Trimmer for grass does not develop power.

The reasons for the fall in the motorcycle. The lawn mower does not develop full power

Any person owning a country or land plot is well aware of the problems of the fight against excess vegetation. Now a trimmer for the grass has come to the rescue, which successfully replaced the usual braid in this field. This unit is very convenient in work, but it, like any mechanism, also, due to difficult working conditions or incorrect operation, is characterized by failing. Situations are quite common when a trimmer for grass does not gain momentum. To understand this problem, it is necessary to understand some aspects related to the functioning of the device.

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

• turn on the ignition button;
• press the silicone button for pumping gasoline several times;
• close the air damper;
• The gas lever is installed in a position for high speeds;
• first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

The reasons for the weak.speed trimmer for grass

If users complain to the trimmer for grass, which does not gain momentum, this means that it works normally on idle, and when pressing gas does not develop the necessary power. This can happen as a result of a long downtime of the apparatus without activity. These problems are typical for gasoline devices, including the Husqvarna 128R, STIHL FS 38 and Hitachi different modifications.

Working with a trimmer, you need to monitor its behavior all the time. a drop in revolutions and unusual noises signal the malfunctions in the aggregate. Sometimes you give gas, and the trimmer for the grass swims. In such cases, the work should immediately be suspended, let the mechanism cool and start searching for possible problems. They can be of a different nature of both the technological plan and external factors related to the conditions and features of the operation of the device.

External factors

Several factors that are not related to its breakdown affect the reduction of revolutions:

• filter pollution due to the hit of particles of dirt and dust in it;
• use of poor.quality fuel;
• incorrectly prepared mixture (relevant for trimmers with two.stroke gasoline engines);
• pollution of the muffle of muffler particles of vegetation, soil elements and other objects.

In this case, in the second and third cases, the formation of a soil in the combustion chamber is formed, and the elements of the carburetor are clogged.

technical issues

The technical problems of the lawn mower mainly occur in the fuel and ignition system. You can cope with them yourself.

• Когда ручная косилка не заводится или глохнет, проблема может быть связана со свечой. The dark cargo speaks of poor carburetor adjustment and low gasoline quality.
• The reason for the incorrect operation of the trimmer for the grass may be clogged fuel hose. Filters are also often clogged.
• Another internal problem. the muffler is covered with soot. From this, the turnover of the grass for the grass falls strongly. Output. you need to clean the muffler.

Important! If the unit does not work due to breaking up the engine, serious problems may occur. In this case, the malfunctions that can be eliminated with your own hands include only the destruction of piston rings. With more serious problems with the motor, if there is no warranty, you should be prepared to visit the workshop.

The lawn mower stalls

When buying a chainsaw, you should be prepared for the fact that, like all such tools, damage may occur that will require repairs.

But do not immediately run to the service center and pay a lot of money to the masters, convincing them of a serious defect in the device.

The lawn mower stalls at high speeds

Probably, the most common complaint about gasoline trimmers for grass is as follows: “The gasoline lawn mower jams”.

The reason for this, of course, may be a sufficiently serious malfunction. The engine of a two.stroke trimmer for grass does not develop turns and ceases to rotate. The FS 130 gasoline lawn mower gives gas and stops. However, in most cases, the situation is even simpler than it seems at first glance.

What to do with such a misfortune, first try to deal with its causes without the help of others, because, having found the reason, it’s even easier to cope with the trouble, and sometimes it is even self.destructive.

In fact, circumstances, that is, when gasoline burns at high speed, there are many.

Why is a Chinese lawn mower not developing momentum?

Trimmer for grass does not gain speed. a very common malfunction, which, of course, does not always have a regular solution.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

The first launch of new gas stations.Removing the grid from the silencer, began to work.

Another factor is the occurrence of failures in the energy system.

In this case, a braid for grass will stop at idle. At idle, the main secateur stops. GoodLuck 4300 chainsaw stops at idle video. The lawn mower stops when you press the accelerator pedal. The gasoline lawn mower is turned off at high speed. Problems with the power system can be caused by improper carburetor adjustment or incorrectly adjusted carburetor.

