Trimmer for grass Benzotrimmer does not start what to do. Dry and wet candle what it is…

The causes of breakdowns of gasoline and electric trimmers

Trammer for grass, both electric and with an internal combustion engine (ICE), is an indispensable tool in the summer and autumn period for owners of cottages and private houses. With its help, weeds, small shrubs are easily removed and the lawn is trimmed. But, like any technique, trimmers for grass fail at the most inopportune moment. To eliminate the malfunctions with your own hands, the user of this technique first needs to determine the reason for their appearance.

In the lawn mower and an electric trimmer for grass, if you do not consider breakdowns associated with the bar and the mowing head, the malfunctions mainly happen in the engine area.

Damage of gasoline trimmers

Typical breakdowns of a gasoline trimmer for grass, which are most often faced with the owners of this unit, are as follows:

• engine breakdown;
• problems with the carburetor;
• problems with the supply of fuel;
• muffler malfunction;
• gearal breakdown;
• The starter broke;
• Air filter problems;
• Broken a buckshot on a gas tank.

Malfunctions of electric trimmers

Since the device of an electric coser is much easier than a motirmer, then there are few reasons for its failure.

It should be noted that the elimination of some of them is best entrusted to the specialist.

Basically, the trimmer for the grass ceases to work normally in the following cases:

• Electric cable malfunction;
• The control button is faulty;
• burned engine winding;
• Contact joints break on the engine.

Why is the gasoline trimmer not starting for the grass

The reasons why the gasoline trimmer for the grass stopped starting is different, therefore, a phased diagnosis of the apparatus is required.

Fuel tank (fuel quality)

Remember that always before starting the unit, a check of the presence and quality of fuel is required. In this case, you should not be greedy and save, as well as “clever” about the amount of oil added. Everything must be done according to the management attached to the apparatus, since when the piston group fails, its replacement will cost about 70% of the total cost of the trimmer for the grass. Pour fuel due to the fact that you will fully conside it when performing work. After a while, the gasoline remaining in the tank loses its properties and can harm the engine. Therefore, do not prepare the mixture for the future and in large quantities. If the lawn mower starts poorly, try to drain the “old” fuel from the tank, and season it with a freshly prepared mixture.

Important! To refuel the device with fuel, the origin of which is unknown, fraught with negative consequences. Gasoline should be of high quality, bought at a gas station, and its brand should be not lower than AI-95.

Candle and candle channel

So, you changed the fuel, but nothing has changed, and the trimmer for the grass still does not start. In this case, it is worth checking the candle channel: whether it throws it with a combustible mixture. Often users transfer the air damper to the “OFF” position when starting, and when the engine started, they do not transfer it to the “ON” position, after which it stalls. Further, an attempt to start the internal combustion engine to again leads to the fact that it floods the candle with gasoline, and the start becomes impossible. To diagnose and eliminate the possible problem in this node, do the following.

• It is necessary to unscrew the spark plug, wipe it well and dry it. When installing a candle in the ICE cylinder, it should be dry.
• Draw from the combustion chamber the fuel accumulated there. This is done through the hole from which you twisted the candle.
• In the presence of soot on the electrodes of the candle, it must be removed either with a thin file or a nail file.
• Do not forget to put the gap between its electrodes before installing the parts in place. The gap on the candle should be 1 mm. As a probe to check the gap, you can use a coin.
• Next, collect the block, read the start instructions and try to start the engine again.

If the engine does not start, then you will need to check the spark. For this:

• unscrew the candle;
• put on it a cap of a high.voltage wire;
• Touch its metal part to the cylinder body (to provide contact, you can insert a tubular key) as shown in the figure below;
• pull the launch cord so that several engine speeds occur.

Normally, with each piston roll between the electrodes, the candle should slip a spark. If there is a spark, then the reason that the internal combustion engine is not launched should be sought in other nodes of the device.

For a better understanding of the process, how to test the candle for the presence of a spark, you can use this video where the check is shown by the example of the Lawn Mushiel “Soyuz”.

If there is no spark, then in the beginning check the cable connecting the candle to the coil. perhaps the reason is in it. You can call it with a tester. In case of detection of the rupture of the chain, a high.voltage wire will require a replacement.

Also the reason that the spark has disappeared is a malfunction of the ignition coil (magneto). The figure below shows what the coil (magneto) looks like from the gasoline trimmer for Patriot grass (Patriot).

To exclude the malfunction, it will be necessary to use a tester to check the Magneto trimmer for the grass, namely, its primary and secondary winding. On the primary winding, the resistance should be in the range from 0.4 to 2.0 Ohms. If the device shows 0. this means that there is a short circuit in the winding, and if infinity is a clear sign of a chain break. The resistance on the secondary winding should be in the range from 6 to 8 kOhm.

