Manual for chainsaw Stihl 180

Cutting attachment and guide bar installation

In these sections, instruction 180 is devoted to the saw headset and how to properly install it on the saw. Chain links, chain tension, protection and much more, which will be useful to everyone who deals with the tool.

The most important information from the section can be considered how the tension is controlled, and what precautions must be taken to avoid injury from sharp saw teeth.

Starting and stopping the engine

One of the most important points that the 180 instruction contains is starting and stopping the saw motor.

Unboxing and assembling Chainsaw STIHL MS 180 in 2 minutes. Bob The Tool Man

According to unofficial data, most calls to the service center with STIHL chainsaws sold within a month are due to a violation by the owners of the STIHL 180 chainsaw start algorithm.

The manufacturer has taken all possible measures to reduce the statistics. I wrote detailed instructions and organized mandatory consultations during the sale. But users do not want to read the paragraphs on starting a chainsaw and listen to sellers, which, as a result, leads to an increase in the number of calls to the service center.

The start section also contains the main provisions in which it is most convenient to start the saw, and at the same time to protect yourself as much as possible from getting all sorts of injuries.

You can watch a video on starting a chainsaw, which shows in detail in what position the control lever should be located, for different modes of starting the saw.

Instruction manual for chainsaw STIHL MS 180

The STIHL ms 180 chainsaw comes standard with an instruction manual.

Due to the fact that its development was carried out by the professionals of the German company STIHL, the manual for the chainsaw is written very competently and covers all the main points of operation. Let’s look at some points of the instruction from which the saw owner can get the most necessary knowledge.

Final points, which contains the instruction of the 180th

In the final part of the article, German engineers have concentrated the most complete information on the maintenance of the chainsaw.

So at the end, the instruction contains the following sections:

  • tire maintenance;
  • cleaning the air filter;
  • carburetor setting;
  • spark plug;
  • storage;
  • control and replacement of the drive sprocket;
  • all information related to technical information about the saw.

A large section is devoted to chain sharpening. You can even say that you will not be able to find more complete information about sharpening, the choice of files and auxiliary tools anywhere except in the STIHL manual.

The STIHL manual is a document that is unique in terms of the information collected in it, which will be most useful for reading both for people with no experience, and for owners of chainsaws with decent experience.

Reaction forces

The paragraph of the instructions following the safety section, at first glance, attracts attention with a picture. The information that can be obtained by reading the section “Reaction forces” is probably unfamiliar to all those who do not read the instructions for STIHL chainsaws, but prefer to immediately start operating.

In turn, those who read it will receive several unique recommendations and tips to reduce the recoil of the chainsaw and the risk of rebound and find out why the chain brake has exactly this shape and location.

Safety instructions

This section contains basic recommendations for the correct and safe operation of the STIHL 180 chainsaw.

From the section you can find out what personal protective equipment should be used when working with a saw, how to transport and clean it. A separate item highlighted safety when refueling the STIHL 180 chainsaw.

Another important subsection of safety is precautions and proper behavior when working. The most important points are marked with special signs that attract attention and emphasize the extreme importance of information.

Fuel and refueling

How and what to refuel the tool, lubricate the chain and the consequences of using low-quality fuel, this is what you can learn from these sections. In fact, many people think that there is nothing to know there, but this is fundamentally wrong, since in this section the 180th instruction contains a lot of useful information.

  • the proportion of the fuel mixture;
  • replacement of the fuel filter;
  • storage of the finished fuel mixture;
  • preparing your STIHL chainsaw for refueling.
Read more:  How To Set Up A Chainsaw Carburetor? Recommendations.

Reading and refreshing knowledge will be useful even for those who have extensive operating experience.

Technique of work

This section will be useful for those who first pick up the STIHL ms 180. The technique of cross-cutting, cutting a felled tree and the felling process itself are touched upon and discussed in as much detail as possible.

I would like to note that some points of the section, concerning, for example, cutting trees in a certain direction, cannot be found in the operating instructions of other manufacturers of chainsaws, it is for this reason that the 180th manual is unique in its content.

After reading the section, you can learn how to properly cut a tree trunk, how to cut branches and the main points regarding safe work. over, all these recommendations and methods are drawn up with the help of numerous drawings and drawings, reflecting the essence in maximum detail. Thus, the section will be understandable even for people who have never had experience using a saw.

The STIHL 180 chainsaw belongs to a household tool and, while developing the instructions, the manufacturer took care of inexperienced users and tried to make it as detailed as possible.

Saw starter

The main cause of breakage is a broken cord. It is necessary to remove the saw cover, unscrew the 4 screws securing the starter. Replacing the cord is not particularly difficult. The condition of the remaining parts of the starter can be checked immediately. Before assembling, we lubricate the moving elements and clean them of dirt, oil leaks. You can change the entire starter.

manual, chainsaw, stihl

Engine and clutch

Before repairing the engine, make sure you can do it yourself without going to a service center. If you still decide, you need to disassemble the engine. To do this, unscrew the four nuts that secure the cylinder. We check it and the piston for cracks, chips, scratches and wear. We purchase a piston repair kit and make a replacement. After assembly, it is necessary to run in the STIHL chainsaw.

