Where the sparks from the angle grinder should fly

Angle Grinder Safety

In order to reduce the likelihood of injury to yourself and others, the master needs to follow certain recommendations. In no case should you forget that in addition to sparks, disk pinching can also be a hazard.

In this case, the tool can be pulled out of the operator’s hands, and where the tool with discs that rotate at high speed will fly is very difficult. The consequences of such an accident can be chopped pieces of flesh, etc.

Interesting fact! The angle grinder was invented only in 1954, in Germany, and the colloquial name of the tool “angle grinder” appeared in the USSR in the 1970s, when the first copies began to be brought in. At that time they were produced in Bulgaria, and only in the countries of the USSR, angle grinders were called an angle grinder.

• Lateral placement of the adjustment knob. The handle should be on top, not below or to the side, but vertically. In this position, the master will be able to provide a tight and firm grip, and will be able to protect himself, as well as people from the consequences of “biting” the disc. In addition, sparks in this case fly to the side, and this also ensures safe operation.
• Direction of rotation of the disc. When cutting in the direction away from himself, the master will not fall under the jet of sparks, and therefore, usually beginners place the device in this way. But experienced craftsmen know that the casing protects against sparks perfectly, and that sparks are not as scary as a disc clamp. When cutting away from itself, the looped angle grinder will fly just to the master, which will be a guarantee of injury. During sawing towards itself and a slightly turned disc, the angle grinder will fly away from the master, to the ground during the “bite”.
• Arrangement of material during cutting. If you fix a metal sheet or pipe on both sides and cut it between the fasteners, then you will make a mistake. This action often leads to the fact that the disk is jammed at the end of the process. For this reason, one end must necessarily be weighed, and at the end of the cut the process of “unclamping” takes place, and the disc does not jam. In this position, the sparks from the material move away from the master.

Tightening the nut. Tightening the nut is just a waste of time, because during the work, the bolt itself will tighten to the required level, and when starting work, the standard tightening of the nut by hand is enough. Please note that if you tighten the nut with a wrench, then after it it will be difficult to unscrew it. The start button of the angle grinder is only pressed when the blade is free to move, which means that the saw must not be immersed in the cut before you start the working cycle of rotation.

We suggest considering a method that will leave your angle grinder spark-free.

Why do sparks start to fly

Metal discs for angle grinders rotate at an incredibly high speed, and during rotation, the cutting material begins to heat up to a high temperature.

The smallest particles of metal and stone begin to heat up and form sparks during friction. The flow of sparks can be very dangerous for the operator, as well as for nearby people and objects. Sparks can burn, ignite textiles or dry grass.

angle grinder without sparks. is such a recommendation from professionals possible?

angle grinder without sparks. is such a recommendation from professionals possible?

For everyone, an angle grinder familiar in everyday life is used for dismantling work, as well as for cutting various materials.

Sparks Fly As Bike Thief Grinds Through Lock At Mid Day In San Francisco || ViralHog

Its scope is incredibly large, and this is a big plus, but the risk of injury is a significant disadvantage. But we know how to remove it and tell you what kind of spark protection there is for an angle grinder.

Please note that sparks from an angle grinder are the most hazardous, as well as the possibility of a pinched disc.

non-sparking angle grinder

So, you need the angle grinder itself, a glue gun (exactly the one that melts the silicone rods) and any non-combustible material.

You only need a couple of dots to apply silicone to the protective cover of the device, because there is no need to glue tightly.

In the role of an impromptu shield for protection, you can even use an insole from roller skates (which will become an excellent material for making bearings), but it can be any other non-combustible material, for example, a piece of sandpaper, leather, a thin sheet of tin.

Next, glue this material onto the silicone to the already installed protective casing, and this will be the second level (a do-it-yourself mudguard, or, more precisely, a spark arrester).

Then you can continue with the standard work, but now do not worry that sparks will ignite something. And even more, such protection is a way to save from shrapnel, as it is a kind of continuation of the protective casing.

For short-term use of the device, this modification may not be necessary, but if you need to cut a lot of metal, then the spark arrester will be excellent protection. When the spark arrester is no longer needed, you can simply peel off the silicone glue, fortunately, the silicone separates from the metal without problems.

The principle of operation of the “angle grinder

What this machine is, firstly, the main working part is a disk. Sawing and grinding discs are different depending on the material with which you need to work. The very process of operation of an angle grinder, this is the movement of the nozzle disc at high speed, the disc has serrations, so you can cut the necessary material, and in a situation of violation of safety precautions, get wounds and cuts.

