer. If you do not follow them, then the motor will soon break. Often for refueling a gas tank of a trimmer for grass, unhealthy fuel with an octane number of 92 or 95 is used.

Trammering a trimmer for grass with gasoline AI-80 can lead to breakdowns of the device due to its low technical characteristics. Keep in mind that after the purchase you can store fuel no more than 60 days, and it is better to reduce this period.

Polyethylene canists are not used for storage, t. to. In contact with the internal walls, static electricity will occur. The accidental appearance of a spark will lead to an explosion. Although, there are special canists of plastic with the marking “Flame”.

Advantages and disadvantages

The Patriot Pt 555 model has established itself on the market from the best side. Consumers characterize this model mainly only on the positive side, highlighting it among other similar products. The main advantages include the presence of a double cutting system (a fishing line for a trimmer and a knife), which provides mowing not only of thick grass, but also of dry, small shrub. The Patriot Pt 555 is also distinguished by mobility-it is allowed to be used everywhere due to the lack of a wire. In particular, the reliability of the work of motorcycles in the conditions of bad weather is noted; high performance and excellent traction effort; semi.automatic fishing line; the presence of an adjustable handle, which can easily be configured in a convenient working position; a shoulder belt that provides prolonged work without fatigue; low fatigue in the development of large sparks; minimum maintenance and efficiency of maintenance; affordable price. We also note a low level of vibration. In general, users of the Patriot PT 555 motorcycles are highly appreciated by all technical and operational capabilities.

Many do not comply with some important recommendations for pouring fuel in the gas tank of the trimmer for grass or lawn mowing, which ultimately leads to unpleasant consequences. Consider important recommendations on how to properly fill in the gas tank of motorcycles diluted fuel from gasoline and oil:

Prepare a funnel or watering can. Despite the large diameter of the hole of the gas tank, very often when trying to get into it, a certain part of the fuel is spilled, which enters the tool case

The fuel that came to the tool can cause ignition when heated, so it is very important to use a funnel or a watering can before twisting the cork, you should carefully clean the surface of the tank, since pollution can get inside, which will cause a quick clogging of the fuel tanker should be carried out in the calm The weather or in a secluded place to exclude the likelihood of dust and small grains of sand inside the tank do not leave the open hatch of the tank for a long time, since not only small grains of sand and dust can fall into it, but also insects do not inhale gasoline vapors during filling, Since they are dangerous for humans. When working with a trimmer, the master should use protective glasses, headphones and a respirator to pour fuel into the tank, you need to mark before the mark

If you pour a full tank, then with screwing the cork, some will result in a non.excessive use of fuel. In this case, it is better to shorten than to pour

Given these recommendations, you can significantly extend the service life of the gasoline tool in question.

It is interesting!Work on the preparation of the mixture and pouring fuel is also recommended in protective gloves.

How to prepare a high.quality fuel mixture

• Gasoline is poured into the container to the corresponding mark.
• Oils for gasoline, and not vice versa, flows oil for a two.stroke engine to the level
• The mixture shakes it several times until uniform.
• If a special container is not provided in the configuration, use the usual gasoline canister. Make a mixture in this ratio of gasoline/oil 32: 1.
• To prepare a mixture directly in the fuel tank of a trimmer for grass is not recommended.

Buying any equipment in its kind is a lottery, but much also depends on the gardener. In caring hands and Chinese samples serve for a long time and do not let their owners at the wrong time. And if you forget to lubricate the motorcosa gearbox in time, do not clean filters, use cheap low.quality gasoline, then garden equipment from the most eminent brands will be a headache.

Lubrication of the gearbox Motokos is one of the most important elements of maintenance of a gasoline trimmer for grass, which the user should be carried out directly.

Time and procedure for the prevention of the gearbox

I recommend that the prevention of a new gasoline trimmer for grass immediately after purchase, with the addition of lubrication in the gearbox. For all the high cost of garden technology, some manufacturers save and lay lubrication only at a minimum, for the duration of the run.in.

How often to lubricate the gearbox motokos

Often, a preventive inspection of the transmission with the addition of liquid consistent lubrication is carried out once a year at the beginning or end of the season. If the gasoline trimmer for grass is used not in professional volumes, this is enough.

