How to wind the line for trimmer on the trimmer for grass
The thickness of the cord must fit the parameters of the selected tool. Too thick a trimmer line will entangle the thread on the reel, contribute to motor overheating and wear out the bushings quickly.
According to the thickness of the line for the trimmer is conditionally divided into several types:
- Within 1.2 to 1.6 millimeters. Suitable for models with a capacity of up to 0.5 kW. Often these are electric grass trimmers;
- From 2 mm to 2.4 mm. This size is the most popular, because it copes with young and tough grass. It is installed on tools with a power of about 1 kW;
- 3 mm to 3.2 mm. Suitable for gasoline-powered units that will mow thick weed stems;
- Court 4 mm. Handles overgrown areas.
To determine what kind of line for the trimmer is suitable for the scythe, you can use one of the ways:
- The thickness of the cord should be specified in the user’s manual;
- Manufacturers often put important data on the bobbin, including the allowable diameter;
- Slide the trimmer line through the exit hole. It should run smoothly.
The shape of the section is also paid attention to, because the thread does not cut, but interrupts the grass stem. Types of cords according to the shape of the section:
- Round. Universal option, which allows you to cut fresh and dry vegetation;
- Multifaceted with 3 to 6 facets. You can mow stiff and thick stems. But the consumption of such a material is quite large, so it is suitable only for specific purposes;
- Shaped. It has a star shape or square with notches. The former is used for cutting fresh vegetation.
Grass trimmer line for grass trimmers are made of different materials:
- A polyamide or polypropylene nylon trimmer line is best suited for brushcutters. Inexpensive versions with polyethylene in the composition. They are not resistant to loads, cannot withstand frequent temperature changes. Polypropylene line for the trimmer will last longer if you soak it in water for half an hour beforehand;
- The strongest are considered strings with aluminum particles and a diameter of about 4 millimeters.
Do not use metal wires or ropes, which can damage the tool.
Proceeding from the described parameters, you can choose the optimal line for the trimmer for the care of lawns.
How to wind the line for the trimmer on the brushcutter spool: method 1
Before you start winding, you need to open the trimmer head.
First, the amount of fishing line to be wound on the bobbin is determined. The coil must not protrude over the edges, otherwise the spool will not fit into the casing.
After determining the length of the line, you can proceed to its threading in the bobbin:
The line for the trimmer is folded in half, one edge is left longer by 10-15 centimeters. The bobbin is divided in two by the center bead. It has a slot on it for the court, which must be bent in half
You will need force to wind it; the direction of winding is important. There should be an arrow or inscription on the bobbin indicating the winding side
If there is no indicator, there must be an arrow on the head of the mower. The cord is wound to the opposite side; Wind the line for the trimmer as carefully as possible, the thread should be as taut as possible; After completing the laying, the short end of the thread is fixed, it is inserted into the appropriate diameter groove on the side of the spool. The long edge is fastened on the opposite side; With the thread fastened the edges should be cut with a gap of about 10 centimeters; The tucked spool is installed in the mowing head. The edges of the thread are pulled up from the fixing grooves; The cover is put on and secured with latches. It should be fully locked in place.
How to tuck a trimmer line into a grass trimmer reel: the second way
Some spools can be wound differently. Two lengths of thread are loaded, not one folded in half.
- As in the first case, the length of the new thread is determined;
- One edge of the court is bent with a hook;
- At the bottom of the bobbin there are holes for fixing the fishing line, where the bent edge of the thread is inserted;
- The thread is wound behind the arrow on the spool. The level of winding should not exceed the diameter of the bobbin;
- The same is done with the second cell of the bobbin;
- The edges of the fishing line, which stick out of the holes, must be cut. You can simply turn on the scythe, while rotating them a knife will cut them. The trimmer line is cut by hand with scissors if the diameter of the court is too large.
Features of trimmers
Such a convenient, and most importantly, effective device as a trimmer for grass, there are several variations:
As is clear from the names, the types of grass trimmer noticeably differ from one another. But regardless of the type of this tool, its cutting element may be a trimmer line. Of course, the line set in the grass trimmer reel is not endless. And sooner or later it will be necessary to replace it with a new one.