On some coils, it can reach the value of 15 kOhm.

Air filter

If your lawn mower does not start well or stalls immediately after starting, you should pay attention to the air filter, since it can be clogged, as a result of which the air does not enter the combustion chamber, and fuel ignition does not occur. To check if the filter is the case, remove it and try to start the engine. If he earned, then the reason was found. The filter needs to be replaced or rinse well and dry before installation. In the case when you find the oil in an air filter, it must be washed with gasoline, squeezed well and dry at least 2 hours before installing in place.

If the unit does not start with an air filter, it is still recommended to check the fuel filter.

Fuel filter

This filter cleans fuel of possible pollution. If it is scored, then gasoline does not enter the cylinder, and, accordingly, the unit does not work or stalls after starting. The fuel filter is located at the end of the fence hose, which is located inside the fuel tank. To get to the filter, it is necessary to extract a cork with tubes emerging from it.

When extracting traffic jams, a fence hose can disconnect and stay in a tank. It is extracted with a tweezer.

Next, remove the old fuel filter from the hose and put on it a new, pre.acquired. You can also clean the fuel filter if you do not have new. The filter must be fixed on the hose using a spring latch.

Install the fence tube on the cork and insert the last into the tank.

Redverg Basic GB52C gasoline trimmer

The Redverg Basic GB52C gasoline trimmer is designed for domestic use. Ergonomic bicycle handle with cast mount provides comfortable work with the tool. A coil with a fishing line is used to mow grass, and a 3-bladed disk 255×25.4 is used to spit up thickets.

Trimmer for grass Redverz Redverg RD-GB252 is powerful and reliable, it will cope with both dense thickets of hard grass and small shrubs. This tool will provide you with comfort and safety when working. A convenient bicycle handle will give the operator the opportunity not to get tired even during the most voluminous tasks. The system of shoulder straps will evenly distribute the weight of the equipment and practically do not pay attention to the tool. Redverg gasoline trimmer combines high technical characteristics and affordable price.

Redverg Redverg RD-GB243S GARS

Trimmer for grass gasoline Redverg RD-GB243S is designed to work with grass and small shrubs. With it, the operator will be able to quickly and easily put the lawn of small or medium area in order. Comfort and safety during work. this is what the manufacturer first turned to. The ergonomic bicycle handle gives the master the opportunity to sensitively control the direction of movement of technology and achieve impressive results of any work.

Rating of powerful motoblocks for working on your site

Chain chain tips

What to do if a gasoline lawn mower is faulty?

Learn about profitable offers and receive personal recommendations

The goods are presented on the site by photographic materials, photographs, text, schematic, and advertising materials. are the property of the seller. At the request of the buyer, the seller may provide detailed information on the products provided for the product.

Information posted on this site is not a public offer provided for.2 of Article 437 of the Civil Code, and is also possible by any other norms of civil law or a foreign state. This information does not express the will of the subject who posted information about the product for the conclusion of any relationship, both a certain circle of persons and an indefinite circle of persons. The information presented on this site is only information about the achievements in the production (or wholesale-trade) sphere that the owner of the site was able to achieve. Information provided on this site cannot be used to conclude, execute and terminate the contract of sale concluded by remote method.

Why and what to do if a gasoline trimmer for grass does not start

If a benzotrimmer does not start, the breakdown can be caused by several reasons. Most often, the failure occurs:

• due to clogging of air or fuel filters;
• because of the exhausted old gasoline in the tank;
• due to damage to the fuel hoses;
• due to damage to the ignition system;
• due to a short circuit of the wires responsible for inclusion.

Also, the launch of the primer and the saapon, the clogging of the carburetor and the air damper drive clogged.

The most difficult thing is to repair a benzotrimer with a malfunction of the engine, but such a breakdown is rare

Exhausted gasoline in the tank

Many trimmers left fuel in the tank after using the unit. If the cover is not closed not, gasoline can exhale and absorb moisture from the air. As a result, the combination of the mixture is reduced, and the motor does not start.

It is very simple to fix the situation. you need to remove old fuel from a gasoline trimmer for grass. Do it like this:

• Pump up new gasoline primer.
• Twist the starter cable many times.
• Pump the old fuel through the combustion chamber until the tank is empty.
• Dry the candle.

You can also simply remove and disassemble the carburetor to drain the remnants of exhausted gasoline. But it is more difficult to do this, you must have minimal ideas about the device of a trimmer for grass that does not start.