With large volumes of the mowing, lubricate the motorcosa gearbox every 20-50 hours of work. If the conditions of the operating mode of garden equipment are difficult, for example, a large field is pumped out at a time, and at the same time the lawn mower does not have time to cool down, or cheap lubricants are used, then the lubricant must be checked and added every 20 hours of work.

Indirect evidence that it is necessary to lubricate the gearbox to overheating or increased noise of the node.

I also recommend a complete replacement of lubrication, with disassembly and flushing of the node, when buying a used gasoline trimmer for grass.

Lubrication for gearbox of gasoline trimmer for grass

Assortment of lubricants for garden technology

According to the instructions for lubricating the conical gearbox, a special transmission liquid consistent grease should be used. As a rule, manufacturers of garden equipment produce and recommend the chemistry of their brand as the most adapted to their devices.

At the same time, to reduce the cost of the operation of garden equipment and increase the attractiveness of a brand of auto chemistry, grease for garden equipment usually produces multifunctional. It is intended not only for lubricating gearboxes of gasoline trimmers, but also for processing hoses, transmissions and gearboxes of any garden equipment and mechanical devices operating under high loads.

Such lubricant for the gearbox is sold in the tubes convenient for use and subsequent storage.

Even if a specialized lubricant for the gearbox was almost completely developed during operation, the additives still create an effective lubricating protective film on the surface of the gears.

It should be noted that many owners of the motorcycle in the vast CIS for lubrication of the gearbox use ordinary litol-24 or lubricant for Circus on a lithium basis. It is convenient to refuel the gearbox using a 5-cc medical syringe.

A undoubted plus of the use of lithola and lithium.based lubricant for refueling the transmission of motorcycles is a reducing reduction in operation. But there are nuances because of which spears are breaking on the forums of the Internet gardeners. My thoughts on the topic, what can be lubricated with lubric.based lubricants, and what is not read in the article “Litol as lubrication of the motorcosa gearbox”.

How to lubricate the motorcosa gearbox, gasoline trimmer for grass

Side Bolt on 17 on the gearbox of a gasoline trimmer for grass

In order to avoid random launch, all preventive work on a motorcycle is necessarily carried out with a removed electric cap / plug from a candle. Do not turn the trimmer for the grass to avoid gas leakage.

We unscrew the side screw on the motorcosa gearbox. Depending on the company.manufacturer of a garden tool, instead of a screw for a hexagon, there may be a turnkey bolt, more often at 17. The thread is ordinary, unscrew counterclockwise. Do not lose the sealing puck.

If the lubricant is not visible on the internal end part of the screw, then it is necessary to add 3. 4 grams. Scroll through the gear with your hand, changing the direction of rotation so that the lubricant is distributed through the gears.

Then set the screw in place, tightly tightening it.

We proceed to running the lawn mower

After starting, do not rush to immediately run the trimmer for the grass. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a fishing line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 30.40 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

Having cooled the lawn mower, we continue to run the engine according to the previous scheme. Start a hot, a trimmer for grass should already be with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the run.in a gas reducer gearbox for grass. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

In general, therapist for the lawn mowing according to the described algorithm is carried out until the fuel mixture in the tank is fully generated. After which the tool is ready for long.term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

Reducer device trimmer for grass

Regardless of the manufacturer and model, the modern trimmer for grass is equipped with a gearbox for changing the angle of mechanical energy between the drive shaft and the head with a fishing line. The most widespread in the benzocos were conical gears, since, unlike straight.tooth, gears with screw teeth are able to carry huge speeds, have a more smooth clutch and have increased bearing capacity.

In the duralumin case (1) there is a shaft-shuster (2) and a gear conical wheel (3), pressed on a driven shaft (4). To reduce friction forces during rotation, rolling bearings (5) are installed at the support points of the shafts. Any gear gear is a highly loaded mechanism, whose duration and reliability of which depends primarily on the lubricant. Therefore, except for the main above the components of the reducer device Trimmer for grass includes a special hole through which you can lubricate the bearings and gears without disassembling the node.

How to lubricate the gearbox of a trimmer for grass?

