Muffler for a chainsaw with his own hands

Muffler for a chainsaw with his own hands

All chainsaws have only one significant disadvantage. it is the noise at work, which in some places (dachas, homesteads) disturbs and irritates many people. If the noise from the saw’s operation makes it difficult to concentrate, it is also possible to use headphones to suppress the noise. But will not all around walk around in headphones, while someone makes noise.

A clogged or unrepaired muffler is the reason why the engine constantly stalls or won’t start at all.

It so happens that the chainsaw normally operates at low RPM, but it is necessary to add gas, as she immediately sneezes and shuts down. The reason is usually that the exhaust cannot pass through a clogged muffler and has to go in the opposite direction. To do this it is enough to take it off and clean it, if it is dismantled of course, if not, you will have to dry it with hot air, using a hair dryer.

The main cause of muffler pollution is excessive oil that gets diluted with petrol and sits on the muffler walls.

If you decide to clean a non-dismountable muffler yourself, keep in mind that you cannot do it dry using the same hair dryer, because the hazardous substances are extremely harmful to health.

Although most chain saw producers try to muffle engine noise as much as possible, it does not result in anything good, and it affects the power of the machine in the first place.

Professional chainsaws, like Husqvarna, for example, cannot work quietly at all, because the power and rpm are very high, which leads to a lot of noise. Trying to muffle the roar of the motor, while maintaining high performance, is extremely difficult. But there are people who use an ordinary bucket of water and a plastic tube, one end dipped in water and the other end screwed to the exhaust pipe. There is efficiency from such actions, the sound of the motor becomes quieter.

Assembling process

There are several ways to upgrade a chainsaw with your own hands. With the right approach, the homemade exhaust system will act effectively, without reducing the power of the unit.

The easiest way to get rid of the rumble is to use a flexible plastic duct and a container of water. The hose through thermal insulation gaskets is screwed to the exhaust pipe, its other end is lowered into the water and rigidly fixed to the tank.

Gradually cooling and losing speed, the exhaust freely comes out of the engine. The contact with the air is neutralized by the water. To make such a muffler for a chainsaw, you will need at least 3 m of flexible pipes and a bucket with a capacity of 10-12 liters. This design is good for running on flat open ground without moving around the lot. Used to cut firewood or logs in the backyard.

Decrease exhaust noise of the 2T engine. it is possible?

I think the muffler on two-stroke engines works in tandem with the engine and interconnects, t.е. its design change can affect the performance of the engine as a whole. am i right?

I have two engines from chain saws, both shouting until it is impossible, with one of them began to experiment, made a muffler. But it is harder to start and has lost rpm.

how you can reduce the noise from the engine? I want to make a gasoline generator, but how to operate it in the city, garage or in nature with such noise. I do not know. do not offer to switch to a 4t engine, t.к. these have nowhere to go

can anyone throw up a drawing of a not too complicated muffler?

Messages: 37 Toyota Vista 4VD MCCP 2.0 VX SV43

outdoors only covered either with a box or further away, by Google, I think it is possible to find old books on engines d6, d8. from personal experience i can say that i have done nothing, with my moped. As the noise was so noisy and noise, through long poboros bungled myself a sosnolny muffler from scraps of stainless steel tubing. https://zhurnalko.net/=sam/junyj-tehnik/1970-11—num35

How to reduce the noise chain sawLink to main publication

How to Make a Chainsaw Noiseless with Your Own Hands

The question of how to make a chainsaw silent with their own hands is asked by almost every owner of a private house or a summer cottage. The noise emitted by the tool at high rpm is severe and reverberates for hundreds of meters. Loud noises annoy the neighbors, they fatigue the master himself. Understanding the nature of this phenomenon, you can make a chain saw quieter, spending a minimum of time and money. Rattling occurs when gasoline explodes in the cylinders and exhaust gases come in contact with the air. Eliminating these factors can reduce noise.

Possible inconveniences associated with a silent muffler

The car will now run quieter, which we wanted to achieve, but there may be some drawbacks. increasing the overall weight of the exhaust system. That is why it is necessary to install stronger brackets, so that on a rough road the exhaust pipe would not tear off. There are also cases, when they hang rubber shock absorbers. But in fact, homemade resonator will weigh about 2-3 kg.

You should also test in action, how the exhaust system works, so that gases would normally come out through the exhaust pipe. So you need to check at higher revs, then you will be able to draw the right conclusions. But as a rule, through such a resonator gases will come out without difficulty.