A short circuit of wires

The wires suitable for the engine are responsible for the engine. they are connected by the switch, and as a result, the gasoline trimmer for the grass is launched. Due to poor-quality isolation or permanent vibrations, the cables can be wiped out.

If a short circuit occurs, the engine is not started by pressing the button. You can eliminate the problem according to this scheme:

• The wire departing from the start button is removed from the terminal terminal of the ignition system.
• Using the tester, check the cable resistance in “Inclusive” and “off” modes.
• If there is a malfunction, a working handle of a gasoline trimmer for grass is disassembled.
• Cut or solder suitable to the motor, ignition system and wire button.
• Extract the remains of cables and set new in their place.
• Collect the hilt back.

If the gasoline trimmer for the grass starts again, the repair was successful.

Attention! In good wiring during testing in “inclusive” mode should give resistance striving for infinity.

Flowing the air filter

If the trimmer for the grass has not stalled and does not start, the problem may consist in clogging an air filter. To diagnose a breakdown, you need to extract a candle from the unit case and inspect it. If there is clogging, it will be black.

To eliminate the problem, you need to disassemble the motorcycle and pull out the filter from the body. It is cleaned in accordance with the instructions for a specific trimmer for grass, and then set to place. To prevent the problem, it is recommended to conduct preventive maintenance of equipment from time to time.

Falf in the spark plug

If the benzotrimer does not start, the failure can be caused by a candle breakdown. Diagnosis is carried out as follows:

• Twist the element from the cylinder block head.
• Carefully examine. if the contacts of the candle will be covered with a malfunction, will be covered with a black coating.
• Soak the part in vinegar solution 20% for half an hour to clean.
• Sprinkled with soda and washed with water after another 30 minutes.
• Dry with compressed air and installed in place.

In some cases, after cleaning, the candle comes into an efficient state, and the gasoline trimmer for the grass starts again. If this does not happen, you need to replace the element with a new.

If a black fog quickly appears on the new candle, the problem may consist in re.enriched fuel

The ignition coil malfunction

If the trimmer for the grass is jerking off and does not start, it is worth checking the ignition coil. Do this as follows:

• All wires turn off the block and remove them from the candle.
• Measure the resistance of both coils-in the primary it should be 2-3 Ohms, in the secondary 4.5-5.5 ohms.
• With a strong deviation of the indicators, the ignition unit is replaced with a new.

You can check the knot in another way. Instead of a candle, the tip of the discharge is inserted into the appropriate wire and the latter is connected to the motor. Then you need to set a gap with a size of 0.5-0.8 mm and twitch the starter cable. The ignition unit requires replacement in the absence of a spark, but if it is, then the malfunction lies in the candle.

Recommendations and preventive measures

It is quite difficult to start a benzotrimer with malfunctions, sometimes repair requires a lot of costs and applies of efforts. Avoid breakdowns allows compliance with prevention rules. In particular, it is recommended:

• Timely clean the ribs of the starter and channels on the housing of a gasoline trimmer for the grass;
• Before a break in the operation of the unit, drain the remaining fuel from it;
• After cleaning the gas tank, start the engine at idle to eliminate the last traces of the mixture;
• use only high.quality fuel when operating the unit;
• load a gasoline braid in accordance with the instructions;
• Before cleaning for storage, disassemble and thoroughly rinse the trimmer for grass with solvents.

It is recommended from time to time to subject the gasoline braid to be careful to identify mechanical defects. Regular preventive cleaning requires air and fuel filters of the system.

Attention! Before cleaning the gasoline trimmer for storage grass, you need to lubricate the piston group with motor oil.

The more intensively the benzotrimmer is used, the more often its individual working nodes clog

The lawn mower will not start. what to do?

It is not the first you to carry out lawn work using a gasoline braid or a trimmer for grass. Already by inertia you perform the entire algorithm for turning on the unit and suddenly understand that it will not start. How to be?

In distant times, even before the start of urbanization, in rural areas, simple devices were used specifically to combat high grass and weeds, one of which was an ordinary manual braid for grass. Everything was clear with her: he broke a blade or a bracket. replaced the instrument with an analogue and work further. But one day everything has changed.

Progress did not stand still, and one fine day to replace the good old mechanical spit with the aim of facilitating the village (and over time. and country) work came improved mechanisms. a gasoline braid for grass and a trimmer for grass. Getting rid of unnecessary grass with their help has become much easier, but another problem arose. Once a miracle gadget may suddenly take and not get started. For what reasons this happens, and what needs to be done in such a situation?

