Why the grass trimmer reel is throwing out the line for trimmer

Grass trimmer line unwinds C Grass trimmer reels. ANTIRUN.RU

If the grass trimmer shaft does not coil up when lightly striking the ground with the button, the following are the most common causes.

Option 1. came jamming, t.е. Cord caught between coils. This discrepancy usually occurs if the user has wound the line for the trimmer on the spool unevenly, with crossed turns, or wound it with insufficient tension. In the last case, when rotating the mowing head at high revolutions the cord begins to tighten under the influence of centrifugal force, which can cause inter-scroll clamping of the line.

Variant 2.4. very short ends protrude from the head. the line for the trimmer may not come out when hitting the ground, if its ends, sticking out of the head, are not long enough (not long enough). Then the centrifugal force is not enough to stretch the trimmer line. Therefore, it is necessary to stop the machine (turn off the engine or disconnect the trimmer electric grass trimmer from the mains) and pull the line for the trimmer manually, having previously pressed the button.

Variant 3. trimmer line is soldered inside the mowing head. This leads to the fact that the coil is frozen and does not even spin when you press the button. For the most part, this happens for several reasons: poor quality cord, overheating of the coil during prolonged operation of the unit, the impact of the line on solid objects.

  • In the beginning, the cord from other manufacturers you will like is made of low-quality and fusible materials that do not hold the mechanical and thermal load. Therefore “branded” lines should be preferred.
  • If you did get the line for the trimmer unknown properties, and it often soldered in its time of operation, then of course follow the example of some users, who after filling the cord in the coil or lubricate it with silicone grease (from a canister), or mineral oil. This procedure greatly reduces the possibility of the line strands soldering to each other.
  • A trimmer line can also solder if, while mowing, it hits a hard object (a rock, a fence, a dry branch, etc.) and causes the line to snap to one another.д.). In the course of this action, the line is slightly stretched and is pulled back into the head at high speed. Friction causes the cord to become warm and the wires to stick together. The only thing that will do to eliminate this malfunction is to open the grass trimmer spool and rewind the line for the trimmer.
grass, trimmer, reel, line

There are situations when a weed trimmer user notices a very sharp line flow rate. Not once did he hit the button on the ground to lengthen the line. The premise that the line for the trimmer spontaneously lengthens, cutting on a special knife on the hood of the device is the absence of the spring in the mowing head.

Black and Decker Trimmer Line Spool Replacement

Also, the line for the trimmer can be extended without using the button, if the spring is loose. if check of the spring confirms this fact, it is necessary to put some washers under it to increase its pressing characteristics.

Owners of trimmers, mostly new, get confused, adjoining to panic when there is a need to change the cutting tool or line for trimmer in the coil. Often, when trying to unscrew the mowing head, users simply cause it to fail, not realizing that it unscrews in the opposite direction.

  • Before you tuck the line for trimmer in the coil, turn off the engine trimmer as it is called, turn off the trimmer elletricheskoe for grass, to avoid injuries that occur when accidental start cutting tool rotation.
  • Unscrew the nozzle attached to the gearbox shaft. To do this, secure the shaft by aligning the holes on the washer on the shaft and inserting a rod or screwdriver.
  • Unscrew the nozzle. It is important to know that the thread on the shaft is left. Because the grass trimmer spool should be turned to the right, in other words clockwise.
  • Disassemble the mowing head. In most cases, the cover of the head is attached to the locks. To remove it, will need these locks to sink into the body, pushing down the edge of the cover. If pass, if your trimmer has an automatic mowing head, which has a button at the bottom, the disassembly of the head should be carried out accurately, because there is a chance to lose the spring, which occasionally flies out when you remove the cover.
  • Cut off the required amount of fishing line. It is normally 5 meters long. Use cord of the same cross section as shown in the manual. Do not try to exceed the line’s maximum diameter, because this puts too much pressure on the engine and increases gasoline consumption.
  • Locate the center of the cord by folding it in half. You will have a loop.
  • There are special grooves (there may be holes) cut into the inside of the spool. Stick the loop of fishing line into this groove.
  • Wind the line for the trimmer on the spool by turning it counterclockwise. It is necessary to wind the cord very evenly, the turns should be laid without overlapping and with a good tension. When you have finished taping it up, leave about 20 cm of loose line, and fasten the ends in the slots on the sides of the spool.
  • Assemble the mowing head. Before assembling the nozzle at all, do not forget to insert the spring and the washer (if available). Insert the spool into the body and put the ends of the line through the holes or eyelets.
  • Put on the cover and fasten it with the catches.
  • Screw the mowing head back onto the gearbox shaft, also securing it with a screwdriver. Screw the grass trimmer spool will need to the left (against the h. arrow).
  • Take a piece of plywood or textolite and draw a circle circumference of about 14 cm.
  • Cut the disk through the jigsaw as it is also called a hacksaw for metal.
  • Drill a hole in the center of the disk, the cross section of the shaft gearbox. And before you install the disk on the shaft, put a washer on this address.
  • On the sides of the disk of course screw small brackets as it is also called make 1-2 holes on the reverse sides. They will be used to thread the line.
  • To fix the line for the trimmer, of course screw a few self-tapping screws into the plywood.