Consumption of fishing line directly depends on how often you use the device and the amount of work performed. The more grass is cut and the more often it is trimmed with the grass trimmer, the more the trimmer line is used. And consequently, the faster it will run out. This raises the question: how to tuck the line for the trimmer into the grass trimmer reel?
Not everyone knows the answer to this question. But the line winding on the reel plays an important role in the grass trimmer
It is very important to wind up the new line correctly on the trimmer reel for the device to function properly. About how to change the line for the trimmer on the trimmer, and will be discussed in this article
Choosing line for your trimmer
trimmer fishing line must be strong, stiff and flexible. in a trimmer it serves as a working tool for cutting the grass. The lines are manufactured in different thicknesses. from 1,2 mm to 4,0 mm. Most models are designed for a maximum thread thickness of 3 mm. Which diameter of grass trimmer line is best for your application depends on several factors.
Depending on the hardness of the mowed vegetation:
Important: if the filament is too thin, it accelerates engine wear and it is too coarse, so it overheats and breaks down prematurely.
The cord structure of the line is important:
- round. universal, the strongest for coarse grass;
- shaped. for soft plants;
- curled and notched. for long, thin stems.
Important! Choose lines for your trimmer in the style and specifications recommended by the brushcutter manufacturer. Such material will work long and well with optimal loads on the product’s motor.
How to change a trimmer line on a trimmer
The line for the trimmer is wound on a spool (bobbin), which is located in the body of the trimmer head for grass. First unscrew the head from the brushcutter bar and open its top cover by pressing on the side latches. In some models the body simply unscrews.
Take out the spool, clean it from dirt and old fishing line. Coils come in one- and two-sectional.
Winding a line on a single reel
Take 2 m of fishing line, thread it halfway through a special hole inside the spool. On both sides of the hole there are equally long fishing line ends sticking out. Wind them both on the groove of the spool in the direction indicated by the arrow on the body (the reverse rotation of the spool on the shaft of the grass trimmer). Do not reel the line for the trimmer to the end. the 10-15 cm pieces that will be working, fix them in the slots on the side of the reel. Locking is needed to ensure that the line for the trimmer does not unwind when you install it in the head of the grass trimmer.
We insert the reel into the head housing, at the same time we put the free ends of the line through the holes in the housing, put it out. Assemble the head, put it on the grass trimmer. That’s it, the line change in the trimmer is done.
How to wind the line for the trimmer on the grass trimmer with a two-section reel
If the spool has two sections, the line for the trimmer fold in half and place the bend in a special groove in the edge between the sections. Start winding the ends each in its own groove. then everything is the same as in the case of a one-section reel.
How much fishing line to wind on the grass trimmer? You can reel 2-4 m, depending on the model of the product. In each case it should not be wound too tightly, the thread should have a free stroke for pulling in the course of work.
How to change a line for a trimmer on a knife
For mowing hard last year’s grass and bushes it is recommended to replace the line for the trimmer with a knife head. The mowing head can be made either as a solid metal plate with several cutting blades (usually two to four blades) or as a disc with plastic blades loosely coupled to it. All-metal nozzles are recommended for experienced mowers on the right tool, as they can potentially cause very serious injury. They are recommended to be put only on trimmers with a straight boom (so that the nozzle is as far away from feet as possible all the time) and on trimmers for grass with a paired U-shaped handlebar resembling a bicycle or motorcycle handlebars (perhaps that is why such petrol trimmers are often called brushcutters). Grass trimmers with a D-handle and a curved boom are recommended only with a disc with plastic blades, which are much safer.
Bosch grass trimmer
Installing the disc is done in roughly the same sequence as installing the trimmer head. The metal blade is mounted on a support washer of appropriate diameter so that the disc locks tightly without play. The top of the disk is closed with one or two fixing washers, which are screwed to the gear shaft with a nut with a left-hand thread. Be careful not to lose the nut when you remove it, as you can’t buy it at a hardware store, but at a professional trimmer repair shop or service center. The plastic blade nozzle is screwed on the gear shaft in the same way as the line head.