Inspect the spark plugs. One of the most frequent problems with a gasoline scythe or trimmer is due to the fact that due to excessive pumping of the fuel, the spark plugs were flooded. First of all, they need to be extracted from the mechanism and inspect. If a fiber has formed on a candle, clean it and dry it. Then return to the place and try to start the unit again.

Check the fuel. If you purchased a lawn mower or a trimmer for grass not so long ago and tucked it with gasoline of such a variety that is not suitable for it, then the unit is unlikely to start. Carefully study the instructions and, if necessary, read on the Internet all the necessary information on this topic. The same story with butter: if it is old, then perhaps the second component of the fuel is not to blame for anything. The third option is that there is little fuel in the tank, and this volume is not enough for the normal operation of a lawn mower or a trimmer for grass. Try to update the fuel, strictly observing the proportion indicated in the instructions when mixing gasoline and oil.

Inspect the fuel line. If a braid for grass leaves a wet trace, and air also enters the carburetor along with the fuel, as a result of which there is no traction, most likely, the cause of the malfunction is in this part of the mechanism. For example, the fuel line hose cracked. In this case, it must be replaced without fail.

Replacing the fuel pipeline of a trimmer for grass with your own hands

Remove and clean the air filter. Perhaps the work of gasoline braids for grass or trimmer for grass interfere with dirt and remnants of grass that have scored this part of the unit. As soon as you get rid of pollution, return the filter to its place and try to start the mechanism again. For an additional check, you can do this without an air filter. If the lawn mower does not start, the reason is not in its clogging.

Among the more serious reasons why a gasoline braid for grass or a trimmer for grass may not be started, experienced summer residents call problems with the ignition coil and engine. In this case, the mechanism should be taken to the service center or return under warranty. This, of course, is unpleasant, but if the lawn work needs to be carried out urgently, then you can lend the same unit for the neighbors or, in the end, find the good old manual braid in the attic.

Do you use a benzoca or a trimmer, and have you had to deal with problems in their work?

To send a comment you need to log in.

Everything is like my Hammerflex MTK 31. He started, began to mow, after pumping a plot of 105 meters, a braid for herbs died out. Attempts to start a nickname did not bring anything, cleared the candle, started. Literally a minute later, the braid for the grass was stalled and no longer wound up, even the starter could not pull, it closes in half, it is impossible to pull the cord.

Check the high.voltage wire and tip on the candle. I have a spit for grass “Patriot” (3 liters.With.) turned out to be a tip. just a piece of paper clip (the wire inserted into the wire). I took VP from the old Volga. everything works amazingly.

The braid for the grass did not start, changed a new candle.There is no spark, what to do?

It is necessary to check if there is a spark when leaning the cradle (cap of candle) to the cylinder. If not, call the high.voltage wire for its integrity. If the wire is intact. see the ignition unit.

After winter I tried to start the braid S K.240, and the starter does not twitch. Last time worked normally. Spit year.

Most likely the carburetor settings were lost

Wife flooded in Hammerflex pure gasoline.The trimmer for the grass works for 5 minutes and stalls Then I told her to urgently merge it and diluted it They did everything as it should, but still stalls after 5 minutes until the clean gasoline for the grass did not flush

LEX mower starts up normally, but for some reason it is quickly warming up and does not start on hot, tell me what the problem is?

“Forester 304”. It doesn’t start in any way, last year it was brought up with a kick from the same time, and then I worked a little and jammed, this year it didn’t start at all, they checked the candle, the candle is dry, the thread is slightly wet, the candles were changed, but the candle is, they changed gasoline. did not help, tell me what to do

Hello! I have such a problem, I started a braid, gave gas, it is strangled, I went clear a carburetor for a compressor, but I decided to buy a new one, put a new one, it no longer starts on any carburetor, the candle fits the spark, but for some reason the air filter in Half gasoline was not there before, and no one touched the carburetor, both new and old. What to do?

I bought a new lawn mower Occurrest 4200. The engine does not start. What to do?On the service were able to run for a minute. Compression 8ATM. What could be the reason?

The braid for the grass does not start the proton MI 2500: it was a little smashed, drowned, then started again, it stalled and did not start anymore. I cleaned the candle from the haze, but it did not help, the candle constantly floods

Another reason for not starting the lawn mower may be a silencer, I, on the advice of his familiar mileage (such a snake Gorynych turned out) and a braid for the grass started!

Do not start a lawn mower. Gasoline is not supplied at all. If you wet the candle, it will hole it once and that’s it. The carburetor was washed in gasoline, blowing. Uselessly.

See if fuel is supplied to the carburetor from the tank.

