A snowmobile from a tiller on tracks with your own hands

How to make a snowmobile from a tiller yourself

This snowmobile can be made in a few weekends in the garage in the country. At first glance, its design looks very simple. If we compare its cross-country ability in wet or loose snow, it will not yield to many industrial snowmobiles..

The creation of the snowmobile was based on the principle: the less weight and the larger the track size, the higher its passability on deep and loose snow. Therefore, the design will be as lightweight as possible..

How to make a homemade snowmobile from a tiller on tracks

Four wheels are installed inside the track. When there is movement, they roll along the conveyor belt, with the lugs fixed. The track is driven by a chain from the motor, special drive sprockets, through the driven shaft. They were removed from Buran.

The engine is taken from a conventional tiller, which has 6 hp. You can’t accelerate quickly on it. The soft suspension of the ski and track has been removed because the snowmobile is designed to ride on loose snow. This simplifies the design and reduces the weight of the snowmobile..

Snowmobile Track Making

Consider the process of making a caterpillar. Plastic water pipe 40 mm, cut to length 470 mm. They will be used to make blanks for lugs. Then each of them is sawn lengthwise into equal parts with a circular saw.

The lugs are attached with furniture bolts to the conveyor belt. When making a track, it is imperative to keep the lugs at the same distance. Otherwise, the drive sprocket teeth will “run over”, as a result of which the caterpillar will slip and slide off the rollers..

To drill holes in the conveyor belt for the fastening bolts, a jig was made. To drill the holes, a wood drill was used with a special sharpening.

This jig allows you to simultaneously drill six holes in the conveyor belt to attach three track lugs. We also purchased leading sprockets (2 pcs), an inflatable rubber wheel (4 pcs), closed bearings 05 (2 pcs).

A turner made a bearing support and a track drive shaft. The snowmobile frame is self-made. For this, square pipes 25×25 mm were used. The articulated pivots of the steering wheel and skis are in the same plane and on the same mowing line, so a continuous steering rod without ball ends was used.

Ski turn sleeves are quite easy to make. A 3/4 inch water sleeve is welded onto the front cross member of the frame. Male threads are screwed there. To them I welded the bipod of the ski rack and tie rod. Angles are installed on the skis, which serve as attachments to the pivot stand of the snowmobile. A metal undercut is made from the bottom to better control the snowmobile while driving on packed snow or crust.

Making homemade products – a snowmobile from a tiller video and description

From the tiller, you can also use the reverse gear, centrifugal clutch, steering and fuel tank. Next, you need to think about the propulsion of the snowmobile. Most of them are equipped with a caterpillar drive..

Chain tension is adjusted by motor offset

The handling of the snowmobile is quite simple. To increase engine speed, the throttle stick is used, which is located on the steering wheel. This engages an automatic centrifugal clutch, causing the snowmobile to move. Since the engine power is low, the speed of the snowmobile is 10-15 km / h. Therefore no brakes are provided. To stop, you need to slow down the engine speed.

Tracks are available in any width. Choose what is more convenient to do: a narrow but long caterpillar, or a wide but short one. It is important to remember that a larger track will put more stress on the engine and make it more difficult to control the snowmobile. If the caterpillar is made small, then the car can fall through in deep snow..

The weight of the snowmobile with all parts is 76 kg. It includes: steering wheel and engine (25 kg), skis (5 kg), wheels with axles (9 kg), drive shaft (7 kg), caterpillar (9 kg), seat with racks (6 kg).

It is possible to reduce the weight of some parts. For this size of tracked snowmobile, the weight is quite satisfactory..

The best homemade products – a snowmobile from Tiller

When making a homemade snowmobile, they use tracks from other snowmobile machines, or homemade ones, assembled from scrap materials. After choosing a track, you need to decide what type of suspension to use. There are two main types to choose from: roller suspension and skid suspension.

Each of them has both advantages and disadvantages. After that, it is important to decide what layout the snowmobile will have. Usually, two steering skis are installed on the front of the snowmobile and a track block at the rear..