At the top of the case where the gear block is located, there is a technological hole, which is covered with a screw during the trimmer for the grass. This screw is unscrewed, and 1.5-2 million lubricants are introduced from the nose of the tube into the hole. If the purchased composition has a different packaging, then a regular syringe will fit into the hole to enter the mixture. After the screw is placed in its rightful place.

This operation, regardless of the user’s recommendations, should be repeated after every 10-15 hours of work of the trimmer for grass. In other cases, the gear lubrication is replaced and updated when the device is preserved in front of the winter, repair the assembly, washing and cleaning the gears at the beginning of summer, etc.P.

Being in a disassembled state, before applying a new lubricant, it is worth initially to completely remove the remaining the old mixture, even if they are not polluted and not oxidized.

After applying a new lubricant, you should handle the shaft a couple of times to make sure that the composition was equally distributed on all surfaces of the gearbox.

In the process of lubrication, it is important to pay special attention to the following components of the trimmer for the grass:

• Bearings with a worn seal through which the remnants of the lubricant during the operation of the unit could go out. With a lack of lubrication in this case, the device begins to vibrate markedly. This often happens with Chinese models, when choosing which it is worthwhile to think in advance about the replacement of the bearing knot with the highest quality analogue, for example, the Swedish SKF.
• Dog with a starter coil, as it often touches the grooves on the flywheel when the drive is turned on. In addition to mechanical wear, in this case there is also a mechanochemical corrosion between the compounds of the dog and the flywheel, since these components are made of different materials. a dog made of steel, flywheel. from aluminum.
• A flywheel, on the surface of which the remains of grass usually accumulate, and as you know, thickened herbal juice has excessive resistance.

The lubricant for the gearbox of the trimmer for the grass is selected based on many parameters described above. Carefully consider all of them, and then the device will serve you regularly for a long time, always delighting with a trimmed lawn and a well.cleaned territory.

With frequent, intensive use of motorcycles, the gearbox can start to heat up or make sounds uncharacteristic for its normal operation, for example, rattle. This indicates that the mechanism must be lubricated. If this is not done on time, then more serious problems will arise (for example, gears will be quickly worn out and you will need to replace them), up to jamming. Other breakdowns also arise with the transmission mechanism. Reducer repair and lubrication can be performed independently. for this you just need to familiarize yourself with the features of these work and stock up on some available tools.

Lubrication of the lower gearbox Motokos

The coil gearbox is recommended to lubricate every 10 hours of work. The best lubricant for him, as well as for the shaft of motorcycles, “shus-4” or “litol-24”, designed to work at high temperatures.

To add lubrication to the lower gearbox, we use a disposable medical syringe with a capacity of 5 or 10 ml without a needle:

• We remove the piston from the syringe and disconnect the needle if it was attached.
• Add to the syringe from the piston side the required amount of thick lubricant “shus-4” or “lititol-24”.
• We insert the piston into the syringe and shift the lubricant to the output (drive air).
• The tip of the syringe without a needle is inserted into the lubricant hole and squeeze out the lubricant into the gearbox.

In my guide of the user’s user trimmer for gasoline grass PRORAB 8402R, 8403R, 8405R, 8406R it says that the use of motor oil for two-stroke engines in the amount of 20-30 ml is allowed as a lubricant for the gearbox. But this is not the best option, since the gearbox does not have sealing oil seals and motor oil flows faster than thick lubricants.

Sometimes it is recommended to lubricate the coil gearbox, disconnecting it from the bar, and adding grease until it starts to squeeze out of the gearbox through the coupling. A good option if the gearbox is not removed specifically, but, for example, during the lubrication of the shaft of the lawn mower.

When I disconnected the lower gearbox at the new trimmer for the Hopper VS-350 4T, to remove the burrs at the bar and grease the shaft before starting operation, I noticed that the coupling was flooded with a thick lubricant that was squeezed out of the gearbox. This tells us that there is a lot of lubricants for the gearbox and you can not limit ourselves to the recommended 20-30 ml

The device and principle of operation of the starter on the trimmer

Gas engine. This is, in principle, the main part of the brush. Its power is in the range of 0.5-2.5 liters.FROM. Movement from it is transmitted to the shaft located inside the hollow rod, and then through a gearbox, consisting of gears, already fishing line or knife (working body).