And how complete your tank is? If under the neck, then fuel is not supplied so will not be created in the tank. The reason can also be a torn membrane in a carburetor. In this case, you are in the service center.

Half a bacon. I tried even with an open lid. The membrane is not torn, it can be stretched In general, I will better take it to the service center. So as not to deliver her fuck

The PROMO RVS-43 trimmer does not start and the candle is dry, and gasoline enters the carburetor.Please tell me what the reason can be ? Thanks !

Help! The mower starts up but does not gain momentum

Good afternoon floods the candle drying it, it starts to get a knife on the gas stalls a trimmer for the grass new champion tell me what are the problems

In the trimmer Shtil FS 55, after replacing the ignition coil, oil seals and piston rings, does not start.What could be the reason

TEXAS trimer, there is a new piston, gasoline acts, it worked as a staller cooled a candle, I got a stupid changed the zero, you try to grab a dry candle, but it can’t get wet, as soon as the candle is weeping all sparks, that you advise you, that you advise.

After warming up the engine loses power and revolutions, what and what to do?

The lawn mower starts on the leak and when you turn off the leggbaking braid for grass stalls) help

Most likely problems with the carburetor. Engine defect needs.

Hello, a Chinese lawn mower is not started. Replaced the carburetor, piston, magneto. There is no effect. On the old piston were bulletin. What could be the reason.

The Carver GBC 31FS lawn mower is not started, and if you started, it does not work at low speeds (idle).What to do?

Good afternoon. The lawn mower recently began to start for a very long time when the accelerator is turned on, you need to pull the cord for a very long time, after which everything starts and works well, starting hot from the second third time, but during operation it splates the entire body of the motor felts, felts with working out or gasoline, I do not understand, help advice.

A motorcycle braid for Iron Angel BC 25 is not started that could be? Carbon new was working in a couple of days I did not want to start up

Problems with the carburetor, and the engine is necessary to defect. I read what you write?

Hello. The Stihl FS-55 lawn mower, the spit is 2 years old, but rarely used, the total operating time is no more than 5 hours (I think that less-the site is not large-I roll out in 15 minutes). Last year I worked strained, I had to gnaw so that I would not stall. This year, the plant does not respond to the plant at all. The candle is working-rearranged at the MS-180 saw, and a candle from saw to a braid. I also tried to fill the gasoline directly into the cylinder and start. the braid for the grass starts and stalls. T.e. Gasoline does not act. When you press the primer, the fuel enters it. Crossed the carburetor. it is virgin clean. Pulled out and wiped all the gaskets, filter. I blowed holes. When trying to unscrew the jacket. a little broke (broke) on a slot, but the nozzle itself is normal. He also blew him. In short, he killed all day on a thorough bulkhead (and more than once sorted out), but nothing helped. a braid for grass does not start. I also tried to regulate the carburetor. with the same result. What else can be done? In my opinion, it remains to only disassemble the braid for spare parts, and carefully examine each node. But somehow I really do not want to go there, despite the fact that the braid for the grass is almost zero, despite age.

Elimination of the reasons why the lawn mower is not started

The fuel mixture should be prepared with accurate observance of gasoline and oil proportions. In this case, you cannot use another brand of fuel. To exclude dirt, gasoline should stand in a glass or metal dish 2 days. Cannot be used for storage of fuel plastic dishes. Distribute the oil with a medical syringe without a needle. Use only a freshly prepared mixture, without leaving an unexplored fuel in a tank. If the engine is capricious, the lawn mower stalls, when you press gas, it may be guilty of fuel.

The lawn mower does not start hot. press the gas trigger and pull the cord abruptly several times until the engine earns, then lower the trigger. Not starting. specialized repair is required.

Checking the ignition system, if the lawn mower is not started, is carried out sequentially:

• Clean the removed candle from soot and dirt, dry, set a gap of 1 mm;
• Connect to a high.voltage wire and check on a spark, twitching a few times;
• In the absence of a spark, check the high.voltage wire for integrity;
• replace the candle;
• dry the candle channel;
• At the same time, the operation of the ignition coil is checked, it is faulty if the working candle does not spark.

It is in the case of a malfunction of the ignition coil that the lawn mower does not start hot, stalls, works with interruptions.

Cleaning or replacing the air and fuel filter will provide the necessary consumption of ingredients entering the carburetor. Air filter can be washed in soapy water or replaced. If the nylon canvas is used, it is washed, the porous felt filler is replaced. The fuel filter is changed neatly, not leaving an open suction pipe. Whether the replacement of the air filter is needed, it is possible to determine if the engine with the air purifier removed is launched. Whether it is necessary to change the grid on the fuel supply, if the lawn mower is not started, a dry candle will tell.

