The chain on the chainsaw was stretched out what to do
You can shorten the chain of the chainsaw with your own hands using simple tools. This method is less reliable, but easy to use, does not require special skills in working with cloth equipment. Disadvantage. you cannot control the strength and quality of crushing rivets. This can lead to a breakdown of the tool with serious loads.
How I Achieved Full Splits In Only 1 Week. Fast Flexibility ASAP (Full Routine)
What tools will be needed for repair at home?
You can work with the help of the most affordable tools. Depending on the skills and skills, it may be required:
Some masters also use an electric welding machine. It is not recommended to use it, since the seams after welding quickly become unusable under the influence of vibration during intensive work of the chainsaw. This method is suitable only for gearbox chains that transmit efforts to the leading star.
Removing rivets
To disconnect the links, it is necessary to apply physical effort, since high.quality steel is used to manufacture the headset. Before starting work, the circuit is firmly fixed in a vice in order to avoid injuries during the removal. Stack the protruding part. Do.it.yourself rivets itself can be removed in the following ways:
Continue to grind with emery until the jumper. Attach the beards, hide the metal with a hammer. Stream rivet corner grind. Disadvantage of the method. you can damage the chain itself
Work should be carried out carefully, periodically wetting the area with water. After squeezing the chain in the vice for the guides, cut the rivets with a chisel
If you need to increase the number of links or remove one of them, then you need to remove at least two rivets (left and right). When using a corner grinder, the metal can heat up, so after grinding you need to wait for cooling or work in protective gloves.
Connection of links
You can purchase a new link for any chainsaw model in any specialized store, remove it from the old headset. The use of donor spare parts is not recommended, since the quality of the cutting canvas is reduced from this. Installation technology:
- Install the link with new rivets on the chain. Put on the anvil with an open side up.
- Put the top plate on the rivets, stick a hammer for a tight connection several times.
- Attach the beards on the rivet, make 1-2 strong beats with a hammer. Achieve a pronounced thickening, flattening metal. Repeat the operation on both sides of the link.
After work, it should be checked that the chain is mobile, all its elements go freely in different directions. This avoids jamming during sawing.
How to dress and pull the chain correctly?
Before starting work, you should put on gloves to avoid cuts about sharp teeth. Only a cold chain can be pulled. after cooling, it can burst from overvoltage, damaging the mechanism
Remove the protective casing from the chainsaw, carefully put it on the tire
Depending on the configuration of the tool model, the tension is given manually or using a special regulator. In the first case, you need to loosen the bolts on the tire, after installing the circuit, give the voltage using a slotted screwdriver. If there is an adjusting bolt, then turn it all the way until a sufficient tension of the canvas appears. After work, check the absence of sagging, be sure to tighten after the first operation.
Constructive features of tensioners of chainsaw chains
To adjust the degree of tension of the chain on the chainsaw, the design of the tool has appropriate adjusting screws. The first two screws, through which the tire is attached, allow you to carry out a rough setting of the degree of tension.
To set the exact tension of the headset, the tool design has a special screw. This screw is connected to the tire tension mechanism, during the rotation of which a more accurate setting is carried out. To ensure gross adjustment, it is necessary:
- To strengthen the stretch, it is necessary to move the tire away from the asterisk.
- To loosen the tension, you need to move the tire to the side to the leading star.
The mechanism of the chain tensioner has a simple design consisting of a screw with a thread on which a spike and a gear are located. This spike is included in the hook on the tire, and affects it when moving the screw. The gears are designed to transfer the force when rotating the adjusting screw to the screw. The simplicity of the design of the adjusting mechanism affects its reliability. On a chainsaw, this mechanism is extremely rare, but even if this happens, then the part is inexpensive.
The tension mechanism on the chainsaws of different manufacturers can differ in design, only the principle of operation for all devices is the same. The difference in the design of the mechanism affects the location of the adjusting screw, which can be located on the side (the most common option), from the end part or below. over, the screw hat can have a direct shape for a slotted screwdriver or hexagon.