Bigorezes also have the following elements:

• Corrugated board;
• Lever arm;
• A belt designed for simplicity of using the device;
• Starter used to launch an internal combustion gasoline engine.

All details of the brush are presented in the photo below.

The trimmer starter is an integral part that launches the engine. This is shown separately in two photos below.

The starting mechanisms of different models of gasoline bite to work on the same principle: when starting the internal combustion engine, the protrusions indicated by the number 1 in the photo above are included in the hook with dogs 3. When the engine is launched, they return to the previous position due to the action of centrifugal. A similar role is played by wires 2.

The process of returning to the initial position of the elements of the mechanism is due to the presence of a spring wound around the axis. It turns around when the rope is pulled. After the release of the cord, it is pulled and assembled by a spring. When the internal combustion engine starts, the trigger rotates its shaft until it starts (does not start).

To date, the starting mechanisms of two types are equipped with gasoline scooters:

The first option is much more common.

A trimmer starter can work for a long time without breakdowns. It is impossible to unequivocally indicate the period of continuous time. Everything is determined by the initial quality of the device and compliance with the rules of handling it.

What lubricant should be used for a trimmer gearbox for grass?

In the process of work, the mechanical part of the trimmer for grass is loaded with contact efforts on the teeth, resistance reactions from adhering grass (sometimes with dirt), dynamic, shock loads due to a constantly changing torque. The lubricant for the gearbox of the trimmer for the grass should fully consider these features, so the selection of the brand should be strictly individual.

The following factors are taken into account:

• Manufacturer’s brand. Each trademark is not unreasonably focused on lubricants of its own manufacture (you can talk about cheap Chinese products later). This applies to manufacturers such as Husqvarna, Stihl, Huter, Makita, etc. The exception is trimmers for domestic grass: for example, the caliber in the user’s instructions does not indicate a lubrication brand at all.
• Break of lubrication. As you know, all lubricants are divided into three groups. high.speed (colloidal systems containing various additives), plastic compounds of universal use and hard lubricants softening during operation.
• Good adhesion to the surface of the parts of the gearbox, as a result of which the lubricant is not squeezed into the gaps or outside the node.
• The intensity of lubrication consumption by the gearbox. Here you have to focus on their own experience and recommendations of specialists, since some manufacturers of trimmers, hoping for their own service centers, do not give clear recommendations at all regarding the period of the reducer between two lubricants.

The consumption of the lubricant also depends on the temperature at which it retains its lubricant. When heating the gearbox to 40 ° C, it is believed that its working conditions are satisfactory, and there are enough lubricants.

It is believed that there is no universal lubricant for the gearbox for grass, but this is not entirely. In fact, a suitable lubricant will be the one in which the following components are present:

• Anti.sympathetic supplements, which include toxic lead;
• Solid lubricants with the presence of graphite or disulfide of molybdenum (the latter is preferable, since the lubricant is completely preserved for the large range of the speed of the shaft);
• Only mineral (inorganic!) oils, with a high degree of cleaning.

The mentioned requirements are fully met by Gear Grease Oregon or Champion EP-0, domestic compositions Oleo-Mas, Litol.24, or Ammol 158, as well as those recommended by the manufacturer of a particular model of a trimmer for grass.

How to lubricate the gearbox of a trimmer for grass?

In the upper part of the case, where the gear unit is installed, there is a technological hole that, when operating the trimmer for the grass, is drowned out with a screw. This screw is twisted, and 1.5 2 ml of grease is introduced into the hole using a nose available on a tube. If the lubricant was purchased in another packaging, then a regular disposable medical syringe is suitable for this operation.

After that, the screw is installed in its former place. This procedure, regardless of the user’s recommendations, should be performed every 10 15 hours of operation of a trimmer for grass in working mode. Other reasons for updating or replacing the reducer lubrication are the independent performing of small regulatory work (for example, cleaning and washing the gear of the gearbox before the start of the summer season), repair of the node, preserving the trimmer for grass for the winter period, etc. D.