The engine can be installed in both the rear and the front of the snowmobile.

Characteristics of the resulting homemade snowmobile

frame length 2000 mm;
track width 470 mm;
between the axial distance of the support rollers 1070 mm.

How to make homemade tiller tracks

Here we will consider several methods of making caterpillars with our own hands, with good performance characteristics..

The easiest version of homemade caterpillars

For light all-terrain vehicles and snowmobiles, the tracks can be made from a conveyor belt and a sleeve-roller chain. To make such a caterpillar, it is not necessary to own a special tool, everything can be done “on the knee”.

To extend the service life of the tape, it is necessary to stitch it along the edges with a fishing line, observing a step of 1 centimeter, which will protect the tape from fraying. To connect the ribbon in a ring, you can sew the ribbon from the ends, or use a hinge.

Tricycle the DNIEPER.Homemade product.Motorcycle Dnepr + VAZ 2101=cargo motorcycle…Own hand

Choosing the thickness of the tape should be based on the power of the engine. If you use engines from domestic motorcycles, it is enough to take a belt with a thickness of 8-10 mm, used on conveyors in agriculture..

Such a self-made snowmobile track has a good resource, and is easily repaired if necessary..

Homemade track for a motorized towing vehicle

It is very common among home-builders to make tracks using car tires. For this, tires are selected, which have a suitable tread pattern, from trucks..

To make such a caterpillar, you need to cut the beads from the tire and leave the treadmill. This is a rather laborious work that requires good patience, because the tool used is a sharpened boot knife.

To make the work easier, from time to time the knife blade can be moistened in a soapy solution to cut the rubber faster. One option is to use a homemade cutting device, or use a jigsaw with a fine-toothed file..

After cutting the beads, if the track is too hard, you can remove the excess layers of rubber inside the resulting ring. If the tread pattern is not suitable for the conditions of use, then a new lug structure is cut.

The undoubted advantage of a home-made caterpillar from a tire over a caterpillar from a conveyor belt, in an initially closed circuit, and therefore reliability. The minus of this caterpillar is in the limited width of the workpiece, which can be corrected by using a double-width option.

We make homemade caterpillars for the tiller: photos, videos, recommendations

Many people involved in the manufacture of homemade equipment also develop tracked ATVs and homemade tracks for a tiller. When putting this idea into practice, people use a variety of solutions. But the manufacture of caterpillars remains a big problem for fans of this type of transport..

After all, if an all-terrain vehicle or snowmobile is made by hand, then the caterpillars should be homemade..

Belt tracks

This caterpillar manufacturing option is attractive for its relative simplicity..
To do this, you need to connect the belts with V-shaped profiles into one piece with screws or rivets, using lugs attached to the belts.

To make holes for the drive sprocket in such a track, you need to make gaps between the belts.
You can find many ways to make caterpillars with your own hands – the main thing is to have patience, desire and perseverance – then everything will work out.

Let’s go to practice

A frame made of pipes or corners is primarily equipped with a steering gear. Having chosen the height and angle of inclination, weld the element with spot welding. Install and fix the engine according to the drawing, taking care not to tilt too much. The snowmobile should not have a long fuel line, so try to position the tank closer to the carburetor.

The next step is to install the track. Attach the driven axle with the belt fitted to the rear of the frame (on a fork, suspension, shock absorber, etc., depending on the type of construction), the leading axle in the middle of the snowmobile (most often under the driver’s seat), in the shortest possible hitch with the engine. The gears of both axles are pre-engaged.

Further, minor work is carried out: the fuel tank is connected, the throttle and brake cable is connected, the seat is installed, etc..

How to make a snowmobile on tracks with your own hands?

With the onset of the winter period, two-wheeled vehicles are losing their relevance. Using a car to overcome short distances with high snow cover is not particularly practical, and in most cases it is impossible. The snowmobile copes with this task much better..

A winter motor vehicle is in most cases equipped with a rear-wheel drive track and front steering skis. High cross-country ability, versatility and ease of use make the snowmobile by far the most popular means of transportation in the winter season..