Sapun, a hole for air intake into a gas tank. If it is clogged, discharge is created in the tank and the mixture does not enter the carburetor. The hole can be blown with air or cleaned with a needle. Clean the exhaust channel, remove the anti.icper mesh of the muffler.

Carburetor adjustment and configuration

The maximum and minimum engine speeds, even idle is regulated by the carburetor. The stable operation of the lawn mower depends on the amount of fuel mixture and air. The lawn mower is not started with disturbed adjustment of the carburetor. The procedure for setting up the device for supplying fuel at low speeds (L), high speeds (H) and idle (T) is regulated by the same vints:

• The chainsaw should work for at least 10 minutes, since the adjustment is carried out in hot.
• The screw n is flooded smoothly to maximum speed, then turning on ¼, counterclockwise, reducing the speed of rotation of the engine shaft.
• The idle stroke is regulated by the screw T, ensuring that the braid for the grass does not rotate.
• The screw l is regulated, first opening the throttle as much as possible, and then smoothly reducing the speed to stable minimum.

After adjustment, a proper carburetor with cleaned filters should ensure the operation of the engine. In the event of a malfunction of the carburetor, after its repair, it will again need to configure the supply system before starting the lawn mower.

Rare breakdowns that prevent the operation of the lawn mower can be:

The most important malfunction, the elimination of which is associated with the replacement of the engine may be the failure of the piston group of the engine. The cost of repair will cost about 70% of the cost of the product. To figure out the reasons why the lawn mower is not starting up will help

Why is a trimmer not starting for grass (gasoline)?

Why is a trimmer not starting for grass (gasoline)?

Because he worked his. Why, this question may be as many answers. Poor fuel is far from an argument. Maybe a person does not know how to use it, so it starts not correctly. The fuel does not come, the candle is pierced, the wires are pierced, it does not turn on, does not know how to use it, the trimmer for the grass burned/broken, but there are still any other reasons can be. There are still such hooks.

The reasons why the gasoline trimmer for grass does not start can be several.

If the trimmer for the grass does not start or immediately stalls after the launch, then the problem may be in the fuel tank (namely as fuel), in the candle and the ultimate channel, in the air or fuel filter, in the saapon or the exhaust channel.

one). Be sure to check for the grass before starting a trimmer for grass, and most importantly and the quality of the fuel mixture.

2). A trimmer for grass may not start or stall with a flooded candle. It will need to be twisted and wiped.

Dry the channel candle for at least 3040 minutes. Otherwise, a new candle can also burst.

3). If a trimmer for grass starts without an air filter, then it is better to change the old filter for a new.

four). A trimmer for grass may not be started if the fuel filter is polluted.

5). Also, a trimmer for grass may be started due.

Also, the reason may be in the flow of dirt into the exhaust channel or clogging the muffle grid.

A gasoline trimmer for grass may stop starting for several reasons at the same time.

Firstly: try to clean the carburetor-its pollution leads to a breakdown of a gas station.

Secondly: vacuum may form in the barrel. If so, try to make a small click in the barrel lid.

Thirdly: roll the correct settings of the trimmer for the grass.

There are several reasons, as a result of which the trimmer for the grass will not start. I will list the main:

• Poor fuel. For each model of a trimmer for grass you need gasoline with a specific octane number. Roll up with the operating instructions and make sure that you fill in the required.
• flooded candles. At the same time, I advise you to check the candles for performance. Sometimes even new (in the box) candles can be inoperative or defective.
• The fuel mixture does not enter the carburetor. Skip it a little.
• The ignition coil failed.
• The muffler is clogged. You need to free it from the haze. To do this, carefully disassemble and clean (can be burned on a gas burner).

Typically, the trimmer for the grass did not start after winter and we used to carry almost every spring a trimmer for grass to the workshop, where we were repaired. But, once, a knowledgeable person advised us in.the first, never leave gasoline in trimmer for the winter, because old gasoline may be the reason that the trimmer for the grass will not start, and he also said that the trimmer for the grass for the grass is necessary for the carburetor.fuel mixture. After we began to comply with these rules, our problems with the trimmer disappeared.

First of all, you can see the candle. If necessary, replace it, making sure that the candle is not broken and gives a normal spark. The next problem will be hidden in the fuel system. As mentioned above, check the tightness, then check the fuel filter, if necessary, change. Clean the carburetor, watch the effect. It will be necessary to delve into the ignition system, configure. To check the fuel system, you can pour several grams directly into the cylinder through the candles of the candle, screw the candle and try to start. At least a trimmer for the grass should make the sounds of a running engine within 1-2 seconds and a little smoke should fly out of the silencer.