Clutch problems are due to dirt or wear. A similar malfunction manifests itself in the constant torsion of the drive sprocket or extraneous noise in the gearbox. The reason may be worn or broken springs. Sometimes the clutch cams split when the chainsaw overheats. The problem is eliminated by replacing the clutch.

You can watch “The STIHL 180 chainsaw does not start video reasons”:

Ignition system

The saw will not start very often. The reason for this may be a breakdown in the ignition. To diagnose and eliminate the cause, it is necessary: ​​remove the protective cover, remove the air filter (it closes access to further actions) and the tip from the candle. We unscrew the candle with a special key (usually comes with a saw) and check it.

STIHL 180 How to start a chainsaw. Starting the Stihl MS 180 chainsaw. Engine start stihl ms 180.

It is necessary to clean it from possible carbon deposits. It is necessary to pay more attention to the electrodes, to clean not only the working surface, but also inside the skirt of the candle. You also need to check and adjust the gap between the electrodes. After that, we check for a spark. You may need to replace the spark plug or high-voltage wire with a spark plug tip.

If an oily coating forms on the spark plug, an excess amount of fuel enters the cylinder. The carburetor needs to be adjusted. After all these manipulations, you can start the saw and check its performance.

Device description and technical parameters

STIHL 180 comes standard. However, like all modern chainsaws. Its components:

  • Anti-vibration front and rear stick.
  • Saw bar with chain.
  • Two-stroke single-cylinder engine.
  • Fuel and ignition systems.
  • High quality plastic housing.

Chainsaw STIHL 180, specifications:

  • Gasoline engine that runs on a mixture of fuel and oil in a ratio of 1: 50. It has a capacity of 2 liters. from.
  • The saw weight is approx. 4 kg.
  • The saw is equipped with an easy start system.
  • The capacity of the fuel and oil tank is 250 and 140 ml, respectively.
  • Saw bar is 14 inches (35 cm) long.
  • Automatic chain lubrication.

Fuel problems

Malfunctions associated with the intake and combustion of fuel in the cylinder are most often associated with improper operation of the carburetor. Typically, such a malfunction manifests itself in the form:

  • The engine starts poorly or does not start at all.
  • Interruptions in work, when you press the gas, the engine “swells” and stalls.
  • Too high idle speed, the saw “roars”.
  • Increased gasoline consumption.
  • The saw does not develop the speed well.
Read more:  Chainsaw Oil Which To Use

It is not difficult to adjust the carburetor of the STIHL 180 chainsaw with your own hands. It has 3 adjusting screws. One is responsible for idling, and the other two for fuel. Usually a simple adjustment is enough to get the saw working again as expected. If this does not happen, then the carburetor should be cleaned with its complete disassembly.

The fuel filters, breather and tank should also be flushed before completely cleaning the carburetor. Otherwise, the entire system will clog again. For some reason, most people only flush the carburetor and ignore the rest of the fuel system. It is best to disassemble and adjust this element using the standard manual “Chainsaw STIHL 180 operating instructions”.

This manual describes in detail the diagram of the carburetor device, which has a difficult detail.

Basic malfunctions and repairs of the STIHL 180 chainsaw

An excellent choice among all chainsaws is the STIHL 180. The best in its segment, both in price and in the work performed. Compact, lightweight, economical, unpretentious and reliable tool. In fact, this list of positive qualities is quite long. Even so, malfunctions and repairs are an integral part of the STIHL 180 chainsaw. It should be noted that this problem with Calms, unlike other brands, occurs much less frequently.

Chain lubrication

This usually occurs due to a clogged lubrication system. We clean the oil pump from dirt. The oil supply to the chain can be adjusted. To do this, turn the screw to the side. which is next to the leading sprocket. To check the oil supply, the saw must be started. We bring the tire to any unnecessary surface and give revolutions for the movement of the chain, where an oil trace should remain.

This problem does not affect the operation of the chainsaw. But the bar and the chain must be lubricated, otherwise it will lead to more serious damage.

General recommendations for use

When buying a new chainsaw, you need to run it in. When operating in cold seasons, the engine must be warmed up before intensive work. During work, do not overheat and take breaks to cool the saw. You need to do everything correctly and monitor the oil and fuel level. Sometimes users have a question, what other oil can be used for this saw? Do not fill in other brands of oils, but use only the one recommended by the manufacturer. Do not disturb the fuel ratio. Do not use longer saw bars, this will not have much effect, but will cause intense wear on the chainsaw.

Reviews about chainsaw STIHL 80 ms

Svyatoslav:

“I can say that the chainsaw is good! It was acquired in 2015. No serious breakdowns happened. Due to the fact that I often used it, the candle has already been replaced several times. And I can note that this compact chainsaw is capable of performing large-scale work, despite its modest parameters and dimensions, its power corresponds to some professional saws.