Excessive adjustment can be caused by vibration that occurs during the operation of a braid for grass.

However, an incorrectly adjusted chainsaw can be corrected by adjusting it in accordance with the recommendations of the user’s management.

In addition, sometimes gasoline trimmers for grass can be jammed due to the fact that the valve in the lid of the fuel tank just clogged or clogged.

To check this, try starting a trimmer for the grass by unscrewing the fuel tank cover.

If the device works fine in this mode, clean the valve.

Some tricks of work with a benzotrimer.

Now is summer, and gasoline engines have become a constant attribute on land plots. Great tool, powerful and mobile. You can mow grass with a gasoline trimmer and cut dry weeds. But sometimes the braid for grass does not start, works with interruptions or does not develop full power. Now, of course, is not the time to work! As they say, this is rather the vibration of the starter handle than the kosba.

Problems with the launch do not only have an old braid for grass, but also in the new. what is the answer? Only one thing remains. listen to expert advice and adopt their practical experience.

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

Some tricks of work with a benzotrimer.

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

The lawn mower stalls at high engine speeds

During operation, a situation arises when, when pressing the fuel supply key, the aggregate turnover begin not to increase, but to decrease. A malfunction of this nature can be caused:

Fuel hoses Motokos with filter

• etching of atmospheric air into the combustion chamber;
• problems with the circulation of a mixture of fuel;
• clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
• Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

The lawn mower does not develop speed.Another reason

The analogue of Husqvarnana develops the reason, the reason was very simple (watch in the video)

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. Why is a Chinese lawn mower not developing speed, the cause of Husqvarna. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

Why is a benzotrimer not gaining momentum and strangle

A braid braid with a gasoline drive is a necessary thing to owners of personal plots, lawns, and when a trimmer for grass stalls at one moment, the work on cleaning the area from the grass stops. The device itself is a rather difficult mechanism, because there are many different circumstances of its breakdowns. As a rule, the emerging problems contain an annotation for operation. Know the prerequisites for why the trimmer stalls for the grass, it should be that without the help of others to perfectly perform the repair of the device.

Problems with a benzocosa associated with the purpose that this device is not started, specially classified by specialists of service services. They stand out malfunctions with such nodes of the mechanism:

In order to correctly find the knot where the breakdown occurred, you need to study in what circumstances the trimmer stalls for the grass.

If the lawn mower stops when pressing the gas, then the prerequisites are usually subsequent.

• The more increased option is a carburetor adjustment failure that appears with significant load loads after a long.term inaction of the mechanism or when using it in languid criteria.
• The clogging of the fuel valve, which eliminate it with the message, and as a result, gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. There is also a tensile of the fuel hose directly to its gap, caused by the action of a significant load.
• The clogging of the soundtress (revolutionary valve), for this reason, does not enter the fuel in the tank.

What to do if the chainsaw does not throw off the moment?

The opposite previous situation is the one when the gas tools very quickly reaches high capacities and does not slow down. In this case, it can be observed that neither a screw on the case, nor cleaning the carburetor, this is not to eliminate. It would seem what else is needed, the saw works, gives out power as in the instructions. But the trouble is that in this case, in this case, you need ten times more than usual.

Read trimmer for grass gasoline stalls at high speeds the reason

If the gasoline on the candle of the chainsaw is fixed, and the cutting device itself does not work normally, then this indicates an excess of the air fuel mixture. The reason for this condition may be a failure in the adjustments of the carburetor, clogging of its jacklers, as well as the incorrect start of the mechanism. In the case of fixing on a candle characteristic soot, it is possible to talk with sufficient confidence about the incorrect functioning of the carburetor or the use of low.quality gasoline.

With all the above signs reflected on the spark plug, it is necessary to remove the carburetor and check its technical condition. Carburetor, when clogging, should be thoroughly cleaned, then adjust the device according to the technological requirements and replace the gas used in the tank. It should always be remembered that the carburetor is a rather complex node, consisting of many small components, details and tubules. Therefore, its repair should be carried out with particular caution and accuracy.