How to make homemade caterpillars?

One of the most common materials for making a propulsion unit at home is a car tire. A self-made track for a snowmobile from a car tire has one important advantage over other options – it is made in the form of a closed loop, which significantly reduces the likelihood of rupture.

The beads are separated from the tire using a boot knife, leaving a flexible treadmill. The lugs are attached to the drive blade – plastic pipes sawn along with a diameter of about 40 mm and a thickness of about 5 mm. Cut to fit the width of the tire, half-pipes are attached to the canvas with bolts (M6, etc.) at intervals of 5-7 cm.

In the same way, home-made tracks are made from a conveyor belt. Their main advantage is the ability to choose the length of the propeller. After cutting to the required length, special attention should be paid to the hitch. The ends of the tape overlap each other by 3-5 cm, and are fixed across the entire width with the same bolts as the lugs.

DIY materials such as V-belts are often helpful in making homemade tracks. Fastened in width by means of lugs, they make up a full-fledged caterpillar track with hollows for the gear already existing on the inside..

Note that the wider the track, the better the snowmobile’s flotation, but the poorer the handling. Factory options have three samples of canvas width in inches: 15 – standard; 20 – wide; 24 – ultra wide.

Homemade snowmobile on tracks with your own hands: where to start?

1 – rear light; 2 – hitch; 3 – body (plywood, s16); 4 – side reflectors; 5 – rear shock absorber (from the Dnepr motorcycle, 2 pcs.); 6 – gas tank (from the launcher of the T-150 tractor); 7 – seat; 8 – main frame; 9 – electronic ignition switch (from the Voskhod motorcycle); 10 – ignition coil (from the Voskhod motorcycle); 11 – power plant (from a motorized carriage, 14 hp); 12 – muffler (from motorized carriages); 13 – steering column; 14 – steering joint in a leather case filled with grease (joint from “UAZ”); 15 – limiter for vertical movement of the steering ski (chain); 16 – steering ski turn limiter; 17 – steering ski; 18 – side ski (2 pcs.); 19 – generator; 20 – clutch lever (from a motorized carriage); 21 – drive chain shield; 22 – footboard; 23 – drive shaft drive chain; 24 – the drive shaft of the caterpillar; 25 – lower track chain guide (polyethylene, s10, 2 pcs.); 26 – caterpillar chain (from the header of the forage harvester, 2 pcs.); 27, 31 – upper front and rear chain guides (polyethylene s10, 2 pcs.); 28 – shock absorber of the propeller hinge frame (shortened rear shock absorbers of the Dnepr motorcycle, 2 sets); 29 – support ski; 30 – rear spacer frame; 32 – rear axle.

A drawing of a homemade snowmobile is the most important stage in the preparatory stage of manufacturing. Here, engineering skills will come in handy, and in the absence of such, surface sketches are made, creating a general image of the future mechanism.

Before creating a drawing, it is necessary to determine the list of required components. The basis of the standard configuration of the snowmobile is:

• Frame – depending on the complexity of the design, it can be borrowed from an ATV, motor scooter, scooter, motorcycle, etc. In their absence, the part is usually cooked from thin-walled metal pipes with a diameter of about 40 mm.
• Seat – given the difficult operating conditions of the equipment, the material of this element must have a high moisture-repellent ability.
• Engine – is selected with the calculation of the required speed and the total weight of the vehicle. The most commonly used motors are tillers, scooters, motorcycles, etc..
• Tank – 10-15 liter metal / plastic container will fully provide carefree trips over relatively long distances and will not take up much space on the unit.
• Skis – in the absence of ready-made options, it is recommended to use nine / ten-layer plywood sheets with a thickness of about 3 mm for self-production.
• Steering wheel – chosen with the calculation of convenience and practicality. Similar to frame, engine and seat, retracted from the specified two-wheeled units.
• Drive – a part that transfers rotary motion from the engine to the track. This function is well performed by a motorcycle chain..
• The caterpillar is the most complex and important element. Their types and methods of self-production will be discussed further..