Diagnosis and proper care of the chain of chainsaw
The productivity of the chainsaw depends on a number of factors:
If the degree of stretch affects the performance of the chainsaw, then the sharpening of its teeth is on the speed of sawing
Therefore, it is extremely important to pay individual attention to this moment. With good sharpening of the teeth, the cut is much more effective, more precisely and safer
The regularity of the sharpening procedure has no special standards, but professional rollers recommend performing it several times a day. This is due to a fairly rapid gear in the process of intensive sawing.
Most often, the degree of closing the chain is determined with the focus on the performance of the chainsaw. In addition, the tool needs sharpening when the bus begins to take aside. Another gaze measure is the state of the shavings. As a rule, from properly sharpened teeth, the chips are homogeneous. In this case, the sawdust has a rectangular or square shape. In the case of a blown chain in the chip, dust will prevail, and the sawdust will resemble the shape of a needle from a simple hacksaw.
If you regularly monitor the degree of tension of the chain and tighten it in a timely manner, the chainsaw will last for a long time. At the same time, the process of sawing even with particularly solid wood will not cause you trouble.
In case of insufficient experience, it is recommended to consult a specialist. Professional lumberjacks determine the state of the chainsaw and its components during the first inspection. They will determine the degree of its wear, too tight the tension of the chain and the severity of the teeth.
Strong wear of the saw canvas
The tire serves much longer than the chain. However, this does not mean that it can be exploited forever, and not think about replacing it. Usually the guide changes after 2-3 worn chains. Before replacing the guide chainsaw, you need to evaluate its technical condition. If the tire of Chinese.made is installed on the chainsaw, then it can be worn out faster than the chain. That is why if the crooked cut of the wood of the chainsaw is detected, it is necessary to diagnose the tire.
To verify the wear of the tire, it is necessary to remove it and inspect it. Usually wear is manifested by a shortened one of the sides. Sometimes it is extremely extremely difficult to detect, so you need to use a caliper. The difference of several tenths of MM suggests that the tire needs to be replaced. There is still a simple way to check the deployment of the guide using a square. For this, the tire is located on a flat surface, and you need to put a square to the side. If the guide walls are in contact with the square from above and below, then the part is serviceable.
It is interesting! It is possible to increase the service life of the guide chainsaw only by periodic turning it. To do this, be sure to make sure that the tool provides such an opportunity, which will tell the appropriate markings on the headset about.
Accelerated tire wear can occur due to improper functioning of the oil pump. If the lubricant is served with large breaks, then friction increases accordingly, which means that the details wear out faster. If the lubricant works properly, then this increases the service life of not only the headset, but the entire tool.
How to install a tire with a chain on a chainsaw?
Often the obstacles of the chainsaws appear when the tire is incorrect. This can be found according to the appropriate rattling, vibrations and low sawing of saw in working hours
The tire attachment to the case is between the external plate, fixation is carried out by a special bolt.
The people call this part “engine knot”, it consists of a drive star and stop bolts. It is not difficult to install the tire, coupled with the saw, it is necessary to remove all the protective covers, unscrew the fixing bolts on the third part of the length and put the headset. Then tightly pull all the nuts, twist the tensioner with a special lever.
How to understand that it’s time to sharpen the chain?
The severity of the cutting links of the chain of the chainships is determined by the type and size of the sawdust: the dull the chain, the less efficiency it is cut into wood and smaller than the sawdust at the output.
The acute chain bites into wood at light pressure.
Do not lean on the saw while working, this often leads to injuries due to the rebound of the saw or the rupture of the chain!
Be careful, small sawdust and wood dust clogs the gas station air filter, and the dumb chain creates an additional load on the cutting headset and saw engine.
What chains are we sharpening?
Any dull circuits for electro and chainsaws without external damage. 2. Chains with incorrect sharpening angles. 3. Chains with an overstated or underestimated height of the drain depth limiter.
The order of work
Before talking about how to pull the chain of the chainsaw, it is important to designate several simple rules. Firstly, maintenance must be carried out when the engine is turned off and without the risk of its random launch
Secondly, all work is carried out after cooling the tool. The fact is that the hot saw chain has a large length than cold. If you start a stretch, then there will be a risk of tightening and deformation of the tire after cooling.
Remember security! Put on protective gloves so as not to cut your hands with sharp links in the chain.
