How the line for the trimmer is inserted into the grass trimmer

How to insert a trimmer line into a grass trimmer

There are some useful tips and recommendations that will be useful to know not only for beginners, but also for the experienced masters of trimmers. These tips will help prevent negative consequences in the form of injury and malfunctioning of the mechanism. These tips state the following:

  • It is necessary to install the cover before clicks. And it is 2 or more clicks, which depends on the number of locks. If one clamp does not snap into place, the reel may jump out when starting the tool and injure a person
  • Do not reel in your trimmer line with too much retraction or more than you can reel it in. It is better not to reel in more fishing line than there is, as this will lead to negative consequences in the form of inability to unwind it when necessary
  • If you own the tool not with two leads of fishing line, but with one (usually these are low-powered units), then the winding process is performed in a similar sequence as described above, only with the difference in the absence of the middle rim between the extreme bases of the spool
  • After changing the material you should preliminarily check the working order of the tool, and only then proceed to mowing. If not checked beforehand, the scaffolding can unravel and injure people

This is interesting! Choose the right quality material so as not to be injured when working with gasoline mowers, trimmers and brushcutters. When mowing grass small stones and other materials fall under the rotating parts and may fly long distances. Therefore, despite the fact that the line for trimmer is not a knife, you should wear special protective outfit when working with the tool.

The result of the work done is the following. after the replacement of the new material the usual one is enough for an area of up to 600 square meters, but taking into account the presence of a reinforcing layer on the line

Conventional nylon materials last less, which is important to consider when working. Do not try to mow thick-stemmed grass with a fishing line, as special metal discs or knives are available for this purpose

Publications

Chainsaw tires. types, selection and replacement

What are trimmers for grass and what is better to choose pros and cons

How to repair chain saw starter motor

Choosing a line

In order for the threading of the line into the trimmer head to be successful, it is important not to miscalculate the choice of consumable material. The thicker the cord you tuck in, the thicker and tougher the grass it can cut. Often a universal line is used for trimmer, the diameter of which is 2 mm. The following methods can help you find the right diameter for your mower:

  • Check the manual provided with your trimmer for information on line thickness.
  • Pay attention to the bobbin itself. Sometimes there is information on the trimmer about the available line diameters.
  • Another option is to try to insert a cord into the outlet hole. If it fits through easily, then the diameter of the line you have chosen is appropriate.
line, trimmer, inserted, grass

Grass trimmer reel

You can choose the cord according to the type of motor. If the line for the trimmer will be too thick, then the resistance to rotation will increase. the engine in this case will overheat a lot and will soon fail. Useful recommendations:

  • For an electric device with an engine less than 500 V, a 1.3 mm thick filament will do. If you can’t find one, you can use 1.6 mm cord for your trimmer. If you have more than 1 kW, choose a cord with a diameter of 2 mm.
  • With gasoline grass trimmers, it matters how the shaft is mowed. For the bent version, a 2 mm cord is often used. If the shaft is straight, install 2.4-2.5 or 3 mm thread. The thickest line for the trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cord cross-section. Some popular options:

  • The most common lines with a circular cross section. They mow fresh grass well, but cope worse with shrubs, dead wood.
  • Twisted (spiral) cord is not very strong, but not bad for thin young grass.
  • A serrated cord with sharp edges is ideal for large weeds in a neglected area.
  • You can mow the lawn more evenly with a rectangular, star or square grass trimmer line, but they are not very durable.
  • The strongest is two-piece cord with an inner core and a round section.

Grass trimmer line types

Note that you can’t use wire, metal cords and ropes, or ordinary fishing line instead of fishing line. The device will be hazardous to both the user and others. So the rope or similar products will gradually start to work together, resulting in their ends unraveling, and the small pieces will fly apart at high speed.

Removing and disassembling the coil

The mowing trimmer head consists of a casing, a spring (not in every model), a bobbin with cord, a cover. Be sure to unplug the grass trimmer before proceeding to disassemble the reel of the electric unit. Disassembly method depends on how the mowing head is attached. First option:

  • To remove the cover that covers the inside of the head, press in on the latches (catches) located on both sides of the head.
  • Remove the cover, under which you will see the bobbin. remove it from the body. Some trimmers have a spring under the bobbin, which should also be carefully removed.
  • After removing the bobbin, you will see a screw in the center of the housing. Unscrew it with a screwdriver.
  • After removing the fasteners, take the body of the part and, rocking it in different directions, remove the reducer from the shaft.