If the reducer node is disassembled, it is recommended to completely remove the remaining lubricants from the surface of the parts, even if it does not have traces of oxidation and pollution. And only then apply a new grease. After applying the lubricant, it is recommended to handle the shaft several times manually, and make sure that the grease is evenly distributed over all the details of the gearbox.

When lubricating, special attention is paid to the following elements:

• Flywheel: on its surface, as a rule, intensively sticks the remnants of grass, and thickening herbal juice creates additional resistance.
• Dog of a starter coil, which in the process of turning on the drive is constantly in contact with the grooves on the flywheel. At the same time, not only mechanical wear occurs, but also the mechanochemical corrosion of the Makhovik-Sobachka compound, since the materials of this pair are different (the flywheel is aluminum, and the dog is steel).
• Bearings, if their seals are worn out, and through them the remaining lubricants are squeezed out. In this case, the unit begins to vibrate intensively when loading. This happens with trimmers of Chinese.made, so it is worthwhile to think about replacing a bearing unit with a better, for example, from the Swedish company SKF.

Patriot trimmers are a vivid demonstration of American production of garden tools

The products of the famous American brand Patriot have their positive features that attract the attention of more and more users. Despite a huge number of competitors, the company still manages to actively stay afloat and develop, constantly delighting the fans of the brand

Having originated in 1973, the organization passed a lot of tests in its path, but it coped with all of them perfectly, so today it flourishes, offering a wide variety of horticultural products only of high quality.

Patriot trimmers were awarded special attention, because they comply with the current safety rules, differ in a well.thought.out assembly, considerable power and considerable endurance. What else is gardeners need? Nothing!

What trimmers for Ratriot grass will be the best to demonstrate the strengths of the brand? Now we will consider them/

Features of the unit:

• The presence of the anti.vibration system AVS;
• Easy access to the spark plug;
• Adding the casing with a knife that allows you to get rid of the excess fishing line;
• The possibility of light and quick repair of an air filter with your own hands;
• Affordable cost;
• Light weight.

Due to the serious engine power (1.3 kW), the device copes even with dense and thick weeds.

Patriot RT 555 lawn mower

The machine was equipped with a specialized anti.vibration system, which provides ease of operation and creates comfortable sensations during operation. The handle contains all the necessary control elements. The device starts very quickly, because the mechanism contains a special ignition coil and is supplemented by a primer.

What oil to choose for refueling in a trimmer for grass or types of lubricants

Trammers for grass and lawn mowers operate on two.stroke engines that have a simplified design. Rarely, but there are models of trimmers with 4-stroke engines that work on pure gasoline. Two.stroke.type power units do not have a compartment for pouring motor oil (oil crankcase), due to which the weight of the tool is reduced and their cost is reduced. If the rotating details of the motor are not lubricated, then in the end they will quickly fail. To prevent this, a trimmer for grass is seasoned not with clean gasoline, but a mixture with butter. What kind of oil to dilute with gasoline for a trimmer for grass?

First, remember or find out what types of oils are produced by chemical composition:

• Mineral fluids. designed for small power technology, which has air cooling. This is the cheapest type of lubricant for motors
• Semi.synthetic substances. they are used for technology, which has air and water cooling
• Synthetic. suitable for all types of motors with different types of cooling. They do not require frequent replacement, and this type of lubricant is several times more expensive than mineral and semi.synthetic

It is interesting!The main thing when choosing oil is not to fall on the fake, since today you can very often find different types of lubricants for two.stroke engines, which consist mainly of low.quality oil products.

How to fill in the finished fuel on a two.stroke motor

Many do not comply with some important recommendations for pouring fuel in the gas tank of the trimmer for grass or lawn mowing, which ultimately leads to unpleasant consequences. Consider important recommendations on how to properly fill in the gas tank of motorcycles diluted fuel from gasoline and oil:

Prepare a funnel or watering can. Despite the large diameter of the hole of the gas tank, very often when trying to get into it, a certain part of the fuel is spilled, which enters the tool case