Which way should the sparks fly from the angle grinder

“Angle grinder”, as the craftsmen have long nicknamed the tool designed for cutting and grinding metals, stones and other materials, the angle grinder. The use of this tool is quite common both in construction and in agriculture and at home, for various kinds of domestic machinations. The car received such a name among the people because of the country of the manufacturer, as it is not difficult to guess Bulgaria.

Recently, the question “In which direction should the sparks fly from the angle grinder” has caused a real stir. And the fact is that people answer in different ways, and referring to their own personal experience. But if we talk not about experience, but about how to do it right. Then you need to carefully study safety and operating technology.

Safety engineering

Violation and non-observance of safety measures will lead to serious injury. Therefore, before starting work, you must carefully study the instructions, remember and follow. It is a violation of safety precautions to work without protection and to saw on yourself. It’s just beyond comprehension. The stand should be the correct legs bent at the knees, the angle grinder slightly to the side.

An angle grinder is a work tool that can be dangerous. The unit must be positioned towards you, with the heel. The head should never be on the mowing line of the cut. And in this regard, it is correct to saw with sparks from yourself or under a person, that is, into the legs, because:

• You can see where the sparks fly,
• The likelihood of catching a lawsuit or sawdust in the eye decreases, even when working with glasses, it can fly.
• When the disk expands (this happens), the fragments go away from themselves, and not onto a person.

Work technology

The direction in which the sparks fly depends on how familiar a person is with the technology of working with an angle grinder.

• The first is the grip. You need to hold the unit firmly with both hands, without transferring the weight to any one hand. In a kickback situation, with the correct grip, there will be no pulling out of the hands.
• The line should be laid out to the side away from the rotating disc, but not next to or on the mowing line of the cut.
• The direction of the sparks can be chosen both away from the master, and under him. the main thing is not on yourself. However, left-handers do not have to choose, the only possible option is the direction of sparks “for themselves”.
• When working with an angle grinder, there should be a bucket of water nearby as a precaution against fire.
• The tool cannot be put off anywhere while the disc is rotating. Naturally, when moving from one place to another in operation, the angle grinder must be turned off.

A few sparks flying

The conclusion of the direction of the sparks from the angle grinder depends on the master, to choose from either himself or for himself.

Answers:

Of course, there should be a defender on the angle grinder, this is not discussed. Of course, I am far from Aivazovsky, but I hope the meaning is clear. That is, in any case, something flies in us, either an instrument, as in the first case, or a bunch of fragments, as in the second. It was this flight that gave birth to a bunch of controversies, with evidence from each side, which of the evils is the lesser. over, I will say that on my channel on this topic there are about 500 Комментарии и мнения владельцев in several publications, where each side proves its point of view, arguing that it is right. I, to be honest, succumbed to the influence, and reasoned logically that the second option was more acceptable, apparently I followed the lead of the majority. But more recently, a brilliant idea occurred to me, what if I open the instruction manual and see what the tool manufacturer recommends. After all, they do not stupidly produce it, they calculate it, test it and only then launch it into the line. The argument that a cheap tool does not pass testing will not work here, since a cheap tool is completely copied from an expensive one, along with the instructions. And now I will briefly, in my own words, voice the instructions of the manufacturer of my Black Decker angle grinder, this is what they write about recoil:

• Hold the tool as firmly as possible and be sure to use the additional handle to secure with both hands. It is logical, perhaps if the tool is firmly fixed and does not watered anywhere, you can hold it.
• Your hands should never be near a rotating accessory (read the disc of an angle grinder). Affiliation, upon kickback, can bounce back onto your hand.
• Do not stand in the area where the angle grinder may fly. Agree, this is not the flight of the 7.62 bullet, the trajectory of the alleged flight of the angle grinder is very easy, not even calculated, but imagined. There is even a footnote here that recoil will push the tool will push the tool in the direction opposite to the direction of movement of the circle in the place of stopping.
• Be extremely careful when working with corners and sharp edges.