If the saw set is installed recently and has slight wear, it makes no sense to change the chain. It is enough to adjust its tension. What are the signs of insufficient tension? In the lower part of the tire, the circuit sags, in the upper. it shifts to the side. This leads to a skew during sawing, which means that it affects the service life of the tire. it wears out unevenly. In addition, insufficient tension of the chain increases the risk of its jumping from the tire and is the cause of increased wear of the saw blade and a drive star
Since it is correct to pull the chain of the chainsaw. does not mean just getting rid of its sagging, it is important not to pull it yet. The difficult course of the canvas in the tire helps to increase the load on the engine and other work nodes of the tool
Try to scroll the chain around the tire with your hand. If this succeeds, it needs to be loosened.
It’s important to know! Most often, the tension requires a new chain, since it has the ability to stretch at the beginning of operation. Constantly check its tension and, if necessary, adjust
So you extend its service life and reduce the wear of other important details of the saw.
To replace the saw canvas, you should release the tire and remove the old chain. To do this, weaken the fasteners of the lid, which holds the saw set, remove the chain from the asterisk and remove the equipment. The new chain should have the same sizes as the old. It is installed on the tire in the longitudinal groove by leading links. The free end of the chain is attached to the asterisk. Be sure to make sure that along the entire length of the headset the links entered the groove. Install the tire on the pin at the mounting site to the tool. Close this knot with a lid and fix the tire. For this, screws or a rotary regulator are used.
Tip: In order for the tire to wear out evenly, it is recommended to turn it over. change the upper and lower part. You can navigate by the inscription on the tire. For example, if the letters were located correctly, when replacing the inscription should be upside down.
The instructions for the tool should describe how to pull the chain of the chainsaw correctly. However, there is no way to use it. Therefore, we will talk about the sequence of actions when servicing saws with different types of chain tension.
Traditional chain tension using a tool. You will need a standard key, which is usually included in the setting set of a chainsaw. On the one hand, he has a working part to unscrew the nuts, and on the other. a slotted screwdriver. First you need to loosen the nuts on the lid, which closes the tire fastening place. Then insert the screwdriver into a special groove and rotate it to stretch the circuit. Do not be zealous. it is better to pull the chain gradually. Make several revolutions. to control the tension with your hands, pulling the chain in the lower part of the tire. After the adjustment is completed, you need to tighten the nuts on the lid.
Non.conductive tension of the chain. This method is simpler and faster. On the side of the cover there is a adjusting screw for tensioning the circuit. Rotating it, you control the decrease in the sagging of the chain.
How to understand that the chain of the chainsaw is stretched correctly? It should not sag from below, and when it is delayed, the internal teeth should exit the tire groove by no more than 4. 6 mm
It is important to make sure that the chain is not pulled. To do this, scroll it manually along the tire in the direction of rotation, as when sawing
If the move is light, then you did everything right. It is believed that it is better to almost reach the chain than to pull it. In the process of work, this will be quickly discovered and adjusted. But the difficult course of saw equipment is not immediately noticeable and has a pernicious effect on the engine. Performing the maintenance of the tool with your own hands, you will know how to stretch the chain of the chainsaw without the risk of damage to its working nodes. As soon as you achieve optimal tension, you can fix all the fasteners and turn on the tool. Let him work at idle, without load. Then drown out the engine and make sure that the chain has not flown and did not sag. Such a tool can start working.
Repair standards and restrictions
Recommendations for fixing the worn rivets with electric welding do not take into account changes in the structure of the metal from even short.term high.temperature effects of the welding arc.
Picked up by welding or warmed by an abrasive circle of corner grinders, the connecting elements of the chain are less wear.resistant, which significantly affects their reliability.
- The tight connection of neighboring links is accompanied by additional loads on the engine and kinematics of the chainsaw.
- The absence of a smooth chain progress makes it difficult to enter the headset into the cut, the possibility of reverse strikes and other traumatic points is not ruled out.
- “Tugged” and glued joints of the renovated chain are more susceptible to breakdown with a sharp load on the load.