The fuel that came to the tool can cause ignition when heated, so it is very important to use a funnel or a watering can before twisting the cork, you should carefully clean the surface of the tank, since pollution can get inside, which will cause a quick clogging of the fuel tanker should be carried out in the calm The weather or in a secluded place to exclude the likelihood of dust and small grains of sand inside the tank do not leave the open hatch of the tank for a long time, since not only small grains of sand and dust can fall into it, but also insects do not inhale gasoline vapors during filling, Since they are dangerous for humans. When working with a trimmer, the master should use protective glasses, headphones and a respirator to pour fuel into the tank, you need to mark before the mark

If you pour a full tank, then with screwing the cork, some will result in a non.excessive use of fuel. In this case, it is better to shorten than to pour

Given these recommendations, you can significantly extend the service life of the gasoline tool in question.

It is interesting! Work on the preparation of the mixture and pouring fuel is also recommended in protective gloves.

Huter 2T 1 L

The semi.synthetic oil of this manufacturer is well compatible with the engines of gasoline trimmers and chainsaws, as well as scooters, motorcycles, scooters and other equipment. Provides reliable protection of a two.stroke engine when operating at high speeds and is suitable for a separate or mixed lubricant system. It is recommended to fill this oil to reduce the risks of jamming of the piston rings and reduce failures in the spark plugs.

The lubricant for a 2-stroke engine of this brand reduces the appearance of corrosion, removes the soil, does not allow the formation of deposits, which reduces the load on the structural elements of the engine and the equipment in general. Buyers note that this semi.synthetics does not lose its functionality at low temperatures, requires less replacement than mineral analogues, boasts high fluidity and the optimal level of viscosity.

The proportions of the fuel-oil mixture for two-stroke trimmers

Accurate oil dosage is a guarantee of reliable work of the trimmer for grass. Some Chinese manufacturers recommend observing 1:25 proportion, but brands such as Husqvarna or impeccable stihl, directly recommend filling oil in a ratio of 1:50. We can say from ourselves that the recommendations of Chinese comrades are quite relevant in the first hours of the trimmer for the grass. in the process of running up, all the rubbing steam is laid, and the excess of lubrication will not be superfluous. But when the device is already driven and works “to the full”, it is better to observe generally accepted proportions. For convenience of calculation, we suggest using a small table. It can even be printed and glued to a container with butter, so as not to spend time on counting. In this case, never prepare a mixture with a margin. it is better to make small portions that are guaranteed to be developed.

Chevrolet Captiva Club

Sych Marshal Captiva Posts: 5368 Registered: 21 Dec 2013, 19:43 City: Better the most car: from 140 dti LT 2012 Mathered (A): 2 times thanked: 8 times: 8 times

Andreil Marshal Captiva Posts: 15038 Registered: November 21, 2013, 15:31 City: Yekaterinburg Auto: C140 2.4AT LT 2013.in. (Feyslift) thanked: 283 times thanked: 296 times

t.e. The canister shows the proportions for running and after?

Any for 2 stroke engines or one that is not sorry for the money

h.s. I do not like these 2 huscons: you overcome oils. smoke, do not share. you can start a motor

QUANTEGY Major General Messages: 2054 Registered: 13 Apr 2014, 11:58 City: ECB Auto: C140 LTZ thanked: 6 times thanked: 4 times Contact information: Contact information: Contact information: Contact information: Contact information:

VLZZZ Lieutenant Colonel Message: 1394 Registered: 17 Dec 2013, 18:24 City: G. Volzhsky, Volgograd region.

VLZZZ Lieutenant Colonel Message: 1394 Registered: 17 Dec 2013, 18:24 City: G. Volzhsky, Volgograd region.

Alexandr78 Major Messages: 775 Registered: February 13, 13:16 City: St. Petersburg thanked: 1 time

Andreil Marshal Captiva Posts: 15038 Registered: November 21, 2013, 15:31 City: Yekaterinburg Auto: C140 2.4AT LT 2013.in. (Feyslift) thanked: 283 times thanked: 296 times

I have no 2.clock engines. “Water Technique” and “Motolopata” 4th stroke

Black451 General Captiva Posts: 3852 Registered: 01 Jan 2015, 23:41 City: Peter Auto: C140 2.4 MT LS thanked: 159 times thanked: 98 times

I have a scythe for Hitachi grass, it is very convenient. Benz was flooded and forward, no dancing with a body of fuel.