In the second version, the grass trimmer head is screwed onto the gear shaft. To remove it, you need to fix the shaft. For this purpose, such devices have a hole through which a thin screwdriver or metal rod is inserted. A brief instruction:

Soaking Your Trimmer Line to Make it Last Longer

  • Insert a screwdriver in the opening and lock the shaft.
  • Grasp the body of the head and start twisting it. This should be done in a clockwise direction, t. к. the thread on the shaft is left.

Winding the line on the spool

Preliminary preparation

First of all, to wind the fishing line requires removing the spool (bobbin, bobbin) from the grass trimmer. specific actions will depend on the complexity of the configuration and type of the product itself:

  • small electric grass trimmers with a working arrangement of the motor and spool in the bottom usually have side keys on both sides of the bobbin. When pressed simultaneously, the upper part of the spool, along with the internal contents for winding the fishing line, detaches, while the lower part remains on the trimmer. Disassembly of the bobbin should preferably be done on a flat, smooth place, so that the included spring does not pop out and get lost;
  • Electric and gasoline grass trimmers with a curved boom without the possibility of installing a knife, as a rule, have a spool with a special wing nut: in such designs, one hand should hold the bobbin in a fixed position, and the other counterclockwise rotate the fixing reel on the boom nut wing nut. After loosening the nut the entire bobbin is removed.
  • electric and gasoline grass trimmers with the possibility of installing a blade on a straight shaft (e.g. STIHL grass trimmers) have a hole under the reel. To immobilize the rod, a screwdriver or other suitable object is inserted into this hole and a slow rotation is achieved in such a mutual arrangement that the screwdriver enters the hole and the bobbin is fixed. After that the spool body is twisted clockwise (with the left thread) and removed from the grass trimmer.

For the second and third cases, depending on the design, the reels are disassembled in different ways. In spools with a drum unscrew the drum, in spools with latches the latches are pressed and one part of the spool is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them with your hands in opposite directions until they are completely unscrewed.

How to tuck the trimmer line into the grass trimmer: some simple tips

Thanks to modern power tools, a person has many opportunities to reduce manual labor. Such innovations include the grass trimmer, which greatly facilitates the process of mowing the grass and taking care of the lawn. This accessory reduces the time spent on gardening jobs, turning hard physical work into fun. A line for a trimmer is used as a cutting tool. It is highly tensioned and thus mows grass at almost any height. Controlling a power tool is quite easy, but the problem arises when the cutting material runs out. Not everyone immediately understands how to insert a line into a grass trimmer. Although this is a simple operation, but a person who encounters this task for the first time, it is not always clear how to properly wind it on the spool. over, the manual sometimes does not contain information on how to choose and replace the trimmer line for the trimmer.

When you figure out how to change the cutting material, further use and maintenance of the electric trimmer will be greatly simplified. To wind the line for the grass trimmer trimmer, you should perform several operations, namely:

  • Unscrew the head by turning the drum to the right side. You will have in your hands the head with the remains of the old thread. Open it with a screwdriver or squeeze the catch and twist the cover in the direction of the arrow. Carry out this operation should be careful, since there is a spring inside, which, straightening, can throw out all the internal parts of the drum. To change the line for the trimmer in the trimmer, you need to take out the spool and remove the remaining material.
  • Take 5 meters of new filament and fold it in half. In the middle of the spool there is a hole in which to insert the material. There’s also an arrow there to indicate the direction to wind the line for the grass trimmer. It is important to take into account some points. If the spool has two holes, then half of the line for the grass trimmer should be tucked in one direction, and the other. in the opposite direction. When finishing inserting the material, it is better to leave 15-20 cm free.
  • Assemble the reel, put the spring and washers in place. After that, holding the spool, tuck the ends of the line into the holes on the sides of the nozzle. Then put the head back in place, pulling the cutting material.

As a rule, it is necessary to change the line for the trimmer in the trimmer once for the whole season. However, if the mowing area and grass height are large, you will have to install this consumable more often. If you need to tuck the line for the trimmer in the trimmer for grass TM “Makita” or other manufacturer, you can buy it in the online store “Toolparts”.

line, trimmer, inserted, grass

Adjusting the thread

If the mowing performance decreases, the thread must be readjusted. The filament length can be optimally adjusted at any time during mowing by lightly touching (arrowing) the filament head to the floor. However, this is only possible if the thread peeks out min. to 3 cm.

line, trimmer, inserted, grass

Thread cutter (see “Thread Cutter”). pp. 8, D/8) automatically cuts too long thread ends If the thread ends are shorter than 3 cm, the length must be adjusted manually To do so, press the button and pull firmly on the thread. WARNING: Cleaning the thread head, changing the thread and manually adjusting the thread length may only be performed when the motor is off and the mains plug is unplugged!