Features of homemade snowmobiles

Nowadays, you can buy a snowmobile in any motorcycle showroom, both in a large metropolis and in a small city, however, the prices of this equipment force many winter driving enthusiasts to make a homemade snowmobile on tracks with their own hands.

There are four important advantages of a self-made vehicle over a factory one:

• Price is the most important factor for most. The cost of some units of leading manufacturers of motor vehicles can exceed the cost of assembled from scrap materials by 5-10 times.
• Parameters – the ability to assemble a vehicle of the desired configuration. This applies to both the appearance and the power reserve, the type of chassis, etc..
• Reliability is the point that even well-known manufacturers do not always boast of. When self-manufacturing, a person uses the highest quality materials and pays special attention to the most important components of the mechanism.
• Benefit – the ability to use materials, parts and devices from other devices lying around in garages and backrooms.

[sc: ads3]

At the same time, homemade snowmobiles find their application, both on the streets of settlements, and on roadless areas of suburban expanses and ski resorts..

Homemade snowmobile from Tiller

This transformation is especially popular today. the tiller can be used partially or completely. In the first case, a supporting frame with a rear axle is added to the unit (engine with steering fork and wheels). The most difficult step in this case is the transformation of the tiller’s working shaft into a drive gear.

A homemade tiller snowmobile with partial use of parts is more versatile. In this case, only the engine and the steering fork are removed from the “donor”, to the bottom of which skis are attached instead of wheels. The motor itself can be located at the rear of the structure..

It should be noted that the engines of the main part of the tillers are designed for the weight and pressure of the wheels, which is several times less than the tracked one. Therefore, in order to avoid increased wear of parts and fuel consumption, it is better to equip such a snowmobile with low pressure wheels..

DIY homemade snowmobile from a tiller

The tiller is a versatile tool for agricultural work. The device is considered universal due to the fact that the design assumes the possibility of its reorganization. You can make an ATV or a snowmobile from a tiller with your own hands. Such re-equipment does not require significant financial costs or skills, and at the same time one machine will perform many functions..

It is advisable to remake a tiller for a snowmobile, if only because of the price: the cost of the most primitive machine for moving on snow ranges from 3.5 thousand to 5 thousand dollars. There are also models costing more than 10 thousand dollars..

Not everyone can buy a regular snowmobile, so if you urgently need a winter vehicle, you can use a tiller. Such homemade products are very popular among rural residents..

Converting a tiller into a snowmobile

The first and second stages are to make the frame and mount the power unit:

• The frame is made from old motorcycle or car pipes. A pipe bender will help to shape.
• The joints are spot welded.
• Move the engine to the center of the body structure.
• We place the engine on a specially made platform with fasteners for fixing the motor itself.

Mounting the motor on a special platform is very important, since otherwise it can become clogged with snow and burn out as a result..

The installation of the steering wheel and seat is chosen by the master independently – the main thing is that it is comfortable to operate the device. Depending on the power of the engine, the snowmobile can accommodate several passengers.

The third step is to install the runners. Most often these are two wide skis that are attached to the steering column with hinges. The front part, which secures the runners, must be equipped with shock absorbers..

Instead of skis, you can use tracks or wheels (pneumatics). Each option has its own pros and cons.

Drawing of a simple snowmobile

Tiller snowmobile on wheels

The main attention should be paid to the choice of the power unit – the motor on the tiller should be as powerful as possible, otherwise the unit will not be able to perform its specific functions – moving on snow or ice.

It is important to properly design the drives and frame of the ATV. It is desirable that each wheel has a separate drive. This will greatly simplify handling in extreme conditions. For a snowmobile, four wheels are most often used, as three-wheeled vehicles are less stable.

Low pressure wheels and wide skis are often combined. Thus, the stability and maneuverability of the vehicle increases, but maneuverability does not decrease..

Homemade snowmobile on wheels

DIY mini snowmobile

Mini snowmobiles are very popular means of transportation during the winter season. Such a unit is found in the suburbs, but in the village it is simply irreplaceable. At the same time, mini-snowmobiles have many advantages over standard snowmobiles:

• High cross-country ability and maneuverability.
• Economical fuel consumption.
• The method of making a mini snowmobile is easy.
• Available Crafting Materials.
• Takes up little garage space.