The easiest in design, the machine for repairing chains of chainsaws justifies its value with the ability to completely replace the damaged chain for a short segment of working time and restore its performance at the level of up to 90%.
Chinese.made chains are essentially copies of European models, therefore, the above repair recommendations are valid for the entire Chinese chain assortment.
Shortening the chain with your own hands
You can shorten the chain of the chainsaw with your own hands using simple tools. This method is less reliable, but easy to use, does not require special skills in working with cloth equipment. Disadvantage. you cannot control the strength and quality of crushing rivets. This can lead to a breakdown of the tool with serious loads.
What tools will be needed for repair at home?
You can work with the help of the most affordable tools. Depending on the skills and skills, it may be required:
Some masters also use an electric welding machine. It is not recommended to use it, since the seams after welding quickly become unusable under the influence of vibration during intensive work of the chainsaw. This method is suitable only for gearbox chains that transmit efforts to the leading star.
Removing rivets
To disconnect the links, it is necessary to apply physical effort, since high.quality steel is used to manufacture the headset. Before starting work, the circuit is firmly fixed in a vice in order to avoid injuries during the removal. Stack the protruding part. Do.it.yourself rivets itself can be removed in the following ways:
- Continue to grind with emery until the jumper. Attach the beards, hide the metal with a hammer.
- Stream rivet corner grind. Disadvantage of the method. you can damage the chain itself. Work should be carried out carefully, periodically wetting the area with water.
- After squeezing the chain in the vice for the guides, cut the rivets with a chisel.
Read also: Scheme of the welding machine AC
If you need to increase the number of links or remove one of them, then you need to remove at least two rivets (left and right). When using a corner grinder, the metal can heat up, so after grinding you need to wait for cooling or work in protective gloves.
Connection of links
You can purchase a new link for any chainsaw model in any specialized store, remove it from the old headset. The use of donor spare parts is not recommended, since the quality of the cutting canvas is reduced from this. Installation technology:
- Install the link with new rivets on the chain. Put on the anvil with an open side up.
- Put the top plate on the rivets, stick a hammer for a tight connection several times.
- Attach the beards on the rivet, make 1-2 strong beats with a hammer. Achieve a pronounced thickening, flattening metal. Repeat the operation on both sides of the link.
After work, it should be checked that the chain is mobile, all its elements go freely in different directions. This avoids jamming during sawing.
Important! The headset cannot be installed on a chainsaw if the links cannot move freely. After repair or change in length, check each element.
How to dress and pull the chain correctly?
Before starting work, you should put on gloves to avoid cuts about sharp teeth. Only a cold chain can be pulled. after cooling, it can burst from overvoltage, damaging the mechanism. Remove the protective casing from the chainsaw, carefully put it on the tire.
Depending on the configuration of the tool model, the tension is given manually or using a special regulator. In the first case, you need to loosen the bolts on the tire, after installing the circuit, give the voltage using a slotted screwdriver. If there is an adjusting bolt, then turn it all the way until a sufficient tension of the canvas appears. After work, check the absence of sagging, be sure to tighten after the first operation.
Picking chain tension adjustment
A professional foller will never start working with a chainsaw until it checks the stretch of the chain. If it is weak, the headset will hang out when moving, jumping off the tire and may well burst. Excessive tension also does not promise anything good. the increased loads on the engine and the rapid wear of structural elements critically reduce the working resource of the tool.
In most models, a spar tint of the saw fixes the tire. This means that if it is insufficient or excessive, the tire will have an increased backlash, or its stars will be clamped and will not be able to move the headset.
The process of stretching the saw chain is performed according to the following algorithm:
To do this, approximately in the middle of the tire in its upper part, the chain is taken by the tooth and vertically pulled up. With optimal tension about a third of the shank will remain in the groove of the tire, and the chain itself rotates freely with the hand. If not, then it is pulled or weakened.
Before starting the repair, you must make sure that the chainsaw is turned off and its random start is completely excluded.
To do this, you need to turn the chain with your hand along the line of the working course. If the headset is weakened, in the lower part of the tire you will notice a sag.
This node is located inside the fixing cover of the cover, which is located near the brake coupling. You should release the fixer nuts and crank the tensioner (control bolt) until the normal quality of the tension is achieved while maintaining the smoothness of the chain and the necessary hinged backlash.
