Trimmer Stalls When Opening The Air Damper

A spit that has a gasoline drive is a useful thing for owners of personal plots, lawns, and when the trimmer suddenly stalls, the work to clean the area from grass stops. The device itself is a rather complex mechanism, so there are many different reasons for its breakdowns. The most common problems are contained in the instruction manual. To know the reasons why the trimmer stalls, you should be able to effectively repair the device yourself.

What could break

Problems with the brushcutter due to the fact that this device does not start are classified in a certain way by service technicians. They highlight malfunctions with the following nodes of the mechanism:

  • engine in which the piston and bearings may wear out or fail, crack the crankcase;
  • fuel supply system, while it is possible clogging the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • ignition circuit.

trimmer stalls when opening choke

In order to correctly determine the node where the breakdown occurred, it is necessary to pay attention to under what circumstances the trimmer stalls.

When you press the gas

If the brushcutter stops when you press the gas, then the reasons may be as follows.

  1. The most common option is carb adjustment error, which occurs with significant loads on the drive, after prolonged inactivity of the mechanism or when it is used in difficult conditions.
  2. Fuel valve clogging, which eliminate it by relaxation, as a result of which gasoline starts to flow normally through the system.
  3. Loosening and drooping of the cable in the carburetor. May also occur fuel hose extension up to its rupture caused by the action of a significant load.
  4. Clogged breather (check valve), as a result of which fuel does not enter the tank.

If the problem is related to the carburetor assembly, then it can be recognized by the appearance of vibrations of the brushcutter. When the hose bursts or the cable is stretched, these components are replaced.

At high speeds

When the braid stalls at high speeds, then this is due to the following problems:

  • clogging or sticking of the valve located on the gas tank cap;
  • the carburetor is out of alignment under the influence of vibrations arising from the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • air leaks;
  • The fuel intake hose is cracked or loose.

Carburetor adjust, Based on the operating instructions for the trimmer. To adjust, it is often enough to loosen the tightening of its body. If there are problematic moments with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

Video: Trimmer Stalls When Opening The Air Damper


At idle

At idle, common causes of trimmer stopping are the following:

  • contamination, misregistration or improperly adjusted carburetor adjustment;
  • clogged air filter;

Replacing the Lawn Mowers Air Filter

Trimmer air filter

  • reducing the speed of the gearbox when it is heated, which is a consequence of the use of an unsuitable fuel mixture;
  • throttle clogging;
  • air entering the system;
  • not enough fuel to operate the brushcutter.

If the carburetor is the problem, then the equipment will stop both during a “cold” and a “hot” start.

Right after wound up

The unit may stall immediately after start-up, if the carburetor is misregulated or has been incorrectly configured. this causes uneven fuel supply. The result of this is that the device begins to vibrate distinctly. To troubleshoot, the carburetor is reconfigured according to the instructions for the mechanism.

Also the engine stops when it happens valve clogging, supplying fuel. In such cases, it is simple enough to clean it. If the lawn mower first worked, but then immediately died out, then perhaps the fuel enters the carburetor assembly with some difficulty. The easing of the valve helps to solve the problem, which ensures free circulation of the mixture in the system.

A stop can also be called. air suction in the presence of mechanical damage to the hose (holes, cracks), producing fuel intake. In this case, add revolutions to the drive in order to quickly expel air bubbles from the system.

When heated

lawn mowing often stops when heated. At the same time, it starts, works “jerkily” and gradually stops. This process occurs when gas in the carburetor boils or a shutter in it is installed rotary, and not disk type. In the latter case, the item is changed.

It happens that the trimmer heats up if ignition wire damaged either a coil. In order for the device to start working normally, replace parts.

When opening the choke

It happens that the unit stalls when the air damper is opened, normally idling. This is due to air leaks in the system caused by the presence of fuel hose cracks or problems with oil seals. The carburetor dosing system may also malfunction, while the lawn mowing will stop after the shutter is opened.

Carburetor fuel hose

All possible reasons that the brushcutter stalls, and how to eliminate them are contained in the next video

There are many reasons for stopping the lawn mowing, but the most common problems in operation are related to its carburetor. They can occur in any cases. The most problematic option is when a serious breakdown occurs, and you will need to purchase new parts or change the brushcutter.

In order for the trimmer to work normally for a long time, the requirements of the operating instructions must be strictly observed. It is necessary to refuel the unit with a suitable fuel mixture, the device should work at moderate load.