Don’t forget to wear safety glasses, earphones and good, durable shoes.
When working with an electric line trimmer, be careful not to accidentally get under the line for the trimmer cable, which the technique is connected to the mains.
The electric grass trimmer is best selected in a battery version. Of course, the batteries should be periodically charged, but this design is much safer, since there is no contact with the electric network of 220 V. A spare battery is advisable, of course, so you can change it at any time.
We suggest you watch a video on how to change the line for the trimmer on the head of the lawnmower.
Winding the line
Threading a fishing line into the grass trimmer reel is a relatively simple procedure, provided you follow a certain algorithm of actions. When you need to determine how many meters of consumable material are enough, wind it on the bobbin so that the coil does not exceed the diameter of the sides. Once you have determined the cord length, follow these instructions:
- Fold the consumable material in half, so that one end of the fishing line is 10-15 cm longer than the other.
- Charging must begin with the center curb, which divides the grass trimmer bobbin into 2 parts. Find the groove where the cord should be inserted. Bend the last one in half.
- Determine which direction to wind the line for the trimmer. To do this, look closely at the bobbin, which may have an arrow or inscription on it. It indicates the winding side. If there are no markings on the reel, look at the arrow on the mowing head. wind it in the opposite direction.
- Wash the consumable material carefully, coil by coil. Try to keep the line as taut as possible.
- After completing the cord strap, first clamp the short end of the material. To do this, insert it into the groove on the side of the spool that fits the diameter. Attach the second end (longer), in the groove on the other side of the grass trimmer’s bobbin.
- After securing the trimmer line, cut the ends. Do not forget to leave a seam allowance of about 10 cm.
- Position the threaded reel on top of the mowing head. To do this, take turns inserting and pulling the thread into the output holes of the head to then place the device’s bobbin into the skin.
- Pull the cord out of the securing grooves with the required force and tighten the material. When you have finished this action, put on the cover and secure it with the latches.
Winding the cord on the grass trimmer can also be done in another way, in which two pieces of material are charged instead of one. The replacement is done as follows:
- Bend one end of the cord in the form of a hook.
- There should be a hole at the bottom of the bobbin that is designed to hold the fishing line in place. Insert the bent end of the thread there.
- Wind the cord material in the direction of the arrow to the desired level, which is no larger than the diameter of the grass trimmer spool.
- Do the same for the second cell of the bobbin.
- Assembling the head of the device is similar to the first method.
How to remove the spool from the grass trimmer?
To change or wind the filament on the spool, you need to remove it.
The complexity of its removal depends on the model of the tool:
- Low-mounted tool. The motor here is almost at the ground. To remove the spool, press the buttons on the side of the grass trimmer. After pressing these buttons, the body opens, where the spool with the fishing line is located.
- Grass trimmer with bent rod. Here it is necessary to turn the special thumbscrew counterclockwise. After that, the spool and the spring in it are removed.
- Straight bar tool. The rod is held stationary with a screwdriver or other object. Turn it clockwise to remove it. Then take the tool apart and remove the bobbin.
- If a single strand tool is used, about four meters of thread will be needed. This thread is passed into the hole inside the spool, where it can be clamped. Then one end of the line is directed in the direction of the arrow. The end of this thread is then clipped into the groove in the bobbin. This is to prevent the thread from unwinding when assembling the spool. If there are no slots, hold the trimmer line with your hand and reassemble the bobbin.
- If a twin-twist tool is used, first check the number of grooves that are present.If there is one groove, the two tendrils will be directed into one groove. If there are two grooves, then each tendril will be directed into its own groove.
In the first case, the desired amount of cutting thread is passed through the hole so that the result is a thread of equal length. Then you need to twist the bobbin on the arrow. After that, begin to assemble the tool, holding the thread with your finger.
If the reel is equipped with a semi-automatic mechanism, then wind the line for the trimmer as follows:
- The thread is threaded through the hole that is inside;
- Secure the ends of the thread in the grooves on the body.