It is forbidden to change the chain or adjust it in a heated state. When cooling, the metal is compressed, so the set adjusted in this way can deform the tire or disable the engine.
Why Loggers Run Upside Down Chainsaw Bars
How the chain of chainsaw is lubricated?
It should be noted that during the operation of the chainsaw, the oil receives not only the tire, but also the tool chain. After the oil enters the tire, a saw element is included in the operation, the links of which are also equipped with grooves or holes. With an increase in the number of engine speeds, the speed of the oil and circuit increases and the speed of oil. Some models of modern chainsaws are equipped with special mechanisms that allow you to increase or decrease the amount of oil necessary for good operation of the chain. Lubrication of a chainsaw with such a function is quite convenient, as it allows you to save oil and eliminates slipping the chain on the tire from an excess of lubricants. Very often, beginners do not know how to lubricate the needle bearing of the chainsaw. This element requires lubrication no less than the tire and chain. Experts advise using special consistent lubricants from STIHL and Husqvarna manufacturers as a lubricant. To add lubrication, use a syringe so that the whole product gets inside the bearing. If we ignore the need to lubricate the needle bearing, then the result will be the replacement of the leading video and a number of other important parts of the chainsaw.
You can delete rivets without the use of specialized devices in several ways:
Rivet removal with a file
- Stiffen. When using this method, it is necessary to control the degree of pressing to the rivet in order to avoid damage to working parts.
- Cut off a cut circle of an angle grinding machine. It should be borne in this case that in this case the metal heats up, which will affect its properties.
- Cut the heads with a file or a file. With this method, the risk of damage to the links is minimized.
- Cut down using a chisel. Before starting work, you will need to reliably fix the chain in the vice.
After the external protrusions are completely cut off, you will need to knock out the rivet from the seat. To do this, you need to choose a punch, the diameter of which will correspond to the diameter of the hole. The punch must be put on a rivet and knit it with a sharp blow of the hammer. After these actions are performed, the chain will be disconnected.
Attention: In order to avoid damage to the links, you need to securely fix them. In addition, the punch should be installed strictly perpendicular to the cut of the rivet
Before and after rummaging the chain
Shortening the chain with your own hands
You can shorten the chain of the chainsaw with your own hands using simple tools. This method is less reliable, but easy to use, does not require special skills in working with cloth equipment. Disadvantage. you cannot control the strength and quality of crushing rivets. This can lead to a breakdown of the tool with serious loads.
What tools will be needed for repair at home?
You can work with the help of the most affordable tools. Depending on the skills and skills, it may be required:
Some masters also use an electric welding machine. It is not recommended to use it, since the seams after welding quickly become unusable under the influence of vibration during intensive work of the chainsaw. This method is suitable only for gearbox chains that transmit efforts to the leading star.
Removing rivets
To disconnect the links, it is necessary to apply physical effort, since high.quality steel is used to manufacture the headset. Before starting work, the circuit is firmly fixed in a vice in order to avoid injuries during the removal. Stack the protruding part. Do.it.yourself rivets itself can be removed in the following ways:
Continue to grind with emery until the jumper. Attach the beards, hide the metal with a hammer. Stream rivet corner grind. Disadvantage of the method. you can damage the chain itself
Work should be carried out carefully, periodically wetting the area with water. After squeezing the chain in the vice for the guides, cut the rivets with a chisel.
Read also: Scheme of the welding machine AC
If you need to increase the number of links or remove one of them, then you need to remove at least two rivets (left and right). When using a corner grinder, the metal can heat up, so after grinding you need to wait for cooling or work in protective gloves.
Connection of links
You can purchase a new link for any chainsaw model in any specialized store, remove it from the old headset. The use of donor spare parts is not recommended, since the quality of the cutting canvas is reduced from this. Installation technology:
- Install the link with new rivets on the chain. Put on the anvil with an open side up.
- Put the top plate on the rivets, stick a hammer for a tight connection several times.
- Attach the beards on the rivet, make 1-2 strong beats with a hammer. Achieve a pronounced thickening, flattening metal. Repeat the operation on both sides of the link.
After work, it should be checked that the chain is mobile, all its elements go freely in different directions. This avoids jamming during sawing.
How to dress and pull the chain correctly?
Before starting work, you should put on gloves to avoid cuts about sharp teeth. Only a cold chain can be pulled. after cooling, it can burst from overvoltage, damaging the mechanism
Remove the protective casing from the chainsaw, carefully put it on the tire
Depending on the configuration of the tool model, the tension is given manually or using a special regulator. In the first case, you need to loosen the bolts on the tire, after installing the circuit, give the voltage using a slotted screwdriver. If there is an adjusting bolt, then turn it all the way until a sufficient tension of the canvas appears. After work, check the absence of sagging, be sure to tighten after the first operation.
How to determine the degree of tension
Fast verification of the tension of the chain is carried out very simply: you need to take up the tooth and pull it up. If the chain is stretched correctly, then the tail will be immersed in the groove of the tires by 1/3 of its height. Excess of this indicator indicates excessive tension, and a decrease in the indicator. of a weak.
With a strong tension of the cutting element of the chainsaw, the tire begins to heat up and grind, the load on the engine rises, and it quickly wear out. It is forbidden to turn on the unit with a weakened chain, since when sawing it can be clamped and cut off, which is dangerous for the user of the unit. The chain can fly off the tire and injure the limbs, while it is often damaged itself and damages the tire. Also, working with a weakened chain element leads to a unilateral tire wear, after which the device stops making even cuts, and takes the saw aside.
How to make the right rivets with an electric drill?
Do not be afraid: no one offers to receive a machine for you. Use an ordinary drill. The whole process of rivets production using electric drill and everyday subfille describes in the subsequent way. From a nail, the diameter of which is equal to the dialect of the inside of the rivets (check with a caliper), a blank is cut out. a piece of about 7 cm long. how can you shorten a chain on a Chinese chainsaw.Little how to do it. This workpiece is fixed in the electric drill head. Since which is on a chain in order to replace an asterisk on a chainsaw. The drill itself should also be firmly fixed.
Two supra.films are fixed on a wooden beam, the distance between which will be equal to the width of the inside of the rivet. This may not be possible to do this, but you must achieve absolute accuracy. It remains only to organize a uniform supply of bar to the workpiece. We advise you to use a piece of boards, one end of which is fixed to the motionless part of the workbench using a wide door hinge, and on the second end of the board we fix the bar with supra.films.
We check the perpendicularity of the location of the files and the workpiece. and you can begin to work. Turn on the electric drill and smoothly lower the files. They will make grooves on the workpiece. It is not recommended to make rivets at one time, because it is not worth overheating of the metal, but to control the thickness of the workpiece on the protected part. A very narrow part of the rivet can also destroy you, therefore it is necessary to achieve the greatest accuracy. If you were able to do everything right, it remains only to cut off the rivet and use it to connect the links of the chain.
It is better to cut off the rivet manually, without using a corner grinder. How to shorten the chain on the chainsaw: tips and. Do not attend that when cutting metal at large revolutions of the tool, a significant increase in the temperature of the material will occur, which is not very necessary. The finished rivet will not yield to the factory product in quality, because the restored chain will last a long time. Bad moments when using homemade rivets will actually be excluded. The main thing is that when setting rivets, you do not forgot to align the side parts of the links (after all, they had to be straightened when separating the chain). Even the slight protrusion of these parts from the constructive norm will lead to early wear of the leading star.
It is recommended to immediately make several rivets described earlier by the method. The point here is not only to stock up on such necessary elements for the future (although this is also fundamentally). It is more important to choose the most suitable in size from the entire number of products: at least what deviation from the norm will make the chain vulnerable at large loads.
The introduction of restored chains is not recommended when working with dense wood rock rocks.
How to pull: installing the cutting element of the chainsaw
The main reasons for the sagging chain we dismantled. How to install a chain on a chainsaw is described above. Now you need to correctly pull the grades, and check if it is pulled.
The chain stretch
You can pull the chains in two ways: fast and frontal. It is best to stretch the front way.
If you carry out a front stretch, you need to unscrew the nuts that hold the tire and raise it over the edge. A special bolt that is on the right must be pulled by the grades until an acceptable stretch is obtained, and then raise the tire even higher and squeeze it.
If you use the fast stretch method, then you first need to raise the handle of the lamb nut and loosen it. Then tighten the chain tension screw to the stop clockwise. Then tighten the lamb nut and lower the handle again.
Checking the stretch
To check the stretch of the circuit, you need to turn off the brake system of the saw. Then manually draw grades along the tire, if he walks smoothly and does not sag, then everything is fine. If the chains walk very tight, then it needs to be a little weaken, because there is a risk of gap during operation.
How to eliminate the risks of acquiring a low.quality fake
When buying a proprietary chain on the market, the risks of acquiring Chinese chain falsifications are not excluded. The task of independent choice is complicated by the lack of a reliable way to distinguish a high.quality branded original from a fake, which is inferior to company products by a working resource by a manner.
With greater confidence, according to silver packaging, a bright orange logo and the presence of a wear indicator, Shtlevsky chains can be identified. Cheaper Chinese analogs are more modestly decorated, in gray boxes with a yellow trademark.
Without fears, you can buy pile chains full-fledged in quality and durability in company stores and licensed trading representatives of intermediary companies.
Work tools
To remove the link of the cutting element, it is necessary to initially flare up rivets. To carry out flashing work, tools such as a hammer, an anvil, thin beards, a vice and a corner grinder with an emery circle will be required. These devices, although it will not allow you to make manipulations reliably, but their application will allow you to perform the procedure on its own. To do work better, you will need to use a special type of punch.
It’s important to know! If, on duty, you often have to shorten the chains for a chainsaw or electric saw, it is recommended to purchase special tools that will facilitate the work, as well as speed up the process.
The tools that will help to facilitate and speed up the process of removing links from the cutting element include:
- Rubber for rivets. Specialized machine that allows you to quickly remove rivets. The simplest tool, whose work resembles a press. In the set to such tools there are components that allow you to accurately remove rivets.
- The machine is riveted. An engine with a gearbox is installed on such a tool. Such a tool allows you to rivet the links with a step of 0.325 and 0.404 inches. Buying specially such a machine for home use is not at all rational, since it is quite expensive.
Having collected tools and materials, you need to start work.
Shorten the chain on the chainsaw with our own hands
Other methods are known to remove rivets in order to ultimately shorten the chain. They are represented:
- Take advantage of the sandpaper with which the hat hatching. In this case, the process is controlled so that the neighboring link is not damaged.
- Take advantage of the corner grinder. You can also remove the rivet with a corner grinder, using an emery or abrasive circle.
- Apply a chisel and a hammer. To do this, the product should be squeezed in a vice for the guides, and then resort to the harassment of rivets.
After removing two neighboring hacks of rivets, you will need to disconnect the link. To do this, you need to arrange between the connecting plates of the link of the beards, after which with the help of a hammer to hit it with jerking movements. The plate should eventually fall out of rivets. After that, you can resort to separation and removal of the link, as well as riveting the chain.
Not many know how to stuck the chain of chainsaws, so special attention should be paid to this process. You can’t do without a connecting link for the connection, which can be purchased at any tool store.
It’s important to know! When buying a connecting link, you will need to take into account the type of its chain, as well as a step and profile.
Many use such links from unnecessary chains, but it is not recommended to implement this. The connecting link with a rumbling element needs to be put on a circuit, and then place on the anvil so that the open part looks upward. The upper plate is located on the rivet, after which it is slightly tapped with a hammer. As soon as the plate falls tightly, you can immediately resort to flattening the equipment. To do this, a sharp effect is carried out with a hammer, placing beards or core on a rivet. A similar way is a riveting of the second rivet. The presence of a thickening of the protruding part will indicate that the procedure has been qualitatively carried out and reliability is ensured.
At the end of the work, you will need to check the movement of the connected links in the circuit. First you need to adjust the tension, and then resort to the test during the working motor. Such simple actions allow you to extend the service life of stretched or torn chains. In addition, the old chains can be installed on a shortened tire, having previously adjusted the cutting product to the corresponding length.