In addition to the restoration of the carburetor, it is necessary to check on the stand and the performance of the spark plug itself and, if necessary, set the correct gap in it. If the candle and its work do not like it at all, it is recommended to replace it with a new candle.

Engine starting problems

It is very important to determine the cause of the failure correctly, because otherwise we simply cannot eliminate it. If there are no extraneous sounds when trying to set up a chainsaw (knocking down, grinding, etc. D.), It often turns out that in fact there are no problems. For example, if you put the chainsaw and pull the fork for a long time, the engine simply pours and starts very much.

To properly start the engine saw engine, set the lever or switch to the “flap” position. Then you need to pump the mixture into the carburetor if there is a fuel pump in stock. Pull out the starting handle until the engine resistance becomes noticeable, and energetically extend the amplitude, taking your hand to the side. After two. Three such movements, the engine must first start, and then decay. If this does not happen, then it is necessary to transfer the lever to the position of half.gas or simply to the working position, and then continue to work the chainsaw in this mode. Many Pologaz chainsaws are recorded automatically when the air damper is pulled. Some models have an ignition with the key, it is important to make sure that it is turned on.

If the engine does not start, the first thing to do. unscrew and check the spark plug. There are times when the plant fills the burner with fuel in the cold season. Then you also need to unscrew the candle, dry the combustion chamber with one plant, clean the spark plug, screw it up and repeat the start. It is advisable to immediately check the presence of a spark. On a twisted candle, we put on a cap with a high.voltage wire, we put it on a cylinder, and we pull the starter. Visually observe a frequent blue spark. OK. We twist the candle in place and launch it. If there is no spark, change the candle and repeat the attempt. Again, no. Check the connection of the high.voltage wire to the spark plug, coil and ignition system.

In general, the condition of the candle can be used to determine the type of malfunction.

• Dry. Most likely, the fuel mixture is not included in the cylinder. This is not a ignition system, so the candle is screwed and checked.
• Wet, strongly sprinkled with fuel. The cause of the excessive fuel mixture is to violate the launch rules, as described above, or if the carburetor is incorrectly set up.
• Covered with black carbon. This may indicate the use of poor.quality oil, an incorrectly configured carburetor or an incorrectly calculated ratio of gasoline and oil. The candle should be washed, cleaned of carbon deposits with a sharp object (awl or needle), rub the electrodes with a fabric and installed in place.

When checking the light of the ignition, it is necessary to pay attention to the gap between the electrodes: Normal is considered from 0.5 to 0.65 mm. Damaged or worn gasket should be replaced.

Correctly adjusted carburetor chainsaw provides its effectiveness at full capacity with the most economical fuel consumption.

The need for tuning a carburetor chainsaw is infrequent, since adjustment is originally performed by the manufacturer to achieve the optimal mode of operation. Adjusting screws are designed for a more accurate adjustment of the carburetor chainsaw, if necessary.

Among the causes of violation of fixing the adjusting screws are the most common:

• Strong vibration or damage to a protective cap. This rarely happens, but still happens.
• Serious engine wear (piston). Of course, in this case it is better to take care of repairing a chainsaw, but at the same time, adjusting the carburetor can improve its functionality for some time.
• Litter in a carburetor because of the low quality of gasoline or due to the formation of scale. In this case, in addition to adjusting the carburetor, it can be avoided.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common problem and of course does not always have a simple solution.In this.

What signs indicate the need to adjust the carburetor chainsaw?

• Firstly, the engine does not start or does not start, and then stops. This is most often due to the depletion of the fuel mixture.
• Secondly, a significant increase in fuel consumption and exhaust gas emissions. An increase in the exhaust indicates that the fuel does not burn completely, which means that the cause of the fuel mixture may be the cause.