Due to its compact dimensions and minimal weight, the unit passes through the most inaccessible places and practically does not fall into loose snow. If you correctly think over all the nuances of manufacturing, you can get by with minimal financial costs for re-equipping the unit.

Snowmobile of the pipe-stick type

Home-made caterpillar motoblock snowmobiles can be divided into two main groups, depending on the material of the snowhooks: “pipe workers” and “stick insects”. They differ in the material used for the tracks. To make the structure of the tracks more durable and resistant to deformation, pipes (ordinary plastic plumbing) are used. But in this case, the traction of tracks and snow is not high..

Drawing of caterpillars for a stick insect snowmobile

Another variation uses a timber beam for the tracks. The service life of this method of arranging tracks is not very high, but the adhesion to the surface is much higher..

Tracked snowmobile

Tiller snowmobiles on tracks are characterized by high cross-country ability. But because of the huge mass, they are harder to manage – agility deteriorates. In addition, the cost of installing tracks is different from skis or wheels..

You can make your own tracks, but this is a long and complicated process. At the same time, there are several features of a tracked vehicle for passing through the snow:

• The motor is installed in the traction part, so the tiller frame will have to be significantly altered.
• If the tracks are made independently, then attention is paid to the quality of the joints..
• The seat and steering section are installed so that the balance of all components of the unit is maintained.

Do not accelerate to high speeds on tracked snowmobiles. It could lead to an accident.

Converting a tiller into a crawler snowmobile is not difficult, the main thing is to take care of safety.

Homemade snowmobiles from Tiller

Not every tiller is converted into a snowmobile, so before making a purchase of a power unit, pay attention to the following technical features:

• The presence of a rear towing hitch.
• Engine – not lower than the middle class.
• Mandatory manual control.
• Air-cooled motor.

When the power unit is purchased, proceed with its conversion. The main tools and details that will be needed for this make up a small list:

• welding machine;
• pipe bender;
• caterpillars, two wide skis or wheels;
• auxiliary details.

The main thing is to pick up all the details necessary for the transformation. Some of them are self-made. Construction begins with the selection of a snowmobile model. Snowmobiles are divided into two main classes: the wheeled snowmobile and the tracked snowmobile. It is preferable to make a layout.

Wheel travel

If the snow cover in winter in your area is not too high, it is more advisable and economical to give preference to the wheeled option. All you need is a compact trailer and matching wheels. The maneuverability in this case is much higher, since the specific weight of the rear-mounted wheels is relatively low. The installation of special chains will prevent the equipment from slipping in the loose snow cover. There are two ways to make wheels:

• Truck cameras can be used to craft wheels. Lower them and put them on the wheels of the tiller. In the final step, use chains to wind the wheels, fix the ends and only pump them with a pump last..
• Equip the trailer and tiller wheels with metal hoops. One per wheel is sufficient. When choosing the size of the hoop, be guided by the dimensions of the wheel. The width should be 2-3 times larger than that of the wheel, and the diameter should be slightly smaller. Weld some metal plates on the back of the hoop to increase the level of adhesion to the surface and ensure the stability of the unit. The optimum plate thickness is 25 mm. This will create a simulated lug. Before putting on the hoop, be sure to lower the cameras, they will be tightly pressed against it after inflation.

Do-it-yourself snowmobile from a tiller: read in order

Tiller Snowmobile: Various Design Options

Among the varieties of Tiller snowmobiles available today, there are:

• wheeled;
• caterpillar;
• snowmobile skiing.

The wheeled snowmobile has a primitive design. The only element that is replaced are the wheels – instead of them, they put large tires or even low-pressure wheels. They are made all-wheel drive so that the equipment can be turned to the sides without any problems. Among the disadvantages of wheeled snowmobiles from a tiller is suitability only for shallow snowdrifts..