As I understand it, for this 2t crankcase engine, no lubrication is made of diluted oil in fuel.

Thanks to all the respondent advice)). As a result, I ordered a Castrol Power 1 2T (15940B) for running.in. it turned out to be cheaper Khuskvarna or STIHL

Which oil is better to use for a trimmer for Patriot grass

The fuel mixture for the chainsaw is prepared from two components. Oils and gasoline.

Motorcycle oil. How to choose in what proportions to breed

If we talk about which gasoline is poured into a chainsaw, then the use of octane fuel is optimal. In this case, fuel saving may be bad. Often, European manufacturers indicate that gasoline A or A can be used, but in post.Soviet countries, the quality of gasoline is inferior to European, so in our realities it is better to use better gasoline. As for the proportion of mixed benzoil, everything is simple: you must follow the instructions for the tool.

All manufacturers of chainsaws indicate the required ratio in the instructions for operation or in the passport of the device, in addition, the proportions for refueling chainsaws may vary depending on the model of the chainsaw.

As a rule, the ratio of oil and gasoline to the chainsaws of well.known manufacturers is a ratio that means 1 part of the oil, for example, for 40 parts of gasoline. If we follow the same steps to the ratio, we get 20 ml of oil per 1 liter of gasoline.

As for budget chainsaws made in China, the situation is somewhat different. The ratio of gasoline and chainsaw produced in China is divided into 25 ml of gasoline, 40 ml of oil is obtained.

The fact is that branded chainsaws have a good assembly, and the distance between pistons and cylinders in the engine is much less than Chinese chainsaws, so the required amount of oil is almost half. To measure the right portion of oil, use the usual medical syringe sufficient volume. Another subtlety is to fill gasoline into a cancer with dry gas, and then in oil.

The procedure, on the contrary, threatens a poor fuel mixture, since the oil is more dense, sticks to the bottom of the canister. What is a good mixture. Be sure to prepare the fuel mixture in cans and pour special fuel into the tank! Never cook or mix directly in the fuel tank of the chainsaw!

If you find out how to dilute gasoline for a chainsaw, you should say a few words about storage conditions and shelf life of the fuel mixture. It is best and easiest to prepare a 1-liter gasoline-oil mixture, it is recommended to do this immediately before working with the tool. Fuel tanks of chainsaws have a capacity of 0.3 to 1 liter. With domestic use, the entire volume of the prepared fuel mixture is rarely used in one session, so the remainder can be stored until the next session.

It is necessary to store the fuel mixture in a special canister for gasoline, in a dry place protected from light. It is best to expect that the shelf life of the finished mixture will be several days. The fact is that the oil is currently not synthetic in the market, but organic, that is, natural.

Features of the gas station

Welding apparatus welding rectifiers inverter semiautomatic devices devices for point welding cutlets Welding semiautomatic devices Welding transformers Equipment for gas welding gas burners of gas welding gas solders gas gearboxes.

Accessories of accessories Output equipment Holders of electrodes welding cables Mass terminals of lamps for soldering Tips for sleeves gas cans sleeves for semiautomatic welding magnets of nozzles How to dilute gasoline for a trimmer for Patriot sleeve oxygen hoses. Consumable materials gas cans soldier for soldering welding wire welding electrodes.

Pneumatic instrument pneumatic grinders pneumatic drills Pneumatic drills Pneumatic drills Pneumatic rivets compressors Pneumatic lubricant pneumatic hammers pneumatic scissors pneumatic pneumatic staplers Pneumatic template pneumatic template pneumatic pneumatic. Accessories Consumable Materials Aerialoths Manometers Pneumatic Pistols Pneumatic Reductors filters for pneumatic instruments Pneumatic hoses Connection fittings.

Consumable materials compressor oil clamps for staplers. Manual tools sets Knocks sets sets Key sets chick tough sets taps and stamps sets sets sets sets Supplows sets sets sieves tough sets of hinged heads of the bag of bags.

Tools of tools for cars of outlets tools tools tools Tools sets Sluds Fasteners sets fasteners Equipping one hundred Goroscopes compressors.