- The reel is assembled and a special button is pressed;
- After which the line for the trimmer itself begins to coil in the desired direction.
It should always be remembered that the cutting line must be protected from hard things. This will extend its life.
If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread for a new one.
How to tuck the line for the trimmer into the grass trimmer reel
To replace the fishing line in the trimmer, cut a piece of material of the right size by folding it in half. One of the halves should be 5-10 cm longer than the other.
To wind the line correctly for the trimmer on the reel, the middle of the line, folded in a loop, must be placed in the groove of the central divider. One half of the fishing line is wound tightly onto the upper part and the other half onto the lower part. The longer part is wound onto the lower part. Wind it in the opposite direction to the direction of rotation of the head. On the lid or side of the head an arrow should be drawn. it shows the direction of rotation. The fishing line should be wound in the opposite direction to the arrow. Do the work carefully, firmly pressing the coil to the coil.
Insert the remaining ends, 10-15 cm long, in the slots on the top edge of the spool, this will secure them. With the ends fastened the spool will not unwind.
If you do not have the right length of line, you can wind the line in two pieces instead of one. In this case, bend the end of the fishing line with a hook and insert it into the slot of the central partition of the bobbin. Do the same with the second piece. Now wind first one piece and then the other on their halves of the spool against its direction of rotation.
To tuck the trimmer line into the grass trimmer, insert the ends into the holes in the mowing head and pull them out. Put the spool on the axle and push it down so that it sits in place, then pull the ends of the cutting line again to pull them out to their full length.
The outer ends should reach almost up to the protective cap. Cut off the excess. To do this, use the steel plate installed on the housing, which acts as a knife and automatically cuts the line for the trimmer of excessive length when unwinding the mowing head.
The bobbin is closed with a protective cover. Push it in place and push it down until the catches click into the grooves. Always make sure that the cover is properly engaged in the grass trimmer and that the latches are properly engaged, otherwise it might come off during work. In this case the reel will be ejected by the rotational force.
Do not try to reel in as much material as possible, otherwise the reel may not fit and there will be problems fixing the cover. It is better if the spool is filled with thread so that it does not go beyond the dimensions of the part.
Besides mechanical two-blade scythes, there are also single-blade models. What makes them different is that the cutting filament only comes out on one side. Reel in such kinds of scythes may have no central partition, instead of it a slot in the lower flange is used for setting the nonworking end of the thread, and in the upper flange there is also a slot for fixing the working end.
With a replaced fishing line you can start working. Do not mow through thick weeds or brush twigs. this is not a job for a grass mower. To avoid injury and line breakage, make sure no rocks or branches get under the scythe.
For mowing lawns, one filling of a spool of reinforced fishing line is enough for an area of 400-600 m2.
After the cutting line has worn down as a result of the work, turn off the mower and remove the cover on the mowing head. Pull the line out of the slot by pulling it to the correct length, and reinsert it in the slot. The amount of material wound on the reel is enough for 5-10 cycles depending on the model. When you will install the cover in place, look carefully to see if the grooves where the retainers are inserted are clogged, if they are clogged, carefully clean them.
When the trimmer line wears out, you need to disassemble the mowing head again, pull out the spool and rewind the working trimmer line on it.
How to tuck the trimmer line into the grass trimmer spool
To replace the line in the trimmer, cut a piece of material of the right size by folding it in half. One half should be 5-10 cm longer than the other.
To properly wind the line for the trimmer on the reel, the middle of the thread, folded in a loop, must be placed in the groove of the central partition. One half of the fishing line is wrapped tightly around the top of the piece, the other half is wrapped tightly around the bottom. The longer part is wound onto the lower part. Wind it in the opposite direction to the direction of rotation of the head. There should be an arrow on the cover or on the side of the head to show the direction of rotation. The fishing line must be wound in the opposite direction to the arrow. Do the work carefully, firmly pressing the coil to the coil.
Insert the remaining 10-15cm of line in the slots on the top edge of the spool to lock it in place. With the ends fastened, the bobbin will not unwind.