A homemade snowmobile on skis is also considered one of the easiest options for replacing branded snowmobiles. If you take a ready-made sled as a basis, the assembly process is simplified as much as possible. Another method is also possible, when skis are made of plastic on their own..

A tracked snowmobile based on a Tiller engine is considered the most time-consuming to recreate. Given its versatility, excellent cross-country ability and maneuverability, let’s dwell on it in more detail..

Design features

The homemade tiller snowmobile is represented by the key elements in the form of a drive and driven part. The latter consists of runners, steering column and shock absorbers. The driving part should consist of a drive, a frame and a power unit. To have a clear idea of ​​the design of future home-made equipment, select a suitable drawing, taking into account the conditions of further operation, then complete a sketch and make a cardboard layout.

As for the options for operation, they should be thought out in advance, so that when working on a drawing, they should be able to supplement and correct it. So you will have a clear idea of ​​what you can make yourself in the future, and which elements you can get rid of altogether. It remains to decide between wheeled and tracked, both options were discussed in detail above.

Types of homemade snowmobiles

Even without global modifications, you can get a decent all-terrain vehicle by putting snowmobile wheels on the tiller and fixing a small trailer. As for snowmobile wheels, they can be made in the form of tracks or wheels directly.

Самоделки, Изобретения и Удивительная техника 50 / �� Amazing snowmobile compilation

Snowmobile from tiller on tracks

a crawler tiller to convert to a snowmobile is a little more difficult, but possible. Using the tiller motor, you can make a structure with great stability and passability. For this, the frame and transmission are mounted. Make sure the engine has enough power, you need a tiller of at least 6 horsepower. To make a snow motonart with an engine, you need to use:

• reducer;
• fuel tank;
• steering;
• centrifugal clutch.

It is good if you have tracks from other snowmobile machines in your household stock. If not, then don’t give up. It is quite possible to assemble the caterpillars on your own, using improvised tools and materials.

Next, you need to decide on the location of the engine: front or rear. Try to keep the structure as light as possible and keep the ski soft. All this will make it possible to achieve high cross-country ability in deep snow. The principle is as follows: inside the caterpillar, when driving, 4 wheels roll along the conveyor belt. Special soil hooks are attached to the tracks to enhance traction. Caterpillars can be made at your discretion, but you should carefully consider the dimensions.

Wide or too long tracks will unnecessarily stress the engine. This, in turn, will complicate the handling of the snowmobile on tracks in the snow. A track that is too small will not be able to support the weight of the entire structure with the driver. It will become unstable and sink into loose and deep snow. For the manufacture of tracks, the simplest materials are used: plastic or plastic pipe of small diameter, wheels, bearings.

Workpieces with a length of 0.5 cm are made from the pipe, from which ground hooks are obtained. They are attached to the tape at the same distance from each other. Then they are bolted into the holes on the conveyor belt. The frame is made using square pipes or a channel. Use a tie rod without ball ends, as the steering and ski axes lie in the same plane.

On the front of the frame, bushings are attached to allow the skis to turn. They can be made from steel couplings with small diameter nipples and threads. Racks of skis and tie rods are welded to the pipes. To control the snowmobile, corners with a metal undercut are attached to the skis, which will allow you to move on ice or snow crust.

The weight of such a snowmobile is no more than 100 kg, and it is very simple to operate the vehicle. Since the power of the motor is low, the speed does not exceed 10-15 km / h, so no brakes are provided. The end of the movement occurs due to the reset of engine speed or the so-called engine braking.

Self-production

Let’s consider step by step how to make different types of snowmobiles with your own hands.

How to choose an engine

In order to create a snowmobile, it is necessary to consider the most important and central part of the entire mechanism – the motor. The motor must have a decent amount of traction to move the entire machine in tough snowy conditions. To make everything work out as it should, a powerful motor from Tiller Neva will do..

With such an engine, one or two people will be able to move around on a homemade snowmobile from a tiller with their own hands. Engine power has 6-7 horsepower, which is quite enough for driving on snow..

If you add a snowmobile stand to the tiller, the load capacity will increase and you can easily load your tiller for snow rides..