The adjustment scheme of the carburetor chainsaw may differ slightly depending on the manufacturer (the process of configuring the carburetor of the chainsaw of a particular brand and the model is described in detail in the operating manual), but the general principles remain unchanged for all brands, the goal of adjusting the saw is a change in the quantity and quality (enrichment) of the fuel mixture supplied to the engine cylinder.

To find out how to set up a carburetor on a chainsaw, you must learn to distinguish between three screws (only one in some models).

The screws l and h are similar only to the form, in fact they are different

Each screw has its own designation of the letter:

• “L” is used to adjust low speed;
• “H” is required to adjust the upper speed;
• “T” is required to adjust the idle pass (for models with one screw there is only one).

There are mandatory safety requirements that must be observed when setting up a carburetor of any chainsaw:

• Make sure the chain is turned from you.
• The saw should be stable on a flat surface, and its cutting part should not touch any objects.

Please note: the exact values ​​of the angle of rotation of the adjusting screws can be found in the operating manual for your specific chainsaw model. Accurately following the manufacturer’s instructions, you can avoid engine damage.

The process of setting up a cardan carburetor consists of two stages: the base (the engine is turned off) and the final (working warmed engine).

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. The lawn mower does not develop speed.Why is a Chinese lawn mower not gaining. The lawn mower does not develop speed, why the Chinese lawn mower does not develop momentum. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds. There are quite a lot of these circumstances.

Another is the presence of defects in the power system.

In this case, the lawn mower will stall at idle. I did not give any tangible result. Why is a Chinese lawn mower not developing momentum. Why does my lawn mower not develops momentum. Why the lawn mower. I can’t from the ground.And the revolutions are gaining from the floor. Dilems with the power system may lead to a drainage or incorrect carburetor adjustment.

Why is a Chinese lawn mower not developing momentum ?

Chinese lawn mower Analog Husqvarna does not develop turnover, the reason was very simple (watch in the video)

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

This article will solve the case of a gas station when they stall at high speeds On gas

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common problem and of course does not always have a simple solution.In this.

What signs indicate the need to adjust the carburetor chainsaw?

• Firstly, the engine does not start or does not start, and then stops. This is most often due to the depletion of the fuel mixture.
• Secondly, a significant increase in fuel consumption and exhaust gas emissions. An increase in the exhaust indicates that the fuel does not burn completely, which means that the cause of the fuel mixture may be the cause.

The adjustment scheme of the carburetor chainsaw may differ slightly depending on the manufacturer (the process of configuring the carburetor of the chainsaw of a particular brand and the model is described in detail in the operating manual), but the general principles remain unchanged for all brands, the goal of adjusting the saw is a change in the quantity and quality (enrichment) of the fuel mixture supplied to the engine cylinder.

To find out how to set up a carburetor on a chainsaw, you must learn to distinguish between three screws (only one in some models).

The screws l and h are similar only to the form, in fact they are different

Each screw has its own designation of the letter:

• “L” is used to adjust low speed;
• “H” is required to adjust the upper speed;
• “T” is required to adjust the idle pass (for models with one screw there is only one).

There are mandatory safety requirements that must be observed when setting up a carburetor of any chainsaw:

• Make sure the chain is turned from you.
• The saw should be stable on a flat surface, and its cutting part should not touch any objects.

Please note: the exact values ​​of the angle of rotation of the adjusting screws can be found in the operating manual for your specific chainsaw model. Accurately following the manufacturer’s instructions, you can avoid engine damage.

The process of setting up a cardan carburetor consists of two stages: the base (the engine is turned off) and the final (working warmed engine).

The main adjustment of the saw carburetor

Slowly rotate the screws of adjustment of the maximum and minimum speed (h and l) clockwise until it stops, then turn counterclockwise 1.5 turns.

Before this adjustment step, it is necessary to warm the engine for 5-10 minutes.

Turn the blanket adjustment screw (t / la / s) counterclockwise to reach the minimum speed at which the engine will be stable. Make sure the chain does not move. That is, if the engine is idling at idle, tighten the idle speed adjustment screw clockwise. If the chain is set in motion, turn the screw counterclockwise.

