The importance of winding correctly
In order for fishing to be successful, you need to carefully prepare for it. Otherwise, “terrible things can happen”. the weather is wonderful, the bite is excellent, and the tackle constantly fails and prevents you from taking advantage of favorable fishing conditions.
To prevent this from happening, you need to set up all fishing accessories in advance. One of the most important steps in preparing for fishing is the correct winding of the line on the spool of the fishing reel. Failure to comply with the basic rules threatens the would-be fisherman with entanglement and line breakage, and fishing instead of pleasure will become a test for the nervous system.
The casting distance depends on the quality of such work. Correct winding ensures the casting of the bait at a distance that best matches the technical characteristics of the reel.
In addition, high-quality winding extends the life of the line by reducing mechanical friction and reducing the risk of “beard” when casting, which often requires cutting the line. Therefore, before starting work, it is necessary to consider a few tips from experienced fishermen on how to lay the line on the spool. This is a fairly simple procedure that even a beginner can handle.
What is backing?
It is usually difficult to determine how much line to spool. A standard bobbin is believed to hold one hundred meters of 0.3mm line. However, progress has stepped forward, and modern lines are becoming thinner, and not losing a margin of safety.
How many meters of fishing line to wind on the reel, each angler decides for himself, depending on the fishing conditions. Therefore, it happens more and more often that the selected line is much smaller than the spool can accommodate. The resulting free space needs to be filled with something. Some people use electrical tape or nylon thread for THESE purposes, but this is NOT the best option. The adhesive on the insulating tape, which holds the lower turns of the line, quickly peels off. And the nylon thread dries for a very long time when wet.
Therefore, more and more fishermen are inclined to the American method. to reel in the lower layer of fishing line, which is simpler and cheaper, and tie the main, higher quality to it. This turns of inexpensive whining is called backing, in our opinion. reeling. It connects to the main strap with a self-tightening double loop, Clinch or similar knot options.
Determining the amount of rewinding
In the question of how to wind the line on a reel, for beginners there is a difficulty in determining the amount of winding. It can only be established experimentally. Experienced fishermen advise to reverse the order.
If there is a second reel of the same, you need to wind the fishing line on it first, and then the reel attached to it. In this case, you should remember the basic rule: you can correctly wind the fishing line on the spinning reel only if the level of its top layer does NOT exceed 3 mm from the side of the spool. After that, Rewind the thread to the main Shula, already starting with Buckingham, which, as expected, will be below.
If there is a second of the same reel, the measurement is made on the main reel, then the line is unwound and rewound on it, already starting from the reeling.
Winding profiles (taper)
In different reel models, the turns of the line on the spool are applied in different ways. In quality products, the cylindrical and conical winding method is used. The line laid in profile forms a straight line. With a cylindrical winding, this line is straight, parallel to the spool, with a tapered one. oblique.
The straight tapered shape tapers towards the front edge of the spool, the reverse one widens. Straight taper reduces line friction. Reverse styling Reduces the chance of spontaneous line drop.
There is also a third type of winding. chaotic. Usually used in cheap Chinese fishing rod. And if such a winding can still be tolerated, using an ordinary fishing line, then the use of a cord in such a reel should be abandoned. Bad casts, beard, overlaps and entanglements are guaranteed. This leads to mishaps in fishing and can also ruin the mood of every fisherman.
Hand winding precautions
Since the operation is performed with the obligatory tension of the fishing line, you need to press it by hand to the rod just above the first ring in order to adjust the tension. In this case, you should know how to wind the line on the reel, and not cut your fingers with it. You can put a glove on your hand. And you can skip the line between the pages of a small book, then it gets additional alignment during the winding process.
Winding the thread by hand
You should also consider how to wind the line onto the reel by hand. If a fisherman has a telescopic spinning rod, it must be expanded into working condition. This is optional for a plug rod, you can work with the bottom of it.
Attach the spool to the spool seat. There is a hole in the spool on which the line is wound. A rod is inserted into it, which can be used as a pencil, pen, knitting needles, etc. If there is an assistant in the fisherman, he will hold here, on which the bobbin will be unwound. If the assistant comments, you can hold the rod yourself between your knees.