If you do not start a trimmer for grass at all or immediately stalls after the start of the start, then you first need to look for the reason in the main nodes and units, for this you need to carry out the test in the following sequence, so this sequence: this sequence: this sequence: this sequence:

In these nodes, the whole problem may be consistent.

What to do if the engine does not start?

If the lawn mower fails is not possible, then the first thing is to check the presence of fuel in the tank and its quality. For refueling the tool, it is recommended to use high-quality gasoline purchased at gas stations, the brand of which should not be lower than the AI-92. Savings on cheap fuel can lead to a breakdown of the cylinder-piston group, for the repair of which a third of the cost of Motokosa itself can take

It is equally important and correctly preparing a fuel mixture of gasoline and oil. The proportional ratio of these components of the mixture is indicated by the manufacturer in the manual

Do not prepare the fuel mixture in large volumes, since during long storage its properties are lost. It is better to use a freshly prepared mixture.

When preparing the fuel mixture, pour the oil into gasoline using a medical syringe that allows you to accurately comply with the necessary proportion of the components

Fuel filter pollution in the tank may also prevent the operation of the lawn mower engine. Therefore, when problems with the launch of the motor, check the condition of the filter. If necessary, replace the filter. It is forbidden to leave the incoming pipe without a fuel filter.

The air filter also needs to be in the test. During contamination, the part is removed, in the field is washed in gasoline and put in place. In the country or at home, the filter can be washed in water using detergents. After that, the filter rinses, squeezes and dries. The dried filter is moistened with a small amount of oil used to prepare the fuel mixture. Excess oils are removed by compressing the filter with hands. Then the part is installed in place. The removed cover is placed back and fixed with screws.

The air filter washed in the fuel mixture, squeezed and dried, is installed in place in the plastic case and covered with a lid

How this procedure is done in more detail you can look at

If all of the above procedures are carried out, and the engine is not started, then adjust its revolutions at idle, twisting the carburetor screw

In the video posted at the beginning of the article, attention is paid to this issue

• Put the tool on the side so that the air filter is at the top. With this location of the chainsaw, the fuel mixture is ensured exactly into the bottom of the carburetor. On the first attempt, the engine will start if you remove the air filter before starting and pour a few drops of the mixture into the carburetor, and then install the dismantled parts to the place. The method is tested in practice.
• If the first advice does not give a result, then, most likely, the problem in the spark plug. In this case, unscrew the candle and check its performance, as well as dry the combustion chamber. A candle that does not show signs of life, replace the new.
• If the spark plug is in good condition, the filters are clean and fuel mixture, then you can use the universal way of starting the engine. Close the carburetor air damper and pull the starter handle once. Then open the damper and pull the starter 2-3 times. Repeat the procedure from three to five times. The engine will surely start.

Some pull the pen with such force that it is necessary to repair the starter of the lawn mowed with their own hands. This is possible only in the case of a gust of a cable or breakdown of the cable handle. In other cases, it is recommended to replace the starter. This node is sold in the collection.

The lawn mower is not started? Eliminate the most common reason

Chinese motorcycles headache for the owner, but still without them nowhere. The main problem is the difficulty of starting after a long downtime. If the lawn mower worked as a clock in the fall, but it does not start in the spring, then you must most likely disassemble the carburetor and clean its valve.

Necessary tools:

If the motor motorcycles refuses to start, then first of all you need to check the candle. If it is completely dry, then this means that the fuel is not supplied to the combustion chamber and the reason is in the carburetor. Immediately it is worth checking the candle and for the subject of a spark in order to exclude it from the reasons on all fronts.

You can also make sure that the motor itself is serviceable. To do this, having twisted the candle, you need to pour a syringe into a combustion chamber of several milliliters of gasoline. After this, the candle is twisted and the lawn mower is started. If everything is in order with the motor, then it will work for a few seconds. This will once again confirm that it makes sense to disassemble the carburetor.

Next, a plastic protective cover is removed along with an air filter. After that, 2 screws are twisted with a cross.shaped screwdriver, holding the air damper and the carburetor on the engine. Fuel tubes immediately break down.

From the side of the cap of the suction, you need to twist 4 screws with a screwdriver, and divide it into 2 halves. We are interested in half with suction. There is a valve from its inside in the center.

He often sticks out, because after evaporation of gasoline, with a simple on it, a viscous oil works as glue. To check it, you need to put a short thin tube and try to blow the air through it. If he is stuck, he will not be able to blow out in any direction.