And further on the video is another way to reduce the sound of the muffler by making a really very quiet exhaust system:

make a chain saw quieter

Need a specialist who will build a muffler for the Stihl. I’m in the wood house business and it’s a disaster when you have 10 or 12 saws in an office. In 100 meters of residential houses and I’m afraid that the residents will soon me to put it mildly unlikely. If anyone can make one, I’ll buy it.

Zhora spb wrote: I produce wooden houses and when 10-12 saws are working it is a disaster.

Masters say that the gasoline tool has some kind of recoil, in general, prodolyvali does not work

Zhora spb wrote: craftsmen say that chain saws have some kind of kickback,

zhora spb wrote : generally sold out does not work

zhora spb wrote: craftsmen say gasoline-powered tools have a kick

You may even make a mobile version. With two-stroke machines (if they are two-stroke, but I never worked with 4-stroke, for example) it’s not so easy to make something with the exhaust.

Zhora spb wrote: I need a specialist who will build a muffler for the Stihl.

There are already mufflers on chainsaws. It makes no sense to refine them, i.e.е. Theoretically it can be done but how the engine performance will change and if it will work at all is hard to predict.

I’ve run into problems like that too.

guron wrote: Put a sound reflective fence

And noisy work carried out only strictly during working hours, so as not to disturb the sleep of the neighbors, say from 10-00 to 18-00. If this regime will be strictly enforced, the neighbors are likely to get used to it.

Well in general there is nothing difficult it seems. Purely theoretically: take an ordinary tin can made holes in it, wrapped with glass wool and screwed to the regular muffler. But I think the sound will really reduce the decibels by 10 decibels and to be completely silent muffler should be like a car about the sound-reflecting fence cool idea. It might work.

Flange on the cylinder, hose on the flange and into the canister with water. It will be like a boat motor. Mobility will be reduced, though.But.

Also wanted to throw 10 kopecks, t.к. I used to work in a car service, they made straight-through mufflers with bass nozzles for street racers. For those interested: “

Insertion like a drill for winter fishing. Made an auger for 20 revolutions and stuck it in the muffler pipe. The sound has not become quieter, it has only changed. He roared on one note, on the letter: Shh-shh-shh-shh-shh-shh-shh-shh. Like an air compressor hose with a sandblaster. It’s wild and unpleasant.

I would go with electric saws so I could use them wherever I could, and use gasoline-powered saws when I couldn’t use electrics. Power saws are probably not the way to go.к. already bought a bunch of chainsaws, it’s too expensive to buy an electric. The quietest but not the most mobile option already mentioned. a hose in a bucket of water. This is how loggers poachers cheat. If the muffler in the form of a cube-bottom, then unscrew 3 bolts (nuts) that stick out of it, take out a plug (or whatever is inside? cone?) And for the 3 holes we plant a homemade flange of some kind, which is connected to the hose in a bucket of water. The main thing to count: 10-12 of these flanges cut from roofing iron with scissors on metal or 10-12 anti-noise fences do Incidentally, the hoses stock up. rubber quickly burn through, we need something with metal. shell. And about “will not run the engine normally”. look how the Americans converted on the aircraft models work 2-stroke chain saws: just the exhaust pipe and that’s it!

How to make a muffler for a chainsaw

There are several options on how to make a noise reduction device yourself.

There are simple noise reduction techniques, such as placing a metal sponge in the muffler. The method works, but the power of the engine is somewhat reduced.

Another uncomplicated recommendation on how to make the chain saw run more quietly: put a hose over the exhaust port and dip it into a bucket of water. To do this, unscrew 3 bolts from the damping cube of the saw to remove the plug. In the freed space insert the homemade flange (cut out of roofing iron) and fasten it to the same 3 bolts. A rubber hose about 3 m long is put on the flange, the other end of which is immersed in water.

It is better, if the flexible hose is with metal sheathing. this will prevent its rapid deterioration. You can replace the bucket with a plastic canister.

You can make a chainsaw muffler with your own hands from tin sheets. You need to bend two pipes out of them. One should match the diameter of the hole for the saw’s exhaust discharge, and the other should be wider by 2.5 cm. Drill many 3mm diameter holes in the narrow pipe. They can be positioned as you like, but the distance between them must be at least 5 mm.