Such self-made mowing head is fixed on the shaft by the nut. Do not tighten or otherwise unscrew the nut without fixing the shaft. To change the cord, it is enough to release the self-tapping screws, insert a piece of fishing line of the required length and press it again.

You can also make the mowing head from an iron sheet to fasten the line here. How to do it, you can understand from the following video.

Change of magneto

To remove the magneto, you must remove the plastic cover with a grass trimmer. This process is different for different models of brushcutter. Usually you need to unscrew the bolts, but on some petrol trimmers may need to squeeze the latches. After that the coil is exposed. To remove the part, you need to unscrew the holding fasteners and disconnect the wire.

When installing the new part, it is necessary to adjust the distance between the flywheel and the magneto. This requires turning the handwheel upward with the magnets, install the coil and fix it, but the screws do not tighten completely, so that there is a small distance between the parts. Next, between the reel and the flywheel is required to put a calendar, business card or four folded cardboard A4 sheet, you can also use a plastic strip cut out of a bottle. These tricks will ensure proper clearance between the flywheel and the magneto. A more competent solution would be to implement a special template, but to get it for the sake of the 1st time is not expedient. Next, it is necessary to screw the fasteners, pull out the object that is between the parts, and, holding the magneto by hand so it does not spin, tighten the fixing screws tight. After that, you should turn the handwheel and make sure that it does not catch the spool anywhere. Now you need to connect the wires and plug the candle into the cap, then check the operation of the device.

Types of trimmer heads

Head for grass mowing is a cylindrical body, in which is inserted a spool (coil) with a fishing line (cord). Such a design can be installed on both gasoline and electric trimmers for grass. The heads differ in the way they are filled and the cord supply and there are 3 types.

  • Automatic. The cord is fed after the user has slowed down the motor. Although the automatic feeding of the mowing line is convenient, if you perform a large amount of work, these bobbins have one drawback. High thread consumption.
  • Semi-Automatic. Using this type of head does not require complex manipulation by the user. The way they work is that the cord is automatically lengthened when the device is running at full speed. Just lightly hit the grass trimmer head on the ground (this removes the cord clamp), and the centrifugal force takes the trimmer line off the spool, and then cut to the desired length with the knife located on the protective cover.
  • Manual. To extend the cord, the machine must be stopped, after which the line for the trimmer is removed manually.

Based on the above, semi-automatic spools are the best option. It should also be noted that grass trimmer reels come in single-flow (used to cut grass only) and double-row, which are used to mow tall grass and small, thin-stemmed shrubs.

How long should be the line for the trimmer on the trimmer?

One piece of fishing line in the bobbin requires a length of 2 to 4 m, depending on the thickness of the line and the manufacturer’s recommendations. If you wind more than this, the line will not move smoothly and you may have problems pulling the new ends out while working. Coil out the necessary amount and cut it with a knife.

Unwind 2-4 m of fishing line (depending on the size of the spool), find the hole on the inside of the spool that locks the line for the trimmer, insert one end of the line there and start winding the line for the trimmer in the opposite direction of rotation of the spool on the trimmer.

Instructions for refilling the lines on your petrol trimmer

How to choose a fishing line

In order for your grass trimmer to work “like clockwork”, you need to choose the right line for your trimmer, that is, choose it based on the grass trimmer model and type of work. Two important parameters in this matter are the diameter and the cross section.

The diameter of the fishing line should correspond to the recommended for this model (in the passport of the product is necessarily specified ). Circle, square or sharp-edged (pentahedral) lines. round-section trimmer line is best for cutting young grass and lawns, while square and five-section lines are best if the grass is too tough and lawns are overgrown with weeds.

Grass trimmer head modifications

Grass trimmer mowing heads can be of different modifications: single line for lawn mowing (mowing with one line of line); double line for grass mowing and land clearing with automatic line feed or manual line length adjustment.

Modern manufacturers increasingly offer gardeners universal trimmers for grass with two-string automatic mowing heads.

Step-by-step instructions for threading a line into a grass trimmer

  • Push the clips inward until they click into place and remove the cover from the mowing head.
  • Carefully turn the spool, it is free from the holder, and now pull it out.
  • Cut two identical pieces of line (the edge of the line should be at an angle. this makes the job easier). Take one of them and insert the end of the fishing line into the special on the spool (there may be hooks, lugs, clips). Next, wind the string in the direction of the arrows. Spread the line evenly and tightly for the trimmer. Insert the end of the line in the hole provided on the spool.
  • Do the same operation with the second piece of fishing line, only tuck the end on the spool from the opposite side.
  • Return the spool with the fishing line to the mowing head. Through the holes in the spool pull out the ends of the line and tuck them into the special connector of the head.
  • Carefully straighten the line for the trimmer and close the cover. Cut off the excess line, leaving 12 to 15 cm. of each edge.
grass, trimmer, reel, line

All done. The grass trimmer is tucked in and ready for use. Now you can happily take on the mowing of your favorite clearing, dacha corner, yard territory.

It is important to remember that not only the quality of your work, but also your safety will depend on how you tuck the line into the trimmer for grass trimming.

Grass trimmer reel winding preparation

Initially, as a rule, the coil is installed to the head of the device itself. The coil consists of two parts. the cover and the spring.

You can buy the best quality electric grass trimmers and additional accessories here in the “Garden Mechanisms” online store at the lowest price for the selected product from the category. In the catalog on the link you can find the most popular, popular electric mowers of such brands as: Bosch, Makita, PATRIOT, Gardena, Hyundai and others.

grass, trimmer, reel, line
  • Whichever company you have a grass trimmer, the preparation steps are the same for all types. Dismantle the device, or rather remove the spool from the head of the grass trimmer. To do this, up to the stop press the locks located on the sides of the head body, and turn clockwise the head.
  • To open the mowing head easily, press the side latches, if you can’t do it with your hands, use a flathead screwdriver to help. Getting the spool out of the mowing head.
  • To find the right line for your trimmer, on the inside of the spool there should be digital markings that tell you the thickness and type of allowable line. All markings are usually in millimeters.
  • If you can’t find any numbers, the maximum allowable line diameter is indicated by the through-hole for inserting the line. The line for the trimmer should go forward and backward unhindered.

How to take out the line stuck in 36V Ryobi Line Trimmer and put a new line

The process of winding the line on the spool

  • After all the preparatory actions, we need to properly determine how exactly on your device will wind the line for the trimmer, by turning the cover or in the opposite direction.
  • Measure about 7 mm of the cutting material and insert one end of it through the bobbin hole. It is worth noting that the line for the trimmer is wound exactly on the mower style models with two sides. The winding direction of the line in these models is indicated on the bobbin itself.
  • The line for the trimmer is fed out to about 17 cm loosely, so that the ends can cut through the weeds. Let us add that it is not necessary to wind the line for the trimmer on a spool of great length. Leave about 5 mm distance from the line to the edge of the bobbin.
  • Two ends of the line are inserted into the holes of the bobbin. Both ends must be securely fastened to the head body.
  • Removed from the spool springs (if any) insert as they were removed, t.е. into the bobbin and the head body itself.
  • To determine if you have inserted the trimmer line into the grass trimmer correctly, you need to make sure that the element itself (the bobbin) is easily inserted into the head housing of your device. Pull the free ends of the fishing line out if necessary. To achieve this, you need to pull the trimmer line sharply out of the slot through the holes in the bobbin.

So, let’s assume you’ve figured out how to wind the line quickly, and most importantly correctly, onto the STIHL grass trimmer reel. All you have to do is correctly insert everything in the grooves and fasten the main cover on the device. Then you can press the bobbin itself and move counterclockwise until you feel the stop. If you do not feel the stop, then most likely you trimmer line you tucked the wrong trimmer and you have to start from scratch.

A few tips

If your trimmer line is wound correctly, it should retract automatically when you press the bobbin button. the trimmer line for your mowing device is one of the most important elements, without which the grass trimmer can lose all its functionality. It can be said that line for trimmer (cutting element) is the heart of your mower. Therefore, when buying a fishing line, give priority to its quality. Buying line for your trimmer from one company or another, compare it with the quality of the old line.

grass, trimmer, reel, line

What can be used instead of fishing line

Most mower users ask others or salespeople at specialty stores what else can be used (replaced) besides a fishing line. Many of them start to experiment and use unsafe methods, mounting different cutting elements on their grass trimmer, including. copper wire, metal, some manage to use guitar strings and even ropes, and some even use fishing line from fishing nets.

Handle shape

The manufacturers offer 2 options for the handle:

A “T” shaped handle is installed on models with auto-reeling line. The work is done with 2 hands on either side of the boom. This position is convenient for mowing large areas of vegetation. Grass cutter works the same way as a lawn trimmer. from one side to the other. Such a variant is not distinguished by maneuverability, works poorly on difficult terrain. Bicycle handlebar can be equipped with control buttons. In domestic types of grass trimmer start buttons are installed on the boom.

The classic grass trimmer model with a double-sided handle that has control buttons

Gasoline trimmer with a D-shaped handle is more maneuverable, it is convenient to mow grass in areas with difficult terrain. With this tool, the arms are positioned one above the other. The disadvantage of the handle. it is difficult to hold it, the management of such a device is more complicated.

Handle in the form of the English letter “J” is the most uncomfortable, so it is rarely found.

Step-by-step instructions on how to wind a trimmer line on a grass trimmer reel

You spend a lot of time in the garden or in the countryside when spring arrives. From such a problem, as grass and weeds, you will protect the trimmer for grass. This tool easily trims and mows grass in difficult areas, where an ordinary lawnmower can not do it under force. Grass trimmer. a very effective and handy tool for mowing grass along fences, flower beds, houses and rows in the garden. Several types of garden trimmers for grass (gasoline, electric and battery-powered) have been invented. It would seem that everything is fine, in your arsenal has

You may have such a great helper, but over time the cutting element wears out and it becomes necessary to replace the run out of fishing line. But not everyone knows how to thread a line into a grass trimmer. We suggest using the step by step instructions with pictures attached.

Instructions on how to wind a line for trimmer on the grass trimmer spool

  • 1. To begin with, the grass trimmer head must be disassembled. Press the catch on the body of the product and turn the cover clockwise. Remove the bobbin.
  • Now we have to figure out how to wind the line for the trimmer on the grass trimmer reel. We measure about 6-7 m of fishing line and insert the end into the hole of the bobbin.
  • Reel filament for grass trimmer from both sides. The winding direction is always indicated by an arrow on the bobbin.
  • Leave the ends of the cutting element 15 cm long free. Don’t wind too much fishing line. Leave 6 mm between the outer edge of the bobbin and the line.
  • Insert the other two ends of the line in the opposite holes of the bobbin.

In this article we have learned how to wind the line for trimmer on the grass trimmer spool. And if you have done everything correctly, when you press and hold the bobbin, it should extend again. line for the grass trimmer. a very important element without which the tool loses its function. In fact, this is the heart of the grass trimmer. Therefore, purchase at a specialized garden equipment store and approach the choice with special care. When buying a new line for your trimmer, be sure to compare it with a piece of the old used cutting element.