To complete the tuning of the carburetor chainsaw, you need to check the engine for acceleration and maximum speed.

Carburetor device Motokos Chinese

Today, the question is relevant and open, what is briefly formulated as follows: carburetor motorcosa device. And if European and American production professional lawnmands in their instructions contain statements about setting up a carburetor, then the scheme of this element of a braid of Chinese.made grass is not yet available to a wide circle of users. In this article we will try to figure out: what is the special carburetor of the lawn mower, the country of which is China and how it differs from those, for example, which stand on the original Husqvarna, Stiles and, for example, Oleo-Mac, produced not in the PRC, but purely in Italy.

This unit will optimally paint by individual elements, and here we will indicate the difference from other types of carburetors of this copy:

• Fuel pump of a membrane type.
• Adjusting system with atmospheric membrane.
• Idle system.
• Dosage system with quality screw.
• Primer (popularly “podok”). helps to develop all fuel from the tank, and also facilitates the launch if you have not used the tool for a long time.
• The main detail is an elastic plate of complex shape, it contains two valves.
• The needle valve similar to the car. this is the adjustment system. When the pressure decreases, it closes with a special membrane. In the first photo. the second connector from the body, on the left.
• Dosing system with rotary type, where the latter rotates.
• The air damper in this type of carburetor is part of the air filter.
• The quality screw is located on the right in the center of the rotor, it is sealous.
• Idle system

Features of the device of the carburetor of the Stihl lawn mower

The diagram of the carburetor motor.cooker manufactured by the German company StiHL differs from the Chinese similar mechanism already in that it provides for manual tuning by the user. For this, screws L, h, t are installed here. If the protective cap of motorcycles is damaged, then they can unscrew and then the work will become disarmed. Problems can be quickly eliminated by returning a certain screw to the previous position. The same situation comes from excessive vibrations of the entire gas.trimmer apparatus. On the carba of a Chinese mowing, as a rule, only one screw is to regulate the idle.

Almost, any correction of the work of the carburetor of the braid for the grass of the Stihl FS 55 brand can be carried out independently using your hearing or a special device. a tanometer. You need to check only after the engine warms up. From the cognitive video, you will draw a useful information about the carburetor. For productive operation of the braid mechanism for grass, we will always offer high.quality, but cheap oil for the compressor, as well as any other accessories and spare parts.

https: // Fermerteh.ru/remont-karbyuratora-benzokosy https: // Domamaster.Net/Regulirovka-Trimmera-Svoimi-Rukami/https: // GLAV-DACHA.ru/regulirovku-karbyuratora-benzokosy/https: // www.Kosikosa.COM/Index.PHP?Route = Information/News/Infonews_id = 39

The principle of operation of the carburetor of the lawn mower

The throttle dashes determines the amount of air for supply, and the engine power directly depends on this.

Fuel is sucked into the carburetor system (its membrane). Then passes through the fitting in the carburetor. Next, the liquid moves through the intake and exhaust valve of the pump. Filtered with a net. The needle valve moves into the membrane chamber.

• Air supply to the tube with an air septum (damper). The partition regulates the intensity of the air flow.
• The fuel supply system is necessarily narrowed by a diffuser to increase the flow rate.
• Gasoline through the float chamber and nozzle with narrowing. The chamber with a float regulates the temporary volume of gasoline. In the float chamber, the pressure level is neutral, and in the tube with narrowing is already low. Thanks to the pressure drop, fuel penetrates through the jetler.
• Air flow acceleration contributes to the transfer of fuel (gasoline) and its spray. As a result, the air-fuel mixture of the necessary proportion or density is formed.
• The air-fuel mixture penetrates the engine cylinder through the fuel tube.

The level of air density in the system depends on the area of ​​the open air damper. The wider the damper is, the greater the fuel consumption and power.

Simply put, adjusting the carburetor on a benzocos. creating an optimal fuel mixture due to the correct air supply.