On the resulting peorized tube wind metal wool, basalt cord and aluminum wire. The winding is rigid, otherwise the exhaust under pressure will blow it out. A wide tube is put on top and connected to the inner tube with bolts. The end face is welded with a steel washer. The received additional muffler is put on regular muffler and fixed with rivets.

How to reduce the noise of a chainsaw

How to make a muffler for a chainsaw

Chainsaw. it is a universal tool, the sphere of implementation of which is very wide. In view of the special importance of this kind of technology modern manufacturers offer customers a wide range of different models not only Prof, but also domestic purposes. Let’s talk further in this article about how to make a muffler for a chainsaw.

Scopes of application

As it was already mentioned above, such equipment has a wide range of uses. In addition to the main purpose. the implementation of the logging of trees and timber procurement, such equipment has found its application in other areas of human activity. And today you can buy not only professional, but also domestic models.

They are very necessary for them in homestead plots with fruit tree plantations. Also relevant when performing construction and repair work if a wooden structure is being built or restored. In addition, they are used for making firewood in the villages and the like.

operating noise

The work of any gasoline tool is accompanied by the exhaust of fuel combustion products, as well as noise from the engine operation. This also applies to domestic models. Many manufacturers are trying to create the most quiet models, but in this version they are not distinguished by high power and productivity.

And what to do if you need a powerful and at the same time quiet model to work on the homestead or during the construction of a house from a log cabin? Then you can make with your own hands a muffler for such a tool, which prevents too much noise from its motor work. Of course, you can buy a ready-made version, but it will cost many times more.

Muffler for STIHL chain saw

This video shows the Stihl with home-built muffler which really lowers noise

Muffler for chainsaw muffler

A must have. SIGN UP, comment, like. Subscribe, comment, put like. Thank you! This content.

How to make a muffler as cheaply and without hassle as possible? We will talk more about this later on.

What is a muffler?

This is a special unit, which is designed to reduce the level of noise from the operation of the car engine, chainsaw and other equipment of a similar nature. In other words, the muffler is able to reduce the noise that accompanies the operation of the engine. But how to make it with your own hands? For this you can use improvised materials. From the tools you will need a welder, a drill, drills of different sizes, sandpaper, thin wire, stainless steel wool and basalt fiber.

Reducing the noise with their own hands

To do this, perform the following actions:

• Take a sheet of stainless steel, 1 mm thick, and twist it on the rollers. You should end up with a round tube, but afterwards you need to make it into an oval. If there is a pre-made tube with parameters that fit your chainsaw, you can use that;
• Weld the joint and apply a little pressure to get an oval shape;
• Weld a pipe smaller in diameter than the muffler and make a lot of holes in it so that the pipe is peorized;
• Wrap stainless steel wool around the peorized pipes to keep the muffler packing from blowing out;
• It remains as firmly and reliably as possible to wrap the basalt fiber on top of the stainless wool. Use for this purpose a strong wire of thin diameter;
• We fill the interior of the future muffler with peorized pipes, wrapped with stainless wool;
• Carefully grind and then polish the joints with fine abrasive paper;
• Connect the resulting unit to the chainsaw as securely as possible.

See how the following photo shows the finished unit assembled according to this action algorithm.

The resulting unit will cost its creator a penny, but will show high efficiency to reduce the noise of the working chainsaw.

Do it yourself

To save money and time spent searching for the right workshop, I advise to make a muffler at home. This is not as difficult as it seems at first glance.

All you need is a regular sheet of 1mm stainless steel, an iron tube of a smaller diameter than the muffler, stainless steel wool, basalt fiber and a little patience.

• We take the sheet steel and twist around the rollers, the result is a round tube, but you will need necessarily tube oval shape. To do this, using a weld, heat and then press the tube, you should get an oval shape;
• If you have a pipe of suitable diameter, that’s good, if not, you need to make it with a welder. To do this we take a sheet of metal, mark the necessary dimensions and cut it by welding. Then we make a tube, the seam should be thin and without bumps;
• When you have a ready tube, it is necessary to do in it as many holes as possible, and make holes can be as chaotic and in a strict order, it does not play a role;
• Then we take the stainless steel wool, prepared in advance, and begin to wrap it around the outside of the pipe. This is necessary in order to avoid blowing out the muffler’s skin;
• Then on top of stainless wool wrap basalt fiber (this is the most suitable material) and to keep it all from slipping, fasten the wire, which should be thin and at the same time strong;
• We put the wrapped tube in the future machine and sandpaper it all, pay special attention to seams and joints, so they do not stand out much;
• When all this is done, the resulting unit should be attached to the chainsaw as firmly as possible, so it does not come off at the right time.