On sale there are special devices for unwinding the line from the reel. Their advantage is that they regulate the force when winding the line and make it uniform.
The line is threaded through the rings, from the smallest top element into the spools. The thread is then secured into the spool with the line guide open. After that, it is lowered into the working position. You can start winding the line by rotating the spool.
Winding device
Many “craftsmen” come up with their own ways of winding. For example, you should consider how to complete the task at hand with a drill. To do this, you need a nail, which almost fits into the spool hole and a 7.5 mm thick circle of rubber.
The hardware is inserted in the center of the rubber and placed in the spool. The structure is clamped in a drill chuck or screwdriver. The line is fixed in the spool with a knot.
In one hand, you need to hold the bobbins of thread along the central hole, in the other. a drill. Winding is performed clockwise, adjusting the revolutions of the chuck. How to wind the line on the reel of a fishing rod correctly with such a device? To do this, you only need to drive the line up and down, Make sure that it lays down evenly.
Storage rules on spool
For the line to last longer, you need to properly care for it. We send the tackle for long-term storage, the line should be completely unwound and dried thoroughly, otherwise it will lose its elasticity. This is fraught with rupture at the most inopportune moment. You can use a hair dryer to dry. When the line is completely dry, you need to wind it on a spool.
In general, you need to dry the thread after each fishing trip. Only this should not be done along the entire length, but only on an area slightly larger than the length of the long cast.
How to wind a line on a reel: instructions
We collect tackle for fishing, periodically it is required to change the line on the reel. This is a fairly simple procedure. However, it has a number of nuances. The correctness of such a procedure will depend on whether the thread will be flat when casting or will start to get confused. If the fisherman does the wrong thing, the thread may break. This causes a lot of problems. To avoid such troubles, you need to consider in detail how to wind the line on a reel. This technology will be discussed in detail in the article.
Instructions with step-by-step descriptions of how to wind the trimmer reel and lawn mowers
In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually provided for a tip, which will NOT allow you to make a mistake using the appropriate equipment.
If the information on the reel is about the diameter of the fishing line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all are applicable. We will consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.
It is interesting! The principle of how to wind up the line to guide lawn mowers is appropriate Not only for autonomous gasoline units, but also for electric trimmers.
Winding the line to the trimmer
Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:
- Trimmer head with one working Mustache;
- Bobbin with two tendril fishing lines;
- Auto winding reel.
Single Barbed Trimmer Spool
Reel for single-barb lawn mowers
Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.
After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.
What you need to know about trimmer line
A fishing line is called a consumable, which consists of nylon, and serves as a cutting device. By means of this equipment, grass slopes occur, which is ensured by rotating the tool head at a high frequency. This material has different thicknesses, which depends on its use on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3. 2 mm).
The more powerful the tool, the correspondingly thicker the cutting tool should be. This not only affects the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and recharge the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the Step-by-step instructions for replacing the line in the trimmer reel.
Features of the use of trimmers
A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, row spacing in a garden plot.
Such a convenient, and most importantly, effective device like a trimmer exists in several variations:
- Petrol;
- Rechargeable;
- Electric.
As it is clear from the name, the trimmer types differ markedly from each other. But regardless of the type of this tool, its cutting element may be a fishing line. Of course, the line tucked into the trimmer reel is NOT infinite. And sooner or later you will need to replace it with a new one.
Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?
Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line for a trimmer, and will be discussed in this article.
How to wind the line around the mowing head of lawn mowers (trimmers)
Find out more on our website: Subscribe to our YOUTUBE channel! We are always glad to cooperate!
Now only I bite!
I caught this pike with a bite activator. No more fishing without a catch and searching for your bad luck! The time has come to change everything. The best bite activator of the year! Made in Italy.
How to properly wind the line on the trimmer reel with your own hands: we paint the essence
What line is used for the trimmer? How to remove the spool from the trimmer? Threading bobbins with different types of bobbins. A Few Tips for Proper Trimming.
How to wind line around the trimmer cutter head or lawn mowers
Shows in detail how to wind the line on a trimmer reel or lawn mowers. Refueling with mowing line.