Caliping of the valve is eliminated by a conventional match. Toothpicks are better not to use, since they are sharp and can harm. A match must be slightly rested on the valve and stir it. After cleaning the match, it will be blown up.

Fuel will be able to act, so it will work. Cleaning the valve is not a panacea for all motorcycles that do not start after downtime, but this helps in 8 cases out of 10. The remaining 20%, as a rule, are also associated with a carburetor, usually with a needle.

Why is a trimmer not starting for grass (gasoline)?

Why is a trimmer not starting for grass (gasoline)?

Because he worked his. Why, this question may be as many answers. Poor fuel is far from an argument. Maybe a person does not know how to use it, so it starts not correctly. The fuel does not come, the candle is pierced, the wires are pierced, it does not turn on, does not know how to use it, the trimmer for the grass burned/broken, but there are still any other reasons can be. There are still such hooks.

The reasons why the gasoline trimmer for grass does not start can be several.

If the trimmer for the grass does not start or immediately stalls after the launch, then the problem may be in the fuel tank (namely as fuel), in the candle and the ultimate channel, in the air or fuel filter, in the saapon or the exhaust channel.

one). Be sure to check for the grass before starting a trimmer for grass, and most importantly and the quality of the fuel mixture.

2). A trimmer for grass may not start or stall with a flooded candle. It will need to be twisted and wiped.

Dry the channel candle for at least 3040 minutes. Otherwise, a new candle can also burst.

3). If a trimmer for grass starts without an air filter, then it is better to change the old filter for a new.

four). A trimmer for grass may not be started if the fuel filter is polluted.

5). Also, a trimmer for grass may be started due.

Also, the reason may be in the flow of dirt into the exhaust channel or clogging the muffle grid.

A gasoline trimmer for grass may stop starting for several reasons at the same time.

Firstly: try to clean the carburetor-its pollution leads to a breakdown of a gas station.

Secondly: vacuum may form in the barrel. If so, try to make a small click in the barrel lid.

Thirdly: roll the correct settings of the trimmer for the grass.

There are several reasons, as a result of which the trimmer for the grass will not start. I will list the main:

• Poor fuel. For each model of a trimmer for grass you need gasoline with a specific octane number. Roll up with the operating instructions and make sure that you fill in the required.
• flooded candles. At the same time, I advise you to check the candles for performance. Sometimes even new (in the box) candles can be inoperative or defective.
• The fuel mixture does not enter the carburetor. Skip it a little.
• The ignition coil failed.
• The muffler is clogged. You need to free it from the haze. To do this, carefully disassemble and clean (can be burned on a gas burner).

Typically, the trimmer for the grass did not start after winter and we used to carry almost every spring a trimmer for grass to the workshop, where we were repaired. But, once, a knowledgeable person advised us in.the first, never leave gasoline in trimmer for the winter, because old gasoline may be the reason that the trimmer for the grass will not start, and he also said that the trimmer for the grass for the grass is necessary for the carburetor.fuel mixture. After we began to comply with these rules, our problems with the trimmer disappeared.

First of all, you can see the candle. If necessary, replace it, making sure that the candle is not broken and gives a normal spark. The next problem will be hidden in the fuel system. As mentioned above, check the tightness, then check the fuel filter, if necessary, change. Clean the carburetor, watch the effect. It will be necessary to delve into the ignition system, configure. To check the fuel system, you can pour several grams directly into the cylinder through the candles of the candle, screw the candle and try to start. At least a trimmer for the grass should make the sounds of a running engine within 1-2 seconds and a little smoke should fly out of the silencer.

If you do not start a trimmer for grass at all or immediately stalls after the start of the start, then you first need to look for the reason in the main nodes and units, for this you need to carry out the test in the following sequence, so this sequence: this sequence: this sequence: this sequence:

In these nodes, the whole problem may be consistent.

The main malfunctions of gasoline and electric trimmers

In the lawn mower and an electric trimmer for grass, if you do not consider breakdowns associated with the bar and the mowing head, the malfunctions mainly happen in the engine area.

Damage of gasoline trimmers

Typical breakdowns of a gasoline trimmer for grass, which are most often faced with the owners of this unit, are as follows:

• engine breakdown;
• problems with the carburetor;
• problems with the supply of fuel;
• muffler malfunction;
• gearal breakdown;
• The starter broke;
• Air filter problems;
• Broken a buckshot on a gas tank.

Malfunctions of electric trimmers

Since the device of an electric coser is much easier than a motirmer, then there are few reasons for its failure.