Such a homemade device, if everything is done correctly, will serve long and significantly reduce motor noise, works well on Druzhba chain saws. Another advantage of a homemade muffler is that it will cost you a pittance. You will spend only time, but it is worth it.

Another silencer option is to put baffles in the pipe that is in the silencer and thus reduce the noise level of the motor. This is because the noise itself is a strong oscillation of air, which escapes from the muffler to the outside at great speed.

In order to reduce the noise of operation, it is enough just to drill holes in the pipe and insert baffles in them at equal distances. You will get a lot of baffles and gas will come out step by step and the pressure and noise will decrease. Accordingly the velocity of the gases will drop, which will reduce the noise.

If you want the gases to escape faster from the cylinders and thereby reduce the engine power, so that the performance of the saw increases, remember that the noise will be several times greater.

In order to achieve this, you need a straight-through muffler, which can be made from a pipe according to the sketches of the old muffler, unscrewing and subsequently using all the bolts and nuts.

It is a good idea to use a steel muffler because it will last longer. If you don’t have a suitable steel tube, you can make one from steel plate. Using a welding machine, you can make a tube of the desired diameter and size.

The muffler should work as a single piece and if you try to change something yourself, including improve the muffler without any drawings, it is quite difficult and not everyone can make it.

At best you will lose power and at worst the chain saw will not start.

For chain saws like the STIHL 180 it is best to buy a original muffler, so you can change it yourself without any problems.

Therefore, if you have some knowledge and well working savvy, you should try to make an additional muffler yourself, thereby saving money and possibly get to make such a device, which will really make the work of the chainsaw much quieter and you will not have to constantly quarrel with the neighbors or with the people around you.

Materials and tools needed

In standard cutting products, the exhaust system is as short as possible. This is decided to achieve the power required to turn the chain quickly. In order not to impair the performance of the equipment and make it quieter, you need a thoughtful and comprehensive approach.

To make a muffler for a chainsaw with your own hands you need the following tools:

• Measuring tape;
• Welding machine;
• Metal shears;
• Bulgarian;
• Hammer;
• Core;
• Marker;
• Rivet;
• File;
• Electric drill;
• Construction hair dryer;
• Screwdrivers.

Depending on the features of the improvements introduced, materials may be required:

• Stainless steel sheet;
• Rivets;
• Bolts
• Screws;
• Basalt fireproof cord;
• Wire;
• Hardwoods for rollers.

The following products should be used to protect hands, skin, vision and breathing during use:

The design of the tool ensures that the noise is partially absorbed by the housing. If it has large gaps, they can be repaired with silicone-based mastic. The material will reduce vibration, plastic and metal rolling.

Partner NO POWER. Chainsaw Repair.

Quite a common problem, this on a chainsaw

no power. What to Do No Power on a Chainsaw? Of course, it is better to wait 24 hours after cleaning.

A detailed video of the cleaning process will help to do the job properly.

After all the products are dry, you need to assemble the carburetor. How to make a muffler for see how the following photo shows the finished unit. The detergent usually evaporates completely in 24 hours. It is better to wait 24 hours after cleaning, because detergent residues on the parts can get into the fuel compartment and emit toxic gases as they burn.

Another important nuance related to the disassembly of the chainsaw is that it is necessary to install and adjust the needle valve petal extremely accurately, otherwise the chainsaw may not start. To check the correct setting of the blade, you can use the blade. After placing it on top, see how freely the blade rotates. If there are no problems, then everything is fine. you can continue with the assembly. How to make a muffler on a chainsaw?. Get expert answers for free! If there are problems with the stroke, you must either press the paddle or bend the edge of the paddle.

How to Build a Quiet Muffler for the Chainsaw

Is it possible to make this motor quiet?The customer comes to the store to return the product to the chain saw.

what claims? Yes here in the summary writes that an hour slices 4 cubes of wood, and I have more than 3 does not come out now check (starts) wow, and why do you have it rustled? I have two motors from chain saws, both screaming beyond belief, with one of them I started experimenting, made a muffler.

The shocking sound is gone, the exhaust is quieter, but the engine kind of still makes a decent noise. Quiet muffler on a chainsaw. How to make a muffler quieter.How to Make an Exhaust Pipe for a Chainsaw. Lions.

Chainsaw muffler video. Mufflers. Parts for chainsaws and trimmers A chainsaw is a versatile tool with a wide range of uses.

Due to the special importance of this kind of equipment, modern manufacturers offer customers a wide range of different models not only How to make a muffler for a chainsaw at home criteria. Good time, dear readers subscribers to the Blog Andrew Noack.

Make such a device, which really will make the chainsaw significantly quieter and for you will not have to fight with How on the chainsaw to make the muffler quieter? Soundly works. There is an Alpina and a Chinese, Patriot something.On the Chinese just two holes with complex geometry.

Needed materials and tools

In standard cutting products the exhaust system is made as short as possible. Such a decision is made to achieve the power needed to turn the chain quickly. In order not to impair the performance of the equipment and make it quieter, a thoughtful and comprehensive approach is necessary.

Making a muffler for a chainsaw with your own hands involves the presence of such tools:

• tape measure;
• welding machine;
• metal scissors;
• angle grinder;
• hammer;
• core;
• marker;
• riveter;
• file;
• power drill;
• Construction hair dryer;
• screwdrivers.

Depending on the features of the improvements to be made, materials may be required:

• stainless steel sheet;
• rivets;
• bolts;
• screws;
• basalt fireproof cord;
• wire;
• solid wood for the rollers.

To protect hands, skin, eyes and respiratory organs, the following means should be used during work:

The design of the tool provides for partial absorption of noise by the body. If there are large cracks in it, they can be sealed with silicone-based mastic. The material will reduce vibration, rattle plastic and metal.

How to make a chainsaw silent with your own hands: describing point by point

Good afternoon, dear readers subscribers to the Blog Andrey Noak. Recently, my neighbor was cutting down trees on his property and getting firewood. Of course he used a chainsaw.

Although he bought a household saw, not a professional one, it made a lot of noise. While it was working all the neighbors, including me, got tired of the noise.

Here I came up with the idea, to tell him how to make a muffler for a chainsaw with his own hands.

Muffler for chainsaw muffler

The thing you need. SUBSCRIBE, comment, like. Subscribe, comment, put. Thank you! This content.

Muffler for STIHL chainsaw

The video shows the work of the Stihl with a homemade muffler, really lowers the noise of the engine more than 50% customers.

How to make a homemade muffler. Engine performance is judged by the noise of the gases I went when I made a copy of Yak-50 two years ago, the goal was not to get quiet or to make an auger for 20 revolutions and shove it into the muffler pipe. The sound has not become quieter, it has only changed.

Roared on one note, on the letter: Shh-shh-shh-shh-shh-shh-shh-shh!Power saws are probably no good, because.к. already bought a bunch of chain saws, it’s too expensive to buy electric as well Bosch AKE 30 LI cordless chainsaw. A silent muffler on a chainsaw. How to make a chainsaw ” similar videos.

Somehow it happened, the saw was on sale not so expensive. CTS CS cordless chainsaw from OREGON. Quiet operation without soot and wires. How to make a silencer for a 2-stroke engine with their own hands. Construction, repair with their own hands. How to make a chainsaw run quietly.

Chainsaw repair with their own hands Chainsaw cannot be attributed to complex devices if desired And yet the repair of chain saw can take a lot of time The attachment to the chainsaw “angle grinder” performs such operations as cutting metal and stone grinding surfaces and other.

While a special engine is very expensive, a boat motor made from a chainsaw will be an excellent budget solution. How to start a chainsaw. a couple of the most popular ways. Disassembly of a PARTNER 352 chainsaw. Airplane from a chainsaw Test.chainsaw muffler. How to make a band saw PART. 1.

That’s where I got the idea, to tell him how to make a muffler for a chainsaw with his own hands.If you are clever you can make the same Ural chainsaw work much quieter and it will not affect its performance in any way. I have an idea. to adapt a moped muffler to a chainsaw.

What do you think? Did anyone?I once had to quietly knock down a couple of oaks. Two-handled long, so we decided to upgrade the Stihl. Muffler for a chainsaw. Make chainsaw quieter as air compressor hose with. Uploaded by.

I use my chainsaw as a boat motor, so I made a muffler.In this video I’ll show how to upgrade a chainsaw in a simple way, to make it safe for Prank hell How to make a chainsaw as quiet as possible, and the loss of power to be to 15-20? To cut down trees at night.