That’s all, the manufacturer did not even think to indicate in which direction the sparks should be launched. Of course, from the text it is clear that if you need to beware of an instrument flying at you, then by itself sparks in this case fly from you. And I think that the centuries-old dispute can be resolved by a simple logical conclusion, you do not need to stand where the sparks of the angle grinder (and with them the fragments of the disc) will fly, or the tool itself. Hold the tool firmly as well, do not put your hands close to the disc and take a closer look. And if you follow these simple rules, in principle, it is absolutely all the same in which direction the sparks fly, in the overwhelming majority of cases you will not be in the affected area of ​​either the fragments or the angle grinder itself. Well, I’m waiting for your opinion in the Комментарии и мнения владельцев =) P.S. I feel the battle will be noble! If the article was interesting and useful to you, then be sure, just be sure to like and subscribe. Also, do not forget about the YouTube channel, everything is interesting there too. Send all suggestions, wishes and criticism to badart@yandex.ru or in the Комментарии и мнения владельцев under the publication!

Anyway, everyone who took an angle grinder in his hands thought about this epoch-making question. how would it be more correct to cut, with sparks from himself or vice versa? After all, knowing the answer to this question, other accompanying “tasks” are automatically determined: How to properly hold an angle grinder and which side it is better to screw on the removable handle. In general, in this issue we will talk about these nuances. The angle grinder is a fairly common power tool and, for sure, most readers have it. After all, the range of work performed with its help is quite wide. angle grinder is used for cutting, grinding, deburring, etc.

• The most dangerous operation when working with an angle grinder is working with cutting discs. When cutting, it can pinch, and as a result break, the cutting disc. In this case, the disc itself, or rather, its fragments, become striking elements, and the tool of labor itself can turn into a murder weapon. It should be borne in mind that the part loses its rigidity during cutting and will bend. Cut, if possible, from the top!
• A common cause of biting and rupture of the cut-off wheel is the misalignment of the tool relative to the mowing line of the cut. This happens quite often with incorrect positioning or unsure work, the instrument should be held with a confident firm hand, as the captain holds the steering wheel of a ship, and at the same time fully understand what is happening with the instrument and the part.

You should not cut from yourself with sparks And then everything is simple, if you cut with sparks on yourself, then the angle grinder will fly away from you. And if you cut with sparks from yourself (as in the photo above), then when the disc is jammed, be prepared to meet a tool that rotates at a speed of 10,000 rpm. That is, if you are not wearing a bulletproof vest and a helmet, then all the same it is better to spark at yourself. Well, now let’s move on specifically to the topic of the question:

Spark from grinder

Answer: correctly and safely spark on yourself.

A good example of how to work with an angle grinder correctly. Sparks on yourself! Demonstration of the work of an angle grinder with sparks from yourself If you do the work correctly and work with an angle grinder with sparks towards yourself, then when you pull the angle grinder out of your hands, it will rush away from the worker. This significantly minimizes the chances of being seriously injured and injured. Visual animation aids for better understanding!

How should the sparks of an angle grinder fly correctly? By yourself or by yourself?

Don’t forget about PPE (personal protective equipment)

Also, if possible, use anti-noise glasses and headphones. Protect your eyes and ears. Dross in the eye is an immediate appeal to the doctor. Dear friends. Everything is written from practice. It is different for everyone. Someone will say that for 50 years they have been cutting order with an angle grinder. Not everyone is so lucky. Do not ignore safety precautions and manufacturer’s rules. There are a lot of stories and cases about injuries using an angle grinder, I think, and not only for me. All the rules are written in blood. Take care of yourself. All good! Thank you for attention. I would be glad to receive feedback in the Комментарии и мнения владельцев. Do not forget to support the article with like. The channel has a lot of material for you. I advise you to look: How much did the construction of the Crimean bridge cost and who built it? A few interesting facts about the bridge How much does it cost to lift a box of a house from various materials and the Moscow region in 2020 We make a two-room apartment from a one-room apartment. Part 1 I made a canopy for the porch of a house. I am sharing my first experience. How much money does it take to build a house. Overview of types of houses and What are the eco-friendly materials for building a house How to choose a contractor for building a house and what points you need to follow

Notice how the body of the angle grinder is tilted. the angle grinder is not pushed forward, but pulled. It’s much easier to hold it in your hands that way. So, the direction of the cut should be opposite to the rotation of the circle, because otherwise the circle may jump out of the cut. the angle grinder should be pulled over. If, in the case of sawing in the direction of rotation of the wheel, it jumps out of the cut, the angle grinder can roll on it along the surface of the part, tumble in weak hands, turn the cutting wheel towards you, and cut you in half. If the circle wedges and it jumps out also destroyed, in addition to the one described above, the inertia of rotation scatters its fragments on the sides. If the circle wedges during an oncoming cut and pulling on itself, on the contrary, it digs into the cut and quickly stops, and most of the fragments remain under the part, and the rest. in the casing.