Advantages: when the season for harvesting firewood is, she cuts me for 3-5 hours, the weight is small, excellent assembly and all the parts are very high quality. It is convenient to work with such a saw, the handles do not slip in the hands. Running in a STIHL chainsaw ms 180 is as easy as two and two! Performed according to instructions. 5 working hours.

Disadvantages: if you need to constantly saw something, then take STIHL from the professional series, more powerful. This chainsaw is even noted in the manual as a tool for periodic use. “.

Also on the pages of our blog you can read articles about:

Saw varieties and specifications

The demand for STIHL mc 180 chainsaws among amateurs is due to the ease of operation and reliability. The base model weighs only 3.9 kg. Saber, blade length 35 cm allows you to saw logs or drop trees with a cross-section of up to 30 cm. Two-stroke engine power 2 hp. with., which allows you to perform all household work related to cross-cutting boards and even firewood from any tree species. The capacity of the fuel tank is only 0.25 liters, but this allows you to work without stopping for 45-55 minutes.

A mixture consisting of the recommended or transmission oil with unleaded AI-92 and AI-95 gasoline should be used for refueling. The ratio is 25 ml of additive per liter of gasoline.

The STIHL 180 chainsaw chain is an endless endless loop of 50 links. Other parameters:

  • chain pitch. 3/8 inch;
  • groove width. 1.3 cm;
  • material of manufacture high-carbon steel, chrome-plated steel, victorious soldering.
Read more:  What should be a chain tension on a chainsaw

Working mechanism, saw headset, includes bar, sprocket and automatic lubrication system.

The chain tensioning system is located on the side, which is convenient. Chain brake provided.

Depending on the length of the tire and the modernization of the STIHL MC 180 chainsaw, there are several modifications. Saws with a saber length of 35 cm refer to models in the marking of which there are 14, their length in inches is 14. The same equipment for the engine and its parameters, but with a tire length of 40 cm, is called MC 180 16. Chainsaw STIHL mc 180 С- BE instrument is of a higher class. It contains a 40 cm long tire bed, an easy starting system, and a quick chain tensioning system. Easier access to the air intake filter, a condition that prolongs the life of the tool.

DIY saw repair

With the advent of the light and convenient STIHL MC 180 chainsaw in the household, it will completely replace the two-handed, bow and even hacksaw. Over time, the chains become dull, the sprockets wear out, the oil supply system is damaged. You can fix some problems yourself. Others require repair at special service centers.

You can check if there is grease in the reservoir, and if it enters the chain, using a clean sheet of paper. Direct the tire at a sheet of paper, it should leave a characteristic trace in the form of an oil strip.

You can repair the saw yourself only after understanding the arrangement of the units and the sequence of operations for removing and restoring or replacing the unit. The STIHL 180 chainsaw operating instructions will become a reliable assistant. It is in it that you can find installation techniques and a sequence of repair operations:

  • oil supply systems;
  • bringing the carburetor into working condition;
  • repair or replacement of the oil pump.

In addition, the DIYer can shorten the stretched chain and sharpen it.

If the saw chain remains dry during operation or oil leaks, it means that the malfunction and repair of the lubrication system of the STIHL 180 chainsaw is required. At the same time, the oil lines and the tightness of the connection with the fittings are inspected. The filter on the oil supply must be cleaned. If the hoses have minor mechanical damage, the tightness can be restored with a sealant.

The carburetor makes itself felt by the difficulty when starting the saw, the running tool does not gain momentum, stalls when throttled. The reason may be the wear of the cuff on the piston, as a result, air is sucked in when discharged. For repair, the carburetor is removed and the cuff is reached on the accelerator, disassembling the assembly in the sequence:

  • remove the cover with the membrane by unscrewing the screw;
  • remove the retaining ring;
  • disconnect the air damper, remove the throttle;
  • pull out the accelerator with the spring;
  • replace the tiny cuffed piston and reassemble the carburetor in reverse order.

Problems may be related to the ignition system. After checking the performance of the candles and cleaning the carbon deposits, adjust the carburetor, supply system and clean the injections. The carburetor is a complex unit and the operation of the chassis depends on its setting. If there is no confidence and skill, it is better to use the services of a specialist. Often, work on low-quality gasoline, with not recommended oil is the root cause of all problems.

To help the master, there is information on the resources on how to repair a STIHL 180 chainsaw with your own hands, for example, a video will show the disassembly sequence.

For diagnostics of the lubrication system, see here:

Ematic chain lubrication system

The STIHL Ematic system consists of an Ematic guide bar, an Oilomatic saw chain and a variable-flow oil pump. The special design of the bar and chain makes every drop of oil go exactly where it is needed for lubrication. This reduces oil consumption by 50%.

How to start a STIHL 180 ms chainsaw correctly:

manual, chainsaw, stihl

Video

Advanced modification ms 180. STIHL chainsaw ms 180 c be

For neat storage and transportation of chainsaws with bar lengths up to 45 cm (not suitable for electric and MS 441, MS 461, MS 661 C-M and MS 880 chainsaws).

Execution options

Recommended manufacturer price as of 09/01/2020. The manufacturer’s recommended price is not included in the promotions.