If you don’t have enough line of the right length, you can reel in two pieces instead of one. In this case, bend the end of the fishing line with a hook and insert it into the slot in the center divider of the bobbin. Do the same with the second piece. Now wind first one piece and then the other on your halves of the spool against its direction of rotation.
To tuck the line into the grass trimmer, insert the line ends into the holes in the mowing head and pull them out. Put the spool on the axle and push down so that it sits in place and pull again on the ends of the cutting line to pull it out to its full length.
The extruded ends should extend all the way to the blade guard. Cut off any excess. Use the steel plate on the guard to cut off unnecessary line lengths when unwinding the trimmer head.
The bobbin must be closed with the protective cover. Put it in place and press it down until it clicks into the grooves. Always check that the cover is on the grass trimmer and that the latches are engaged, otherwise it could come off during operation. This will cause the spool to be ejected by the rotational force.
Do not try to wrap as much material as possible, otherwise the spool may not fit in place and there will be problems with fitting and securing the cover. It is best to fill the spool so that it does not extend beyond the part’s dimensions.
In addition to mechanical mowers with two blades, there are also models with one. They differ in that the cutting filament comes out only from one side. The reel in these types of mowers may not have a central partition, instead a slot in the lower flange is used to install the nonworking end of the thread, the upper flange also has a slot to fix the working end.
With the replaced line in place, you can start working. Don’t mow thick weeds and bush twigs. it’s not a job for a lawn mower. To avoid injury and line breakage, do not let stones and branches get under the mower.
For lawn mowing, one filling of a spool of reinforced line is enough for an area of 400-600 m2.
After the cutting line has worn out as a result of the work, turn off the scythe and remove the cover on the mowing head. Pull the fishing line out of the slots, pulling it out to the desired length, and reinsert it into the slots. The amount of material wound on the spool is enough for 5-10 cycles of work, depending on the model of the device. When you install the cover in place, look carefully whether the grooves where the clips are inserted are not clogged, if they are clogged, then carefully clean them.
When the trimmer line is worn out, you need to disassemble the mowing head again, pull out the spool and rewind the working trimmer line on it.
Algorithm of winding line
The order of winding the line depends on the type of spool. with one or two tendrils, as well as with automatic cord charging.
On a spool with one strand
It’s very easy to wind on a spool with a single bar. In such designs, depending on the brand trimmer for grass, fits from two to five meters of cord. The edge of the line in the bobbin must be tucked into a special hole or groove, then the string is reeled in the opposite direction to the rotation of the spool during operation.
Tip! To understand which way to wind the thread, you should look at the body of the bobbin. usually on it are made marks indicating the direction of movement of the spool when working.
After the line for the trimmer is wound, you need to leave a small piece (15-30 cm), put it through the bobbin outlet and reassemble the head.
On a spool with two tendrils
With this type of bobbin you need to look on the inside of the spool to see how many grooves are there for spooling the cord.
Important! If there is one groove in the spool, both whiskers must be wound in a common groove, if there are two, then in separate tracks.
For winding you need to take a piece of fishing line length of two to three meters. For bobbins with a single groove, you should tuck the line for the trimmer into the through hole, align the whiskers, align and wind it on the spool in the opposite direction of its rotation during operation. If you have a fixing groove, place the ends of the filament in it, then pull them out into the exit hole, then close the spool and put it back in place.
For twin-twist spools, the difference is that the string section must be folded in half. Next, it is necessary to charge the middle of the bend in the groove between the grooves, and then wrap each of the pieces of line on its track, fix the tendrils and assemble the spool in the same way as the bobbin with a single track.
On the trimmer head with automatic threading
For automatic threading heads, all you need to do is to wind and pinch the edges of the line, and the tool will wind the line by itself when it’s turned on. It is impossible to make a mistake here, because the coil itself recognizes how the tendrils should be positioned.
To recap! The advantages of trimmers with this head include the convenience of laying the cord, while the disadvantages are expensive and difficult to repair.
How the line head works on the brushcutter why you need to know the principle of operation
Depending on the manufacturer, heads differ structurally not only externally, but also internally. most reels have a compression spring inside (semi-automatic and automatic). Above is the instruction on how to disassemble the grass trimmer head without the spring, i.e.е. on the manual-type head. The principle of disassembling a semi-automatic head with a spring inside is almost identical to the above instruction.
The principle of operation of a semi-automatic grass trimmer reel is as follows:
- Inside the head there is a spool, which is seated on slits that prevent it from moving freely
- The spool is acted upon by a spring which presses it against the slits in the design of the cover
- A line for the trimmer is wound on the tip, the length of which depends on the tool itself. It is usually about 1 to 4 meters long
- During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum is pressed, by which it comes out of engagement with the slots. At the same time the line for the trimmer is coiled from the drum, increasing in length
- After letting go of the necessary amount of fishing line, release the hold-down, and continue mowing
The advantage of a tool with a fishing line is that this consumable does not require sharpening, compared to metal discs. over, if a stone or wood get in the way, the line for the trimmer simply comes off, without negatively affecting the gearbox and the engine of the tool, as it happens in the case of metal cutting blades.
Knowing the construction and design of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the fishing line into the grass trimmer reel. After all, this is the point at which most owners of special tools cause difficulties.
Block: 4/8 | Number of characters: 1782
Winding a line on a grass trimmer
Gradual and accurate disassembly of the bobbin from the grasshopper reel allows you to proceed directly to winding the fishing line. The design features of the head, the number and location of fixing holes dictate the sequence of actions when performing this operation, as well as determine the methods used. Today there are several varieties of spools, depending on the number of fishing line tendrils and methods of threading:
Grass trimmer reel with one tendril
Many owners and experts note the ease of operation and threading of the reel with a single tendril. Depending on the manufacturer, the length of line to be threaded can vary from 2 to 5 meters. In the head, the end of the line is inserted into a special technological groove or hole, and winding is performed in the opposite direction to the working rotation of the bobbin. Most reels have arrow markings on the outside of the housing that indicate the direction of travel of the grass trimmer reel.
After winding you need to leave the free end 15-30 cm to strengthen the centrifugal force, which is decisive in the extraction of trimmer line in automatic and semi-automatic spools. put the left end through the working hole of the spool and make the head assembly.
Trimmer head with two tendrils
After removing the bobbin from the body of the spool, determine the number of spooling thread thread grooves (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if you carelessly spool in the paired groove, there will be problems with operation. Due to the possibility of intertwining of neighboring lines of the tool, a situation may arise where once the working tendrils are worn out, it is impossible to retrieve new ones.
Regardless of the number of spools, trimmer line length of 1 or more must be used.5 to 3 meters. Winding must be done in reverse rotation of the head, because backwards winding will cause trimmer line not to come out of the bobbin. After the line for the trimmer is tucked into the grass trimmer reel, the loose ends (15-30 cm) are threaded into the special holes. Then you assemble the grass trimmer head in the reverse order of disassembly and check its functionality. Do not worry if the ends of the two tendrils are very different in size, because when you start the grass trimmer the blade mounted on the protection will cut off the excess.
Grass trimmer head with automatic line threading
Some models on the market feature a spool with an automatic winding mechanism. The owner only needs to correctly tuck and lock the ends in the head, and the winding operation will be performed by the tool itself when turning on the work mode. It is almost impossible to wind the line wrongly in the grass trimmer with such a head, as the spool itself determines the position of the tendrils. The advantages of the automatic grass trimmer head include the ease of filling the line, and the disadvantages. frequent breakdowns of the mechanism due to the complexity of design and high cost.
Block: 3/3 | characters: 3075
Tips
Working with equipment like a weed trimmer requires care and attention. The implementation of safety measures during work is mandatory for beginners and experienced craftsmen. It happens so that self-confident trimmers lose their guard, make irreparable mistakes and get seriously injured. This is why it is important when working with a machine
- Close the reel cover with all latches.
- Do not coil more line than necessary: it will be hard to unwind later.
- After having reeled in the line, always check that the tool works correctly before mowing.
- Choose quality material that is compatible with your trimmer.
Do not try to mow coarse grass with thick stems with a fishing line. Steel discs are available for this purpose. Wear protective clothing only. Wear safety glasses and proper footwear.
Coiling up the line
Unhurriedly completed disassembly of the spool without losing any of its parts allows you to proceed to the main task. winding up the line in the spool. Technological features of the bobbin design and the number of working tendrils determine the sequence of actions.
A spool with one operating tendril
The simplest variant and uncomplicated sequence of actions:
- Bobbin size and length of the original factory bobbin winding determine the recommended length of line for winding. 25 m.
- One end of line is inserted to the fixing technological opening in the bobbin.
- The line for the trimmer is wound on the reel in the opposite direction to the rotation of the bobbin on the trimmer product. as a rule, on the inside of the reel there is an arrow indicating in what direction the winding is done.
- Smaller part of line is left free for taking it outside. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
- The leftover end of the line goes through the hole in the outer part of the spool.
- The halves of the bobbin are assembled and put on the trimmer rod.
Reel with two working tendrils
In this type of bobbins should determine the number of grooves for winding the line lying on the inside of the spool:
For both cases, take a line for the trimmer with a length of 2-3 m. In single-cable spools the line for the trimmer is pulled through the through hole, its ends (tendrils) are put together and aligned, and then wound in the opposite direction to the bobbin rotation on the rod. the arrow inside usually indicates the correct winding direction. If there are fixing grooves the ends of the line are slipped into them or held by fingers of free hand, put into through hole of outer half of bobbin, bobbin is closed and fastened to the rod of trimmer product.
The difference of winding the line in double reels is that initially a piece of line 2-5 m long is folded in half (to determine the middle fold), and the loop of the fold is inserted into a special groove between the grooves. Both line tendrils are wound each on their own groove, fixing the tendrils and reel assembly is similar to the above version with one groove.
Performing this procedure for the first time may seem lengthy and quite time consuming, but with time and experience this task will be much faster and easier.
The video below will clearly show you how to tuck the trimmer line into the grass trimmer spool and wind it correctly. this operation is nothing complicated and with some patience is sure to succeed:
Once the filament has worn out, turn the mower off and remove the cover on the mowing head. Pull the fishing line out of the slot by pulling it to the desired length, and reinsert it into the slots. The amount of material wound on the spool is enough for 5-10 cycles of work, depending on the model of the device. When you put the cover back on, look carefully to see if the grooves where the clamps are inserted are clogged, if they are, carefully clean them.
When the line for the trimmer wears out, you need to disassemble the mowing head again, pull out the spool and rewind the working line for the trimmer.
grass trimmer is the most common unit used for cutting grass and small bushes. This machine is notable for its ease of maintenance, uncomplicated operation during work, and thanks to its low weight even women cope with it. It is no secret that for qualitative performance of works on grass mowing, the correct selection of cutting tools is required. As the latter, trimmers use special cutting attachments (discs, knives) or trimmer heads with fishing line inside. Trimmer nozzles and fishing line are consumable tools, but if the blades can be sharpened, then when the line is used up, it is necessary to replace it. In this article, we will tell you in maximum detail how to properly replace the line for the trimmer.
How to remove the spool and replace the line for your trimmer
Owners trimmers, mostly beginners, come into confusion, bordering on panic, when there is a need to change the cutting tools or line for trimmer in the coil. Very often when users try to unscrew the mowing head they simply cause it to fail, not realizing that it unscrews in the opposite direction. To prevent this from happening if tool replacement is required, it is recommended that you read the step-by-step instructions below.
- Before you put the line for trimmer on the spool, turn off the brushcutter engine or de-energize the electric grass trimmer to avoid injuries that may occur if the cutting attachment accidentally starts rotating.
- Unscrew the head attached to the gearbox shaft. To do this, the shaft must be secured by aligning the holes on the washer and on the axle, and inserting a metal bar or screwdriver into them.