In which direction you need to lead the angle grinder when cutting metal?

And so, the first thing that many manufacturers of an angle grinder advise is to cut in the direction that the movement of the tool and the rotation of the wheel coincide. And then the possibility of an uncontrolled exit of the circle from the slot is excluded. But there is one inconvenience, with this method of work, the markings on the material are often hidden by flying sparks. Here already from personal experience. Usually I go over the markings with an angle grinder, just to make a small indentation. Firstly, the marking is so much better visible, and secondly, a depression appears on the metal, and it is much easier to control the angle grinder directly while cutting the metal, it goes clearly along the chamfer. Well, a few life hacks with an angle grinder from my YouTube channel:

A dispute has arisen with a colleague at work. It means that he tells me that it is correct to turn the body of the angle grinder so that the sparks fly from the worker. I don’t think so. I think it’s right to work the angle grinder with sparks on yourself! Help resolve the dispute!

How to cut with an angle grinder: for yourself or away from yourself

Angle grinders are in many farms and garages, but most owners do not know how to properly hold and use an angle grinder. Therefore, they make mistakes that can lead to marriage at work, which is even worse. to serious injuries. It must be remembered that an angle grinder is a very dangerous tool. Therefore, before using it, you need to learn a few safety rules.

How to cut correctly

First of all, you need to correctly pick up the instrument. Right-handers hold the angle grinder with their right hand by the body. In this case, the circle is located on the left, and the gearbox on the right side of the machine. With your left hand, you need to hold the tool by the handle, which is screwed into the body. The correct position of the handle is up. The protective cover should cover the disc and hands, throwing sparks away from the worker. For left-handers, the handle is screwed in from the other side of the body, the protective cover is rotated and fixed in the desired position.

Tool manufacturers give three main tips for working with an angle grinder: hold firmly with your hands, stay away from the cut line, stop and start the machine if the blade is jammed.

How and in which direction to cut, everyone decides for himself, given the fact that when biting, the angle grinder is thrown in different directions.

Angle Grinder Safety

Grinding and cutting power tools are hazardous activities. Therefore, when working with an angle grinder, it is necessary to take into account the possibility of direct or indirect action of factors hazardous to health:

• cold or heat;
• poor illumination of the workplace;
• strong noise, vibration from a typewriter;
• great physical activity;
• rotating parts of equipment;
• falling objects (processed materials);
• flying off sparks and solid particles of parts;
• work at height, depth or in a confined, hard-to-reach place;
• danger of electrical injury.

To minimize the action of hazardous factors, and as a result, to preserve life and your own health, you can observe the safety rules when operating devices with open rotating parts. To do this, you need to use personal protective equipment (abbreviated as PPE), fix the workpieces well, choose a safe place, start and finish work correctly.

Correct start, stop and breaks

Before turning on the device, it is worth carefully examining and carefully checking the disc. Do not use tips that are chipped, delaminated, cracked or otherwise damaged.

Before connecting to the network, the cutting (grinding) wheel must be installed on the angle grinder with a pattern upwards, then tighten it with a special nut. The size, as well as the permissible revolutions, are indicated in the technical documentation for the tool.

The mismatch of characteristics leads at least to a defect in work, premature wear of the disc, in the worst case. to injuries.

When inspecting the instrument, you need to check that:

• there is no damage or cracks on the case;
• serviceability of the cable (cord), protective tubes and plug;
• the handle is well screwed on;
• the circle is fenced, and the casing is securely fixed.

After that, the idle operation of the tool is checked. To do this, you need to connect the plug to the outlet, turn on the power button and the latch. Observe for a minute the operation of the angle grinder. Make sure that it works without extraneous sounds, excessive vibration, and the disc does not touch the protective casing. When disconnected, the malfunction or functionality of the power button and latch will become clear. If everything is ok, you can get to work.

To take a break from work, you need to turn off the power with the button, wait until the disc has come to a complete stop, put the angle grinder and unplug it.

Interruptions in work are usually associated with overheating of the disc or angle grinder, replacement of attachments, the need to move the workpiece or the worker himself. In any case, you must first turn off the button, and then disconnect from the network. It is important to monitor the instrument and avoid overheating.

Cut on yourself

There are many supporters of this method. It is only important not to forget that when you move the angle grinder towards yourself, the sparks must necessarily fly in the other direction. This minimizes the risk of biting the disc. Although he always stays. Therefore, when moving the tool towards yourself, it is imperative to leave the mowing line of the cut.

Workplace safety

Regardless of where the workplace is located. in the garage, in the country or in a free area, it must be well lit, meet basic safety requirements.

Requirements for the equipment of the workplace:

• A workbench, table, rack, wardrobe or bedside table must be installed for storage, as well as placement of devices, tools for productive safe work.
• All immovable equipment is securely placed (attached) on the floor.
• The surfaces of the workbench and rack must be at least as large as the workpieces and tools used.
• The surface of workbenches is made of sheet steel, aluminum, and other non-combustible materials.
• The vise must securely grip the workpiece. On the surfaces of the vise jaws there should be a cross notch with a depth of 0.5. 1 mm for every 2. 3 mm.
• The vise is fastened so that the workpieces are at the level of the worker’s elbow.
• On a closed vise, the gap between the jaws should not be more than 0.1 mm. Handle and jaws. no potholes or burrs.
• The movable part of the vise should not fall out when fully unscrewed and move smoothly, without jerking.
• The floor around the workbench, as well as the entire work area, must be dry and level.
• Power tool outlets are positioned above the level of the workbench work surface.

When working at a height (more than 1.5 m), it is necessary to use scaffolding (scaffolding) with a handrail of 1 m, sheathed from below with a continuous sheathing to a height of 150 mm or higher.

It is not recommended to use coasters, barrels, boxes that accidentally come to hand. Scaffolding (scaffolding) must not be overloaded. In any case, when working with an angle grinder, you need to have a flat, solid surface under your feet.

Individual protection means

The name PPE, or personal protective equipment, is understood as means for personal use, which are used to protect against pollution, prevent or reduce the effects of harmful and dangerous factors. For most workers, this is workwear appropriate for the profession. It usually includes pants, a jacket, a hat, closed shoes. Since the angle grinder is a tool of increased danger, the clothing is supplemented with other protective equipment:

• glasses or visor;
• ear muffs or earplugs (ear plugs);
• vibration-insulating gloves;
• respirator, especially when cutting stone, tiles, concrete or slate.

The goggles will protect you from sparks, small debris or a grinding disc. The use of headphones or ear plugs helps to eliminate noise, thus avoiding difficulties with hearing after work. The gloves will protect you from abrasion and vibration. A respirator against a large amount of dust generated.

Where should the sparks from the angle grinder fly?

In the last post, we figured out which side to put the cut-off wheel correctly on. Now I want to speculate a little about which direction the wheel should rotate when cutting, and how to properly hold the angle grinder.?

Since I already had an instruction from the Metabo angle grinder in my hands, I decided to see how this issue is described there:

That is, regardless of the cutting material, because it is not mentioned, the cut should be made in the opposite direction. At the same time, I want to note from myself that cutting with an angle grinder follows what is intended for cutting with an angle grinder. If you suddenly want to use an angle grinder clearly not for its intended purpose, and cut, for example, a profiled sheet or other equally thin materials that are usually cut with scissors, then it will be difficult and dangerous to cut in the opposite direction. Therefore, I want to clarify again. the instructions describe only cases of using the tool for its intended purpose.

If you look at the drawing in large, you can see that this is a top view, and the work is carried out with a small angle grinder, although this is a common drawing for all grinders:

Notice how the body of the angle grinder is tilted. the angle grinder is not pushed forward, but pulled. It’s so much easier to hold it in your hands.

So, the direction of the cut should be opposite to the rotation of the wheel, because otherwise the wheel may jump out of the cut, and the angle grinder should be driven towards you. If the wheel jumps out of the cut, the angle grinder can roll on it on the surface of the part at you, tumble in weak hands, turn the cutting wheel towards you, and cut you in half. If the circle wedges and it jumps out also destroyed, in addition to the one described above, the inertia of rotation scatters its fragments on the sides. If the circle wedges during an oncoming cut and pulling on itself, on the contrary, it digs into the cut and quickly stops, and most of the fragments remain under the part, and the rest. in the casing.

Often, with such a counter-cutting, sparks fly to the worker, and also close the cutting direction. And the fragments of the circle, in the event of its destruction, in this case, will also fly in the direction of the sparks. How then to be?

I think safety is more important than being able to accurately control the cut. When cutting sheets, you can use the corner guide. When cutting parts, their transverse size does not require constant control of the cutting direction. As for sparks and possible fragments of the wheel, then it is important to learn how to properly hold the angle grinder. This is not difficult in a workshop. The right hand on the additional handle, perpendicular to the body of the angle grinder, at an angle of 100-110 degrees, that is, the right elbow is even further than the front edge of the circle. Left on the case with a button, parallel to the angle grinder. angle grinder parallel to your body. Sparks should be flying past to your left. The cut is controlled from above and slightly to the right, above the additional handle. In the plane of rotation of the circle, you should not be at all.

In the conditions of a real object, for example, when dismantling metal structures, it is impossible to keep an angle grinder all the time as described. Here all the hope is for a casing, a mask, overalls and intelligence. However, you should always keep in mind the recommendations for the direction of rotation of the wheel and guidance of the angle grinder. With each cut, you need to understand in which direction the angle grinder will tear when it gets jammed, where the wheel fragments will fly, where the angle grinder itself will fly, how it will tumble at the same time, and immediately change the position if the result does not suit you.

On the farm, very often it is necessary to cut off pieces from long pipes, fittings, etc., which lie on the ground. It is often not possible to raise them to the level of a vice. I have to cut on the ground, and even with a large angle grinder. How to protect yourself as much as possible in this case?

For several years now I have been working from time to time with a large angle grinder with 230 mm discs. Naturally, with this mode of operation, I will always have little experience, so I would like to determine for myself the safest methods of work.

The safest handstand with a heavy angle grinder seems to me like this. The right hand, as usual, is on the additional handle, the left hand is on the handle with a button. The right leg, suppose, fixes the pipe on a wooden block, pressing it from above, or simply stands on the ground if the pipe is fixed. I bend over and put my right shoulder on my right knee. In this position, I am in a position similar to the position in the workshop, but the weight of the angle grinder does not fall on the muscle of the right arm and back, but on the support in the form of a knee. The left leg is laid back, the foot is extended perpendicularly, adding stability, but it does not enter the plane of rotation of the circle.

The stand described above is not always convenient, for example, if it is necessary to make a deep cut of a wide pipe that cannot be rotated. Then I just stand up so that the sparks fly back between my legs. In this case, the control of the cut is carried out either on the left, from the side of the circle, or on the right (then the right shoulder again rests on the right knee). In the case of the scattering of fragments, all hope in the above-described case is only on the shield. But here it is important not to give the circle lateral forces, otherwise it will be ripped off the shaft, tearing out the middle from it, which will remain under the nut, and it will jump off the angle grinder, continuing to rotate at a breakneck speed. Since you are in the plane of its rotation, it can cut you in half, bouncing off the part or off the ground. The circle tore off like this when I cut off the rusted bolts from the plane, on which I slightly pressed with the plane of the circle. Fortunately, the circle came off neatly and just went to the side.

A guard on an angle grinder is required. When repairing cars, they often use small angle grinders with grinders or even cut-off wheels without shields to crawl up comfortably. Suicides, why.

Glasses (namely, protective, covering the eyes from all sides) are required. When cutting or sanding, a pile of abrasive and metal to be grinded fly in different directions, ricocheting off everything from which it is possible. For dismantling metal structures at the facility, a mask is preferable, but only closed so that ricocheting sparks do not fly under it, and reinforced to keep flying fragments of the circle when it is destroyed. The minus of the mask is that she, bitch, fogs up. But if you wear a respirator, which is important during daily work, there is practically no fogging. The mask for mowing the grass cannot be used. It is open at the bottom, and does not protect against the ricochet of sparks, but on the contrary, catches them and makes them ricochet again in the face. And yes, when working with an angle grinder on a daily basis, you must use headphones or earplugs, otherwise you will have a quick hearing loss.

Gloves (preferably rough, suede). Do not allow sweaty hands to slip on the handle, partially protect your fingers from disc fragments and flying chips. Protect the skin from cuts with metal burrs, which are abundant on the cuts of parts after an angle grinder.

Boots without holes, preferably working ones, with a metal insert. How I get pissed off by workers in slippers with bare toes or socks sticking out of them! Is it really convenient to work in this “shoe” yourself? Well, not on the beach, after all! A metal blank will fall on your fingers, and a kick! I tripped over a severed metal pipe and cut my leg with a metal burr! And walking in slippers is uncomfortable! Where did this fashion come from here.

A special shirt that completely covers the body. Possibly a leather apron from sparks. When dismantling metal structures, a helmet is required! There is always something breaks and falls!

That’s all. Write any additions or remarks in the Комментарии и мнения владельцев.