Winding the line

Threading the line into the grass trimmer reel is a relatively simple procedure if you follow a certain algorithm. When you need to determine how many meters of consumable material is enough, wind it on the bobbin so that the coil does not exceed the diameter of the sides. Once you have decided on the length of the cord, follow these instructions:

  • Fold the filament in half so that one end of the line is 10 to 15 cm longer than the other.
  • Start charging from the center rim, which divides the grass trimmer bobbin into two parts. Find the groove where the cord should be inserted. Bend the last one in half.
  • Determine which direction you want to wind the line for your trimmer. To do this, look closely at the bobbin, which may have an arrow or inscription. This indicates the winding direction. If there is no marking on the bobbin, look for an arrow on the mowing head. wind it in the opposite direction.
  • Wash the consumable material carefully, coil by coil. Try to keep the thread as tight as possible.
  • After you finish laying the cord, secure the short end of the material first. To do this, insert it into the groove on the side of the spool that fits the diameter. Attach the second end (longer), in the groove on the other side of the grass trimmer’s bobbin.
  • After securing the line for the trimmer, cut the ends. Remember to leave a seam allowance of about 10 cm.
  • Install the tucked-in spool to the mowing head of the unit. To do this, take turns inserting and pulling the thread into the output holes of the head, and then place the bobbin of the device into the skin.
  • With the required force, pull the cord out of the fixing grooves and tighten the material. When you have finished, put on the cover and fasten it with the latches.

Winding the fishing line on the spool, step by step

You can wind the cord on the grass trimmer in another way, which charges two pieces of material instead of one. The replacement is done as follows

  • Bend one end of the cord into a hook shape.
  • At the bottom of the bobbin, there should be a hole designed to hold the fishing line in place. Insert the bent end of the thread there.
  • Wind the cord material in the direction of the arrow up to the desired level, which does not exceed the diameter of the grass trimmer spool.
  • Repeat the same for the second of the bobbin.
  • Assembling the head of the device is similar to the first method.

Getting ready. remove and disassemble the bobbin

Most electric and gasoline powered trimmers require that you remove the bobbin to change the line. FUBAG tools (electric trimmers and petrol trimmers) allow you to skip this step. To make the instructions universal, we will still look at it in detail:

Fix the shaft. Insert the locking bar in the bobbin hole. It can be a thin screwdriver or a metal bar.

Unscrew the bobbin case. In this example, strictly clockwise.

Unscrew the cover according to the direction shown on the housing.

The preparatory step is complete. You can wind the line.

Step-by-step instructions on how to wind the line for trimmer on the grass trimmer spool

With the advent of spring you often spend your time in the cottage or homestead. Grass trimmer will protect you from such problems as grass and weeds. This tool easily trims and mows the grass in difficult areas, where an ordinary lawnmower can not do it. trimmer for grass. A very effective and handy tool for mowing grass along fences, flower beds, houses and rows in the garden. Several types of garden trimmer for grass (gasoline, electric and battery-powered) have been invented. It would seem that everything is fine, in your arsenal has

You may have such a wonderful helper, but over time the cutting element wears out and it becomes necessary to replace the run out of fishing line. And how to tuck the line for the trimmer in the trimmer for grass, not everyone knows. We suggest using the step by step instructions with pictures attached.

Instructions on how to wind the line for the trimmer on the grass trimmer spool

Replacing a Weed Eater String (String Trimmer Line) | The Home Depot

  • 1. First we need to disassemble the grass trimmer head. Press the latch on the body of the product and turn the cover clockwise. Remove the bobbin.
  • Now we have to figure out how to wind the line for the trimmer on the grass trimmer spool. Measure about 6 to 7 m of line and put the end of the line through the hole in the bobbin.
  • Wind the line on both sides of the trimmer. The winding direction is always shown on the bobbin as an arrow.
  • Leave the ends of the cutting element 15 cm long free. Do not wind too much fishing line. Leave 6 mm between the outer edge of the bobbin and the line.
  • Insert the remaining two ends of the fishing line into the opposite holes of the bobbin.

In this article we have learned how to wind the line on the grass trimmer spool. And if you have done everything correctly, when you press and hold the bobbin, it should pull out again. line for trimmer for grass trimmer. this is a very important element, without it the tool loses its function. This is essentially the heart of the grass trimmer. That’s why you should buy at a specialized gardening equipment store and approach the choice with special care. When buying a new line for the trimmer, be sure to compare it to a piece of the old used cutting element.