It will be both environmentally friendly and quiet and healthy!In my opinion, if you can’t stand the exhaust, there are two ways out: pause and have a Twix or go electric.

other how to make a silent muffler for a chainsaw, self DIY for the car with his hands, plamegassitel instead of a catalytic converter in Ford, metal mesh in a straight pipe, remove the catalyst VAZ 2114, resonator for FORD explorer 1991 How to make a chainsaw from To make a chain saw, you need: Lemonade Shihan, a rope, a lighter, awl, kants. knife. How to make a quieter muffler on idle speed not to disturb the neighbors) AstalavistA inD 3 Year. How to make a quieter chainsaw. photo Mastergrad Forum.Quiet exhaust with their own hands VAZ 2109. Raum Pro. How to make a quieter muffler on a chainsaw video. Mosstroyservice. Silent? How to make a chainsaw ” similar videos how to make a chainsaw. But how to make it with your own hands? How to make the exhaust quieter on a chainsaw? What can be added to make it work more quietly? That’s why manufacturers around the world are creating more and more models with high power and light weight. Let’s talk further in this article about how to make a muffler for a chainsaw.And what to do if you need a powerful and at the same time quiet model to work on the homestead or the construction of a house from a log cabin?

Making it yourself

In order to save money and time spent looking for the right workshops, I advise to make a muffler at home. It’s not as hard as it looks.

All you need is an ordinary sheet of 1 mm stainless steel, an iron tube with a smaller diameter than the muffler, stainless steel wool, basalt fiber and a little patience.

• Take a sheet of steel and wrap it around the rollers, you end up with a round tube, but you will need an oval shaped tube. To do this with the help of welding heat and then press the tube, you should get an oval shape;
• If you have a pipe of suitable diameter, it’s good, if not, you need to make it with a welding machine. To do this, we take a sheet of metal, mark the required dimensions and cut it by welding. Then we make a pipe, the seam should be thin and without lumps;
• When the tube is ready, you need to make as many holes in it as possible, and you can do the holes as chaotic or in a strict order, it does not play any role;
• Next, we take the pre-prepared stainless steel wool and start wrapping the outside of the pipe. This is necessary in order that there was not a blowing out of the muffler shell;
• Then over the stainless wool wrap basalt fiber (this is the most suitable material) and to keep it all from slipping, fasten the wire, which should be thin and at the same time strong;
• Let’s insert the wrapped tube into the future machine and sandpaper it all, pay special attention to the seams and joints, so they do not protrude strongly;
• When all this is done, the resulting unit should be attached to the chainsaw as firmly as possible, so that it does not come off at the right time.

Such a homemade device, if everything is done correctly, will serve for a long time and significantly reduce motor noise, works well on Druzhba chain saws. Another advantage of the homemade muffler is that it will cost you a pittance. You will spend only time, but it is worth it.

It is possible to apply and such variant of a muffler: to put the partitions in a pipe, which is in a muffler and thus to reduce the noise level of the engine. This is because the noise itself is a strong oscillation of air, which with great speed comes out of the muffler to the outside.

In order to reduce the noise of the work, just drill holes in the pipe and insert the baffles at equal distances. You get a lot of divisions and the gas will flow out step by step and the pressure and noise will decrease. Accordingly the speed of gases movement will fall that will lead to reduction of noise.

If you want to make the gases leave the cylinders faster, thereby reducing the engine force, so that the performance of the saw increases, remember that the noise will be several times more.

To achieve this you need a straight-through muffler which you can make from a pipe based on the sketches of an old muffler by unscrewing and subsequently using all the bolts and nuts.

it is advised to choose the pipe from steel, then the muffler will serve longer. If there is no suitable steel tube, it is necessary to make it using a steel sheet. You can use a welder to make a tube of the necessary diameter and size.

Factory and so everything is provided, everything should work as a whole and if you try to change something yourself, including to improve the muffler without any drawings, it’s quite difficult and not everyone can get.

At best, power will be lost, and at worst. the chainsaw will stop starting.

For chainsaws like the STIHL 180 it is better to buy a native muffler, which you can change yourself without any problems.

Therefore, if you have certain knowledge and well working savvy, you should try to make an additional muffler yourself, thereby saving money and maybe get to do this device, which really make the work of a chainsaw much quieter and you will not have to constantly quarrel with the neighbors or the people around you.