Why is this engine good, many people ask. In fact, there are many more advantages than one might think:

• First of all, this is a democratic cost..
• Good quality is also proven by Japanese production.
• The motor has an additional air cooling system.

Also note that gasoline can be used as fuel..

A do-it-yourself snowmobile from a tiller – the best home-made devices and mechanisms. 110 photos and videos of the construction of a snowmobile

In modern times, few gardeners and gardeners do without a tiller. In warm weather, this technique is very often and densely used in ordinary daily affairs and never stands idle. But in the winter period, it is difficult for a tiller to find an application, and this suggests that the car will simply stand idle..

Home remodeling masters have come up with a use for the tiller and in the cold. I don’t want to move through the snow on my own, especially since in some places the snow reaches impassable volumes.

That is why a snowmobile is made from a tiller for the winter. This is a benefit both for the owner and for the equipment itself, since the tiller does not stand idle.

In the photo of a snowmobile from a tiller made with your own hands, you can clearly see that everyone makes such a model as he wants. For those who decided to create such a useful unit, you will need to choose which option is closer to him.

In this article, we will cover some important points for creating a snowmobile..

Summary of the review:

• How to choose an engine
• Features of the constructive plan
• How to decide on a move option
• Photo of a snowmobile from a tiller with your own hands

Features of the constructive plan

The simplest version of a snowmobile consists of a part that leads and one that is driven first. The second part consists of a seat, shock absorbers, a steering part and runners, thanks to which this part moves. The second part is much more complicated, since it contains all the elements that set the snowmobile in motion..

First of all, in the second part, it is necessary to correctly provide for the power unit, that is, the motor itself. The frame on which everything will be equipped and the drive is also important..

Diagrams and drawings of a snowmobile from a tiller with your own hands must be done in advance, and you can find the desired option on the network or in various kinds of literature.

To begin with, before drawing up a drawing, determine the purpose for which the snowmobile will be used. After the drawings, you will need to select parts, and, if possible, do some with your own hands..

Snowmobile attachment for tiller

A variety of snowmobile solutions for tillers are sold in limited editions. Main advantages over a factory snowmobile

• Low cost
• Compact size for transport and storage
• Fast assembly and disassembly of the structure
• No tiller modifications required
• maintainability

Here is one of the options for such a ready-made set-top box:

Such an all-terrain vehicle will help when transporting goods both on snow and on mud..

And here is a similar option – a prefix to the tiller. The manufacturer produces devices both for specific models and for self-adaptation to any brand and model of the cultivator.

All such a unit is about 40 kg. The maximum speed is up to 20 km / h. Time required for installation – 10-15 minutes.

Video of work as a snowmobile:

Fun Tiller Based Tracked Snowmobile Roller:

Snowmobile from Tiller

The most convenient option is the tiller. This is an almost finished construction for assembling a snowmobile. True, it is worth noting that a motorized cultivator will rather be a motorized towing vehicle, also called a motorized dog, than a full-fledged snowmobile. First of all, due to the low power of the cultivators and low speed. But for transporting goods and yourself, a good option.

Since there are many models of tilers, there is no single universal scheme for building a snowmobile in principle. As a rule, everything is “collective farm” from the available materials with a minimum investment.

And so, consider several models of homemade snowballs collected by the craftsmen of our vast homeland.

Tiller snowmobile without track

This option will require minimal design changes, which will greatly delight when spring comes and the need for sowing..

As a rule, for driving on snow, other wheels of a larger diameter are installed on the cultivator, like those used on caracats. Such wheels do not have a hard tire, because with a large diameter, this greatly increases the weight, and as such there is no need, since when moving on snow, wheel wear is minimal. Therefore, leave the tire, and tighten it with bundles to maintain its shape and improve grip on snow..

An example of such a snowmobile:

In this homemade product, the wheels are tied with chains for greater reliability..

And here is an option with a higher carrying capacity.

Rear platform on skis, large diameter wheels are also installed, the outer part of the wheels is additionally protected: