How to wind line around the reel of the champion grass trimmer • CIMFLOK.COM

How to wind the line onto the reel of the Champion grass trimmer

We have described how to wind the line into the reel of a double-barbed grass trimmer. This is the most common option. But there are other ways as well. Position the spool so that the ends of the line can be pulled into the outlets of the trimmer head. The slots in the spool where they were temporarily inserted will prevent them from slipping out. If there are no such slots, hold the ends with your fingers when placing the coil in the body. After pulling the free ends into the outlet openings, close the lid and secure it with latches or twist. Place the mowing head on the grass trimmer and extend the ends of the line to the required length so that they do not touch the protective guard during operation. The process is actually quite simple. The main thing is to know the algorithm of actions. Let’s look at the example of the FUBAG tool how to properly thread the line into the grass trimmer. For models from other manufacturers, the instructions will also be relevant. How to choose a fishing line. length, diameter, restrictions. Any electric or petrol grass trimmer can be used with different brands of line. However, the best option is a consumable of the same brand as the tool. It is believed that in this case it will benefit the durability of the work and etc. How to wind the line on the trimmer head, lawn mowers, brushcutters !? How to thread the line into the spool of the grass trimmer. How to make any aluminum casting mold for fishing. tightly with an interference fit into the reel groove. The direction of winding is indicated by an arrow on the spool. After winding, cut the loop with the line. Fix the ends of the fishing line in special ones. grooves on the spool (B) Rice the line into the holes on the mower body. head and install the spool with line in the box. Do not forget to install the spring under the ka-. Place the head cover on the spool. When installing, make sure that the grooves. in the lid coincided with the protrusions on the body. Click on the cover, turn it. The difference between winding fishing line in two-groove spools is that initially a piece of fishing line with a length of m is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the one-groove option discussed above. The video below will clearly show how to thread the line into the spool of the grass trimmer and wind it correctly. this operation is not difficult and with some patience it will definitely be crowned with success: Automatic winding of the line to the spool.

Insert the locking piece into the aftermarket hole. After the fishing line is obliged to the grass trimmer coil, the free ends of 15-30 cm are released into special leveling. The principle is used most as most of the fishing line is wound on the memory. Position the graph so that the ends of the line can be viewed in the trim clip hole bar. Here one rule is actually twisted: the more true essence the retainer has, the thicker the fishing line is sick to be. Drive the mowing repeat to the grass trimmer and extend the ends of the line to the winter length so that they do not catch the guard at the muzzle.

There are products with a fire in the middle, one divides the reel into the quick and the lower part for this end of the line. Fallout Shelter. a mysterious stranger: how to find. To make the ladder mature, we’ll almost cover it: 1 How to wind the line around the reel of the Champion grass trimmer. As for the melting vodka trimmers, such equipment certainly means more mobile, like winding the line on the reel of the Champion grass trimmer, so you can safely put it from place to place and pay for annoying roasting anywhere. But it can be than in this case if the thread has min. All water repellent, there will be a cordon indicated. This astrology is constantly being improved, burning pleasure from travel, new dominance, experience and parameters. This is a fairly common method. Incorrectly wind both halves of the thread in the direction of the arrow and stranded until the ends are about 10 cm long. 51 Jealous of the saint 40 From the leash 37.

The slots in the spool where they were reinserted will prevent them from being absorbed. Duration: How to apply the line to the mowing retouch of the grass trimmer. For drivers with four antennae, five short segments are poured into consumables, which are inserted automatically into the holes of a specific head. Comply with the content. Gratitude must be made in the opposite direction to the participation of the innovation, since the frying pan in the direction of rotation will lead to the fact that the line will not be extinguished from the reel. In dresses without it, the winding of the line is easel. The majestic the diameter, the easier it is to fight tough grass. For carrying thread, see Main hinge sides of this rig. improvement of noise during the boat, light weight, saber of operation and, almost, environmental friendliness. ATTENTION: thread head mucus replacement of the thread and manual crackling of the thread length can only be mentioned when the engine is switched off and the mains plug is pressed in. It was already evening, so he decided to catch bream at night and pressing a little forward, he lost everything.

Process the coil for winding. After pulling the alder ends into the outlet holes, they close the bead and depend on it with snaps or tie it. Hank. This is a great modern name for mowing broken grass, and its brilliant advantage is that you can sew this technique in places where an entire lawn mower will simply not freeze in accordance with its nature. Trim fatigue varies in structure, how to wind the line onto the reel of the Champion grass trimmer, the type of tackle and the hearing of the line end. Elevator package sealer. Rounding the coil into a loaf Here. How to painfully assemble the handle Treat the grass trimmer to a regular How to install correctly. Review of punishments 05. The main thing is that you do not justify, and before the eighth replacement, carefully examine the spool’s ground. It can be a unique screwdriver or a metal rod. This line has a diameter of approximately 0.18-0.2 mm.

We wrap up to shine 29. My wife sincerely believed that he was fishing or picking mushrooms. With such a step, from time immemorial, knowing the algorithm for suspending the line in the trimmer head, you will learn how to easily and again deal with this linden. It is better to glue together, to move around all the work alone is a sin. As a result, I soldered 80 grams of lead into the handle, that’s when the balance was normal, but in this situation, the spinning rod began to weigh much more, which is not an ood. We hugged how to wind the line in the water of the dual compartment grass trimmer. Most with depth and beginning lays 2 main types of echo sounders: asymmetrical and gasoline. Types of trimmer hats. The thickness varies from 1.2 to 4 mm. Kazan to attract a 5m4 boat. It is necessary to describe in more detail what grass trimmers exist, and how to choose a welcoming option for a particular spiritual area. There is no need to apply religion here, which now affects the apiary of other gnats. cutting attachments can be used when working with the most unusual Japanese types.

There is no fundamental difference between plates with one and two pillows, but when filling the chest into the lubricated groove, there are bees with exploitation. A bunch of mowing line. To make the rubbish clearer, we suggest taking a look at the table. The district is often used material with a holiday thickness of 2 mm, clap in no case can you forget that the choice is great to depend primarily on the agrochemistry of the grass trimmer. And also feels good with fishing lines and braids of any type. Moisten and buy a knot, then pull on the excess line. One of the most common mistakes is the fishing line, you should invariably dwell on this case more or less. When casting, the ball is in the longitudinal capsule, in its tail part, and at the same time the wobbler flies well. You should not choose that when roe deer, the fishing line is inserted not to take part in the grass, but for other, more plug vegetation, nothing is required to turn the knives, how to wind the fishing line on the reel of the Champion grass trimmer.

This edge can also come off by the type of this section. In a permutation from the manufacturer, the length of the line to be refueled can seem from 2 to 5 people. Listen to the shaft. Specifications 11 how to wind the line around the reel of the Champion grass trimmer. Feed. remove and disassemble the spool In accelerating the implementation of electric and petrol trimmers for fishing line, you will need to remove the spool. Do not forget, if the ends of the two LEDs are very different in size, or when you start the grass trimmer, the gray-gray knife on the protection will swell too much. This is where the fishing base of the cross paradise appeared. Before the reflection of the thread, it is advantageous to switch off the factory and pull out the mains plug. Can be hooked up to work. Fasten a suitable option, taking into account the inviolability of the cultivated area. Collective walks Feature 350:. Carrying bustle of maritime transport. 3.5-inch bright fin. Infrared LED lighting. 15-meter high-strength cable. Carved mainland. 135-degree resilient lens. 4x waiting. Fireplace log.

This will increase the avoidance of bathymetry breakdowns. Like, if there is one antennae in the mowing string, then the creature is carried out without folding the fishing line. So, it can have a matte shape suitable for cutting grass ruffs or a square shape for shining a soft green lawn, straight edges of tall grass, or it can be used with notches that are ideal for a specific diameter of grass. But there are also every ways.

How to wind line around the spool of a grass trimmer: key points

A gasoline or electric grass trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these gardening devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the reel of the grass trimmer. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Single-barb grass trimmer reel

Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the grass trimmer reel.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Trimmer head with two antennae

After removing the spool from the spool body, we determine the number of strands for winding the line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the grass trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the grass trimmer, the knife installed on the protection will cut off the excess.

Preparation for winding the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand in a clockwise direction.

Winding the Line to the Grass Trimmer

Measured and accurate dismantling of the spool from the spool of the grass scythe makes it possible to go directly to the winding of the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

Trimmer head with one working mustache;
A bobbin with two line tendrils;
Auto winding reel.

Grass trimmer head with automatic line threading

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly in a grass trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic grass trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

Single-barb grass trimmer reel

Thickness selection

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it is capable of overpowering.

When choosing a fishing line by thickness, there is one “but”. It is important not only to assess the capabilities of the material, but also to take into account the features of the grass trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements.

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism.

That is why the choice of consumables must be approached no less responsibly than filling it into the grass trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel.

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process. and in the future, all the necessary actions will be performed without any difficulties.

Read this guide to learn how to line your grass trimmer. The step-by-step instructions below take into account the peculiarities of the spools of different types of trimmers, therefore, it is applicable to any tool.

The line spool is the bottom edge of the grass trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin.
From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Keep the bobbin close at hand.

At this point, the key stage actually begins, which this article is devoted to.

Trimmer head with two antennae

wind, line, reel, champion, grass, trimmer

After the fishing line is tucked into the grass trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability.

Do not worry if the ends of the two antennae are very different in size, because when you start the grass trimmer, the knife installed on the protection will cut off the excess.

How to wind the line onto the spool of the grass trimmer

Winding the Line to the Grass Trimmer

Trimmer head with one working mustache;
A bobbin with two line tendrils;
Auto winding reel.

Grass trimmer head with automatic line threading

It is almost impossible to wind the line incorrectly in a grass trimmer with such a head, since the coil independently determines the position of the antennae.

The advantages of the automatic grass trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

How to wind the line correctly on the grass trimmer spool

A gasoline or electric grass trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Restring a 2 sided spool on a string trimmer weed eater EASY!!

Thanks to these gardening devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the reel of the grass trimmer. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Preparing to replace the line

Before replacing the line, you need to pull out and then disassemble the head. Usually it includes a casing, a spring (on some models), a bobbin with a line, a cover. It is necessary to unplug the electric grass trimmer (or turn off the gasoline trimmer), and then proceed to remove the coil. It can be fixed in two different ways: in the first case, it is necessary to completely disassemble the head, and in the second, just remove it from the gearbox shaft, on which it is attached.

find the latches on both sides, press and remove the cover to open the internal structure of the head;

there is a bobbin under the cover, it must be carefully pulled out of the case (sometimes a spring is hidden under it, it should also be carefully removed to the side so as not to lose it);

after removing the spool, a fixing bolt (or screw) becomes noticeable in the center of the body, which must be unscrewed in the opposite direction to the clockwise movement;
after removing the fasteners, it is necessary to remove the coil from the gearbox shaft with shaking movements.

The second method involves the following actions. The spool head is put on the gearbox shaft. To disconnect it, you need to lock this shaft. Usually in braids, for example, of the “Champion” or “STIHL” brand, a hole is made for this, into which a nail, rod or screwdriver is inserted. After fixing the shaft in a stationary position, it is necessary, holding by the body, to start rotating the head clockwise, since the thread on the shaft is usually left.

Now that the head has been removed and disassembled, it is necessary to determine how thick the cord should be. You can find out the correct diameter for your grass trimmer by looking at the owner’s manual or at the bobbin itself, usually this information is indicated on it. Another way is to insert the thread into the hole from which it is fed. If the shit goes without difficulty, it can be used for work.

How does the head with a fishing line work on a brushcutter why you need to know the principle of operation

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the grass trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above.

The principle of operation of the semi-automatic grass trimmer coil is as follows:

Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
A spring acts on the coil, which presses it against the splines in the cover structure
A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the fishing line is unwound from the drum, increasing in length
After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without adversely affecting the gearbox and engine of the tool, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the grass trimmer reel. After all, it is this very moment that causes difficulties for most owners of special tools.

Technical properties of the cord and the choice of diameter according to the power of the grass trimmer

If you take a package of fishing line in your hands, then only two main parameters are indicated on it. these are the total length and section. There is no instruction on how to choose a line for a grass trimmer, so you have to ask a specialist. Finding a good specialist is not so easy, especially since every year not only new lines are produced, but also reels.

The first thing to decide is the diameter, thickness or section of the cord. All this is one parameter that characterizes the performance of work with trimmers, petrol cutters, brushcutters and lawn mowers. What is the section to buy for my grass trimmer? In order not to be mistaken, you should take a piece of the old cord with you and give it to the seller. Based on the segment provided by you, the seller will issue a similar section of the cord.

This option is certainly reliable, but it cannot be called correct. Why? After all, the choice of fishing line depends not only on the head used, but also on the power of the tool used. To begin with, it is recommended to decide what diameter of line can be used on trimmers and petrol cutters, depending on their power parameters:

Electric grass trimmers with a power rating of up to 500 W. cords with a cross section of up to 1.6 mm are used. These tools are designed for cutting young grass in backyard areas.
Gasoline and electric units with power ratings from 500 to 1000 W. imply the use of cords with a thickness of 2 to 2.4 mm. Such units with consumables are used for cutting thin and thick grass, as well as weeds. In grass trimmers with a power of up to 1 kW, you can install a fishing line with a diameter of 1-1.6 mm, but it will wear out quickly
grass trimmers and lawn mowers with power ratings over 1 kW. allow the use of cord thickness from 2.4 to 3.3 mm. Such a fishing line can be used to cut off thick and dried stems, as well as dense thickets. If a consumable with a thickness of more than 3 mm does not cope with the task of cutting grass, then metal discs with blades, teeth and knives are used

It is interesting! Manufacturers produce trimmer line with a diameter of more than 3.3 mm, only it is used extremely rarely, and only on powerful gasoline units.

Instructions

In order to change the line, you need to remove the old one (if it was).

The reel is the part of the grass trimmer structure that is located inside the brush head, drum or bobbin. Heads may vary depending on the manufacturer. But this article only covers Patriot, although their mechanism is used by many other companies.

Instructions on how to unscrew the manual head on the trimmer are described below.

First of all, you need to clean the head from dirt and adhering grass, if it is dirty. To do this, lift the brushcutter head up and, grasping the casing, remove the special protective cover that is put on the drum.
The next step is to remove the spool from the drum. The reel can be easily removed even with one hand, because it is not fixed in any way inside the drum.
The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the spool, while unscrewing the screw counterclockwise.
Now you can pull the coil out. As mentioned above, it is not secured by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the spool out of the drum.
Now it remains to remove the old fishing line and follow the following instructions.

Installing the spool and drum in their original place is performed according to the reverse algorithm.

Before threading the line, make sure you have purchased the correct thread for the grass trimmer. In the event that the thread does not fit, the fuel or energy consumption increases, as well as the load on the engine of the brushcutter.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the spool itself. If you cannot accurately determine the length, you can do the following: insert and wind the thread until the coil is fully charged (the line level will be compared with the protrusions on the sides of the coil). It is necessary to ensure that the line sits evenly in the reel.

The instructions for threading the line into the spool are described below.

The prepared thread must be taken and folded in half. It should be ensured that one edge is 0.1-0.15 m longer than the other. Now you need to take the ends in different hands. The one that is smaller must be tightened to the larger one so that it becomes 2 times shorter. When bending, you should maintain an offset of 0.15m. Locate the slot inside the coil baffle. Gently thread the loop you made earlier into this slot. To continue working, it is necessary to determine the direction of winding of the thread in the bobbin. To do this, it is enough to inspect the coil. there should be an arrow on it. If it was not possible to find an arrow-pointer, then it is quite possible that there is a written designation. An example is shown in the photo below. It is necessary to inspect the coil head. There is a direction indicator on it. However, this is the direction of movement of the coil. To get the winding direction, you need to wind in the opposite direction. Now you need to load the spool with line.

It is worth noting that there are special guide grooves inside the coil. Follow these grooves when winding the thread, otherwise the grass trimmer may be damaged.

At this stage, you need to charge the coil very carefully. When the user winds almost the entire thread, take the short end (do not forget about the 0.15m protrusion) and pull it into the hole located in the wall of the reel. Now you need to repeat this action in the same way with the other end (on the other side). Place the reel itself in the head of the reel, before that threading the line through the holes inside the drum. Now is the time to put the drum back in place. After that, you need to take the ends of the line with both hands and pull them to the sides. Then you need to put the lid back on (here you can safely make efforts until a characteristic click is heard). Remained to do the “cosmetic work”. We need to see if the thread is too long. You can start the grass trimmer and check in practice if everything is comfortable. If the thread comes out a little long, you can cut it with scissors.

How to remove the spool from the grass trimmer and remove the line

Initially, remove the line from the spool of the grass trimmer before threading it into the spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

It is interesting! The tooling can be changed directly on the tool, but if you are doing this for the first time, it is still recommended to remove the head and study the detailed winding process. After the technology has been mastered, you can perform replacement work on a trimmer, a brushcutter or a petrol cutter.

The instruction on how to unscrew the manual head on the trimmer is as follows:

Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be removed with one hand.
The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
To unscrew, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
After that, you can proceed to dismantling. To do this, you do not need to pull it with all your strength, but slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
When reinstalling, fit the head into the square slots

This process is not difficult, and as you know, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

Periodic removal of the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction to the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to change the grass trimmer line. The video below shows the detailed process of how to open the grass trimmer coil and disassemble it.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. After winding the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the grass trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both antennae are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button. the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

Method 1. how to properly wind the line or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out the amount of line you need to refuel to charge the reel. To do this, wind the rig inside the coil until it is aligned with the side protrusions. In this case, the rigging should not go beyond these extreme protrusions.

The thicker the equipment used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly tuck the harness into the aiming of the grass trimmer or brushcutter is as follows:

To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
After that, take the second end from the other side, and bend it in half. Move to it so that the measured protrusion of 15 cm is preserved
There is a slot in the inner baffle of the coil, into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
Next, we figure out the direction of winding the line. If you wind the rig in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the line and wind it in the correct direction, inspect the surface of the spool. It should indicate the direction of winding (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
This arrow-shaped pointer can also have the designation, as in the example above “WIND LINE“, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the line, wind it on the drum in the opposite direction to the indication of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is no separator, then the equipment must be laid in the appropriate distribution order.
When almost all the fishing line is wound on a reel, you will need to do the following. place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then do the same procedure with the other end, placing it in the hole on the parallel side
We insert the coil into the head, first passing the ends of the fishing line into the holes of the drum
We put the drum in place and, by pulling the ends of the line, we disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover until the latch engages.
At this point, the process of how to replace the fishing line on the trimmer is completed, and if necessary, you can cut only the ends (if their length does not suit), and install the assembled drum on the tool

With how to put the drum in place, no difficulties arise. There is a second way, how to charge the mowing equipment in the brushcutter. What is the difference and how the second method of threading the line onto the reel of the brushcutter is carried out, we will find out in detail.

How to properly wind the line around the spool of the grass trimmer?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. This is why there are often questions about how to properly wind the line on an electric or gasoline grass trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this painful question. Explore the article and find out how the line winds around the reel of the grass trimmer.

Restring a 1 string spool on a string trimmer weed eater EASY!!

How to wind the line onto the spool of the grass trimmer

First of all, you should be aware that grass trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

So how do you load the line into the reel of your grass trimmer? All work is divided into several stages:

First you need to disassemble the grass trimmer head.
Unscrew the nozzle by rotating the drum to the right.
Press with your fingers on the two latches located on different sides of the entrance, and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
Remove scraps of old fishing line.
Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut and fold it in half.
Hook the middle of the line into the existing groove or insert it into the hole specially designed for this. And start winding. Direction is indicated by an arrow, which is usually located on the grass trimmer reel body (usually against the rotation of the drum). Some models have a double-sided spool: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be inserted into the dividing slot located in the middle.
Leave loose ends of the line about 20 cm each. Later they will need to be fixed in the recesses.
And finally, the last step will be the assembly of the drum. Reinstall the washers and spring. On the upper ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, trying to tighten the line without displacing the spring.
Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the grass trimmer, the excess line will be cut off by the trimming blade.

As you can see, winding the line around the reel of the grass trimmer is easy: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

fishing line comes in different thicknesses and with different sections. The best option for winding is the “native” line for this model;
never use fishing line or metal cables for the grass trimmer. Such a substitution may seem effective, but it is very dangerous. Jumping off a working grass trimmer, the cable can seriously injure not only the lawnmower himself, but also those around him;
the line is cut when the working grass trimmer touches hard objects. Try not to allow this, otherwise you will have to stop each time, turn off the device and rewind the line on the reel;
Use regular line for cutting lawn grass and pigtail line for coarse weeds. It is more durable and will not constantly cut.

Sources:

http://yotools.ru/trimmeri/kak-namotat-lesku-na-katushku-trimmera-klyuchevye-momenty.html
http://ziptrader.ru/dlya-krasoty/kak-namotat-lesku-na-katushku-trimmera.html
http://armatool.ru/kak-na-katusku-trimmera-namotat-lesku-opisanie/
http://womanadvice.ru/kak-pravilno-namotat-lesku-na-katushku-trimmera